Danfoss 3060 Montageanleitung

3060

Installation & User Instructions

electro-mechanical

programmer for controlling

heating & hot water

This product complies with the following EC Directives:

Electro-Magnetic Compatibility Directive.

(EMC) (2004/108/EC)

Low Voltage Directive.

(LVD) (2006/95/EC)

INDEX

Index

Installation

 Productspecication 3

 Installation 4

Wiring 4-5

User

 Yourprogrammer 6

 Programmingtheunit 6-7

 Settingtheclock 7

 Usingtheprogrammer 8-9

 Contactdetails 12

Please Note:

This product should only be installed by a qualied

electrician or competent heating installer, and

should be in accordance with the current edition of

the IEEE wiring regulations.

Specication

Power supply 230±15%Vac,50/60Hz

Switchaction 2xSPST,type1B

Switchrating

Max264Vac,50/60Hz,3(1)A

Timingaccuracy ±1min/month

Enclosurerating IP30

Max.ambienttemperature 55°C

Dimensions,mm(W,H,D) 102 x 210 x 60

Designstandard EN60730-2-7

Construction Class1

ControlPollutionSituation Degree 2

RatedImpulseVoltage 2.5kV

BallPressureTest 75°C

Product specication

Installation Instructions

Specication

3060

Installation

1. Removelowersettingdial.Setallfourtappetstotop

ofupperdial.Unscrew4BAscrewandremoveouter

case.

2. Slackentwoscrewssecuringplug-inmoduleto

backplateandseparatemodulefrombackplateby

pullingupwards.

3. Fixbackplatetowall(3holexing).

4. Referringtowiringdiagramsbelowandopposite

makeelectricalconnectionsasshown(asapplicable).

Thediagramsindicatethatterminals3and5arenot

internallyconnectedtotheprogrammerandmay

thereforebeusedassparewiringterminalsifrequired.

5. Easeofinstallationcanbeachievedbytheuseofthe

DanfossRandallWiringCentrewhichisobtainable

frommostBuildersMerchantsandDistributors.

NOTE: If a Wiring Centre is used follow the

installation instructions included with that unit and

not the following wiring diagrams.

6. Securecablecoresundercableclamp.

Wiring

12345678910

S/L LN

Brown

Orange

Grey

Blue

Danfoss Randall

HP22 or HP28

SRZV (Hot Water)

Brown

Orange

Grey

Blue

Danfoss Randall

HP22 or HP28

SRZV (Heating)

Flying lead Flying

lead

(N)

1234567

Danfoss Randall

ATC Cylinder Stat

3 core

2 core3 core

Danfoss

Randall

RMT230

Room Stat

3060

Te rminals

Mains

Supply

2 core +

3 or 4 core

Boiler Pump

Permanent line

supply for boiler

if required

1234567

Boiler

3Danfoss Randall

ATC Cylinder Stat

Danfoss

Randall

RMT230

Room

Stat

Pump

3060

Te rminals

Mains

Supply

WIRING - FULLY PUMPED SYSTEM

WIRING - GRAVITY HOT WATER SYSTEM

NOTE: This unit is NOT suitable for use with fully motorised zone valves

requiring both ON and OFF electrical signals when used in the heating

circuit

12345678910

S/L LN

Brown

Orange

Grey

Blue

Danfoss Randall

HP22 or HP28

SRZV (Hot Water)

Brown

Orange

Grey

Blue

Danfoss Randall

HP22 or HP28

SRZV (Heating)

Flying lead Flying

lead

(N)

1234567

Danfoss Randall

ATC Cylinder Stat

3 core

2 core3 core

Danfoss

Randall

RMT230

Room Stat

3060

Te rminals

Mains

Supply

2 core +

3 or 4 core

Boiler Pump

Permanent line

supply for boiler

if required

1234567

Boiler

3Danfoss Randall

ATC Cylinder Stat

Danfoss

Randall

RMT230

Room

Stat

Pump

3060

Te rminals

Mains

Supply

WIRING - FULLY PUMPED SYSTEM

WIRING - GRAVITY HOT WATER SYSTEM

NOTE: This unit is NOT suitable for use with fully motorised zone valves

requiring both ON and OFF electrical signals when used in the heating

circuit

User Instructions

Your programmer

The3060programmerallowsyoutoswitchyourhotwater

andheatingonandoffattimesthatsuityou.

Fourtappetsonthetimingdialletyoudecidewhenyou

wantyourhotwaterandheatingtocomeonandgooff

eachday.Theprogrammerprovides2ONtimesand2

OFFtimesperday.

Usingthelowerdialyoucanchoosehowyoucontrolyour

HeatingandHotWater,eitheratthesettimes,constantly

ON,constantlyOFF(eachindifferentcombinations).

Duringthesummerthecentralheatingcanbeturnedoff,

whilststillcontrollingthehotwateratthesettimes.

Your Programmer & Programming the unit

Programming the unit

TherearefourTAPPETSonyourtimingdial,tworedand

twoblue:

o the redtappetsaretheON switches

o the bluetappetsaretheOFF switches

1. Holdthecentralblack&

silverknobwithonehand

andmovetheredtappet

marked‘A’clockwise to

thetimeyouwantyour

HEATING/HOTWATERto

switch oninthemorning.

 NB.youmayndthetappetsquitestiff,soyoumay

havetopushthemquitermlytomovethem.

Setting the clock

2 Stillholdingthecentralknob,movethebluetappet

 marked‘B’tothetimeyouwantyourHEATING/HOT

 WATERtoswitchoffinthemorning.

3 Youcansetyourothertwotappetsinthesameway

 tosetyourHEATING/HOTWATERfortheafternoon

 orevening.

EXAMPLE

 (NB.Clockisin24hourmode)

 IfyouwantyourheatingandhotwaterONbetween

 7amand10amandONagainbetween5pmand

 11pm,settappetsasfollows:

  Aat1stONtime=7

  Bat1stOFFtime=10

  Cat2ndONtime=17

  Dat2ndOFFtime=23

Setting the Clock

o Turnthedialclockwise

until the correct time is

lined up with the dot

 labelledTIME

NB.clockisin24hour

 mode

REMEMBER

You will have to reset the time after a power

cut and also when the clocks change in

Spring and Autumn

Using the Programmer

Theselectorswitchisusedtoselecthowthe3060controls

yourhotwaterandheating.Theheatingandhotwatercanbe

operatedtogetherinvariouscombinations,orthewatercan

becontrolledonitsown(i.e.duringthesummerwhenonly

hotwaterisrequired).

Therearesixpositionsintowhichtheselectorswitchmay

beset.

1 - H OFF / W OFF

 BothHeatingandHotWaterwillremainOFFuntilyou

changethesetting.

2 - H TWICE / W TWICE

 InthispositiontheHeatingandHotWaterwillboth

comeonandgooffaccordingtothetimesyouhave

programmed(ONatA,OFFatB,ONatC,OFFatD).

3-H ONCE / W ONCE

 ThissettingoverridestappetsBandC,soboth

HeatingandHotWaterwillswitchONatthetime

markedbytappetAandwillstayonuntilthetime

markedbytappetD.Bothserviceswillthenswitch

OFFuntil‘A’thenextday.

Using the programmer

H+W

OFF

H - TWICE

W - ONCE

H - ONCE

W - ONCE

H - TWICE

W - TWICE

H - OFF

W - TWICE

Using the programmer

4 - H ON / W ON

 Thisisthe‘CONSTANT’positionandtheprogrammer

willremainpermanentlyONforbothHeatingandHot

Water,irrespectiveofthepositionofthetappets.

5 - H TWICE / W ONCE

 Inthispositiontheheatingwillcomeonandgooff

accordingtothetimesyouhaveprogrammed(ONat

A,OFFatB,ONatC,OFFatD).

 TheHotWaterwillcomeonatAandstayonuntilD.

6 - H OFF / W TWICE

 InthispositiontheHeatingwillbepermanentlyOFF

andtheHotWaterwillcomeonandgooffaccordingto

thetimesyouhaveprogrammed(ONatA,OFFatB,

ONatC,OFFatD).

Note:

If hot water is required all day with the heating shut

off (i.e. heat off, water once)

o Turntheselectorswitchto‘Htwice/Wonce’and

 turndowntheroomthermostattoitslowest 

 setting.

If constant hot water is required with heating off (i.e.

heat off, water on)

o Turntheselectorswitchto‘Hon/Won’andturn

 theroomthermostattoitslowestsetting.

Inhaltsverzeichnis

Andere Danfoss Temperaturregler Handbücher

Danfoss

Danfoss ECL Comfort 310 Bedienungsanleitung

Danfoss

Danfoss ECL Comfort 210 Bedienungsanleitung

Danfoss

Danfoss EKC 101 Bedienungsanleitung

Danfoss

Danfoss C17 Montageanleitung

Danfoss

Danfoss 103E7 Montageanleitung

Danfoss

Danfoss M150 Bedienungsanleitung

Danfoss

Danfoss ECL Comfort 210 Bedienungsanleitung

Danfoss

Danfoss CP715 Si Montageanleitung

Danfoss

Danfoss FP715Si Montageanleitung

Danfoss

Danfoss ECL Comfort 296 Bedienungsanleitung

Danfoss

Danfoss ECL Comfort 210 Bedienungsanleitung

Danfoss

Danfoss ECL Comfort 210 Bedienungsanleitung

Danfoss

Danfoss 060R9769 Bedienungsanleitung

Danfoss

Danfoss FHV-A Bedienungsanleitung

Danfoss

Danfoss MBT 5252 Bedienungsanleitung

Danfoss

Danfoss ECL Comfort L76 Bedienungsanleitung

Danfoss

Danfoss ECL Comfort 310 Installationsanleitung

Danfoss

Danfoss ECL Comfort 110 Bedienungsanleitung

Danfoss

Danfoss L66 Bedienungsanleitung

Danfoss

Danfoss ECL Comfort 310 Bedienungsanleitung

Danfoss

Danfoss AVQ PN16 Bedienungsanleitung

Danfoss

Danfoss EKC 361 Bedienungsanleitung

Danfoss

Danfoss Link RS Bedienungsanleitung

Danfoss

Danfoss ECL Comfort 210 Bedienungsanleitung

Beliebte Temperaturregler Handbücher anderer Marken

Swegon

Swegon LUNAd MB Bedienungsanleitung

Lucky Reptile

Lucky Reptile Thermo Control II Bedienungsanleitung

SENSORMETRIX

SENSORMETRIX Argon 100 Bedienungsanleitung

Fuji Electric

Fuji Electric PXE4 Bedienungsanleitung

Yuyao gongyi

Yuyao gongyi XMT-808 series Bedienungsanleitung

Selec

Selec TC544C Bedienungsanleitung

P.W. KEY

P.W. KEY rt-208gt Bedienungsanleitung

Future Design

Future Design FDC-9200 Bedienungsanleitung

BH Thermal

BH Thermal BriskONE Bedienungsanleitung

Omron

Omron E5EX-H Bedienungsanleitung

West Control Solutions

West Control Solutions KS 45 Kurzanleitung

MCS

MCS RITC-15B Bedienungsanleitung

SMC Networks

SMC Networks Thermo-con INR-244-639 Bedienungsanleitung

eltherm

eltherm Ex-TC It Series Bedienungsanleitung

Omron

Omron C200H-TV Series Bedienungsanleitung

industrie technik

industrie technik CA1 Bedienungsanleitung

KRAL

KRAL EET 32 Bedienungsanleitung

dixell

dixell XR420C Verdrahtungsschema