Danfoss 102 Montageanleitung

102

Installation & User Instructions

including Factory Replacement Units (FRU)

electro-mechanical mini-

programmer for controlling

hot water and heating

INDEX

Index

Installation

Product speciﬁcation 3

Installation 4-5

Wiring 6

User

Your programmer 7

Setting the time of day 8

Setting the programme 8-9

Selecting operating mode 10

Temporary overrides 11

Contact details 12

Please Note:

This product should only be installed by a qualiﬁed

electrician or competent heating installer, and

should be in accordance with the current edition of

the IEEE wiring regulations.

Speciﬁcation

Power supply 230Vac ± 15%, 50 Hz

Switching action 1 x SPST, Type 1B

Max. Switch rating 264Vac, 50/60Hz, 6(2)A

Timing Accuracy ±1 min./month

Enclosure Rating IP20

Max. Ambient Temperature 55°C

Dimensions, mm (W, H, D) 112 x 135 x 69

Design standard EN 60730-2-7

Control Pollution Situation Degree 2

Rated Impulse Voltage 2.5kV

Ball Pressure Test 75°C

Product speciﬁcation

Installation & Speciﬁcation

Installation Instructions

Installation

1. Loosen the ﬁxing screw in

the base of the unit to release

the grey plastic Wiring Cover.

Ensure the protective tape

over the thumbwheel remains

in place.

2. Holding the unit clockface

downwards, press ﬁrmly in

the centre of the wallplate

and slide it from the module

as shown.

Installation

Pre-Selector wheel

Selector switch

Plug-in replacement

module

Wallplate/Terminal

block (not with FRU

units)

wallplate/

terminal

block

plug-in

module

NB. For FRU units - go straight to to point 4 on page 5

3. Fix the Wallplate/Terminal Block to the wall with

countersunk No.8 woodscrews or to a steel box to BS

4662. 1970 or a surface mounting steel or moulded

box having centres of 23/8” (60.3mm).

4. Referring to the Wiring Diagrams on page 6, connect

the unit as shown. Ensure that terminals 3 and 6 are

linked where required (Mains Voltage applications) with

insulated cable capable of carrying full load current.

5. Ensure all dust and debris has been cleared away

from the area, then plug the module ﬁrmly into the

wallplate ensuring that the hook at the top of the

wallplate engages with the slot at the back of the body.

Press the module down until it locates solidly.

6. Cut a cable aperture in the Wiring Cover if necessary;

replace the Wiring Cover, and tighten the ﬁxing screw.

7. Switch on Mains & test for correct operation as follows:

i) Remove protective tape from pre-selector wheel.

ii) Remove dial cover & rotate the clock dial two

complete revolutions to clear the mechanism.

ii) Check that all positions of the Selector Switch

and Tappets operate correctly. (See instructions

in User Booklet.)

8. Replace the dial cover. Finally leave this booklet,

containing the USER instructions with the Householder.

9. If the unit is to be left turned off and is in a dusty

atmosphere, protect the pre-selector wheel by re-

afﬁxing the protective tape.

IMPORTANT: Remove tape prior to putting unit into service.

Installation

Wiring

102, 102E5, 102E7

Wiring

LNLN

Motor

Brown

Call

Grey

Blue

HP2 spring return

zone valve

Cylinder Stat

L641A

Orange

To Boiler & Pump

Room

Stat

Com

Room

Stat

Com

Call

Boiler

Pump

Mains

Supply

Mains

Supply

Link Link L

1235612356

102 Terminals

1) Typical domestic gas or oil fired system

with gravity hot water and pumped heating

(if a room stat is not required, wire pump L

directly to terminal 2 on the 102).

2) Fully pumped system with cylinder stat in

HW circiut and room stat and 2 port spring

return zone valve in heating circuit.

User Instructions

Your programmer

Your 102 mini-programmer allows you to switch your

heating and hot water on and off at times that suit you.

Normally the 102 provides 2 ON periods and 2 OFF

periods each day. However 1 ON and 1 OFF period can be

obtained by using the Pre-Selector Wheel (see page 11).

You can choose whether the 102 controls your hot water &

heating together, just the hot water or neither system (OFF)

using the manual rocker switch.

Overview

Preselector wheel

Dial cover

Wiring cover

Rocker

switch to

manually

select

programme

operation

Setting the time of day

The dial on the front of the 102 displays the hours of the

day using the 24hour clock.

 Remove dial cover (turn

slightly to the left and

pull off)

 Turn the dial clockwise

until the correct time is

aligned to the TIME

mark (as shown).

IMPORTANT: turn the dial clockwise only

Remember you will have to re-set the time after

a power-cut, and also when the clocks change

in Spring and Autumn.

Setting the programme (Tappets A, B, C, D)

1. If not already done so, remove the dial cover (turn

slightly to the left & pull off)

2. Decide when you want your hot water and heating

to come on and go off. While gripping the dial knob

slide the RED tappets to the required ON times and

the BLUE tappets to the required OFF times (the

tappets may be quite stiff to move)

Note: Tappets can be moved around the dial in a clockwise

or anti-clockwise direction, as convenient.

TIME mark

Setting the time & the programme

Example:

If you want your system ON between 8am and 10am

and again between 4pm and 11pm, set the tappets as

shown. (A to 8, B to 10, C to 16, D to 23).

Remember:

Red tappets (A and C) switch ON

Blue tappets (B and D) switch OFF

3. Ensure that the installer has removed the protective

tape covering the pre-selector wheel.

4. Using the dial knob, rotate the dial completely at least

twice, clockwise only, to clear the mechanism.

Setting the programme

A = 1st ON

B = 1st OFF

C = 2nd ON

D = 2nd OFF

Selecting operating mode

The Rocker Switch on the side of the unit is used to select

how your 102 controls your hot water & heating system.

You can manually select either:



hot water only

 hot water & heating together

 neither (system OFF)

Switch positions

The 102 unit is now set,

and the current status of

the mini-programmer can

be seen on the wheel at the

top righthand corner of the

unit, (e.g. “OFF UNTIL C”).

Hot water only

System OFF

Heating & Hot Water together

Andere Handbücher für 102

Inhaltsverzeichnis

Andere Danfoss Temperaturregler Handbücher

Danfoss

Danfoss L66 Bedienungsanleitung

Danfoss

Danfoss Optyma Plus OP-MPS Bedienungsanleitung

Danfoss

Danfoss ECL Comfort 310 Bedienungsanleitung

Danfoss

Danfoss EKC 319A Bedienungsanleitung

Danfoss

Danfoss RX1 Bedienungsanleitung

Danfoss

Danfoss ECL Comfort 110 Bedienungsanleitung

Danfoss

Danfoss FP735Si Bedienungsanleitung

Danfoss

Danfoss FP715 Montageanleitung

Danfoss

Danfoss ECL Comfort 210 Bedienungsanleitung

Danfoss

Danfoss EKC 101 Bedienungsanleitung

Danfoss

Danfoss 3060 Montageanleitung

Danfoss

Danfoss ECL Comfort L76 Bedienungsanleitung

Danfoss

Danfoss FHV-A Bedienungsanleitung

Danfoss

Danfoss ECL Comfort 210 Bedienungsanleitung

Danfoss

Danfoss ECL Comfort 210 Bedienungsanleitung

Danfoss

Danfoss ECL Comfort 100M Bedienungsanleitung

Danfoss

Danfoss 060R9769 Bedienungsanleitung

Danfoss

Danfoss CP715 Si Montageanleitung

Danfoss

Danfoss EKC 366 Bedienungsanleitung

Danfoss

Danfoss ECL Comfort 310 Bedienungsanleitung

Danfoss

Danfoss Optyma AK-RC 204B Bedienungsanleitung

Danfoss

Danfoss ECL Comfort P30 Bedienungsanleitung

Danfoss

Danfoss ECL Comfort 210 Bedienungsanleitung

Danfoss

Danfoss M150 Bedienungsanleitung

Beliebte Temperaturregler Handbücher anderer Marken

Swegon

Swegon LUNAd MB Bedienungsanleitung

Lucky Reptile

Lucky Reptile Thermo Control II Bedienungsanleitung

SENSORMETRIX

SENSORMETRIX Argon 100 Bedienungsanleitung

Fuji Electric

Fuji Electric PXE4 Bedienungsanleitung

Yuyao gongyi

Yuyao gongyi XMT-808 series Bedienungsanleitung

Selec

Selec TC544C Bedienungsanleitung

P.W. KEY

P.W. KEY rt-208gt Bedienungsanleitung

Future Design

Future Design FDC-9200 Bedienungsanleitung

BH Thermal

BH Thermal BriskONE Bedienungsanleitung

Omron

Omron E5EX-H Bedienungsanleitung

West Control Solutions

West Control Solutions KS 45 Kurzanleitung

MCS

MCS RITC-15B Bedienungsanleitung

SMC Networks

SMC Networks Thermo-con INR-244-639 Bedienungsanleitung

eltherm

eltherm Ex-TC It Series Bedienungsanleitung

Omron

Omron C200H-TV Series Bedienungsanleitung

industrie technik

industrie technik CA1 Bedienungsanleitung

KRAL

KRAL EET 32 Bedienungsanleitung

dixell

dixell XR420C Verdrahtungsschema