Danfoss ECtemp Touch Bedienungsanleitung

Danfoss ECtemp Touch

Electronic Intelligent Timer

Thermostat

Installation Guide

electricheating.danfoss.com

Danfoss ECtemp Touch

Installation Guide2

1 Introduction

The Danfoss ECtemp Touch is an electronic programmable

timer thermostat used for controlling electrical oor heat-

ing elements. The thermostat is designed for xed instal-

lation only and can be used for both direct heating of the

entire room and for comfort heating of the oor. Among

others, the thermostat has the following features:

• A touchscreen display with backlight.

• An easy-to-follow menu-driven programming and

operation.

1 Introduction � � � � � � � � � � � � � � � � � � � � � 2

1.1 Technical Specications . . . . . . . . . . . 3

1.2 Safety Instructions . . . . . . . . . . . . . . . 5

2 Mounting Instructions � � � � � � � � � � � � � � � 6

3 Settings � � � � � � � � � � � � � � � � � � � � � � � � 9

3.1 Initial Settings. . . . . . . . . . . . . . . . . . 9

3.2 Forecast . . . . . . . . . . . . . . . . . . . . 13

3.3 Window Open . . . . . . . . . . . . . . . . 15

3.4 Maximum Floor Temperature . . . . . . . 16

4 Symbols � � � � � � � � � � � � � � � � � � � � � � � 18

5 Warranty� � � � � � � � � � � � � � � � � � � � � � � 19

6 Disposal Instruction � � � � � � � � � � � � � � � 19

Table of Contents

Danfoss ECtemp Touch

3Installation Guide

• An installation wizard with room/oor type-specic

setup.

• Support for multiple frame systems.

• Compatible with several 3rd party NTC sensors.

• Thermostat settings can be specied before instal-

lation and imported to the thermostat using a

web-generated code, or copied from a thermostat in a

similar installation.

• Smart access to thermostat settings after installa-

tion by using a web code interface for easy setup or

remote troubleshooting.

More information on this product can also be found at:

electricheating�danfoss�com

1�1 Technical Specications

Operation voltage 220-240 V~, 50/60 Hz

Standby power consumption Max. 0.40 W

Relay:

Resistive load

Inductive load

Max. 16 A / 3680 W @ 230 V

cos φ= 0.3 Max. 1 A

Sensing units NTC 6.8 kΩ at 25°C

NTC 10 kΩ at 25°C

NTC 12 kΩ at 25°C

NTC 15 kΩ at 25°C (Default)

NTC 33 kΩ at 25°C

NTC 47 kΩ at 25°C

Danfoss ECtemp Touch

Installation Guide4

Sensing values:

(Default NTC 15 K)

0°C

20°C

50°C

42 kΩ

18 kΩ

6 kΩ

Control PWM (Pulse Width Modulation)

Ambient temperature 0° to +30°C

Frost protection temperature 5°C to +9°C (default 5°C)

Temperature range Room temperature: 5-35°C.

Floor temperature: 5-45°C.

Max. oor: 20-35°C (if unrecov-

erable seal is broken then up to

45°C). Min. oor: 10-35°C, only

with combination of room and

oor sensor.

Sensor failure monitoring The thermostat has a built-in

monitoring circuit, which will

switch o the heating if the

sensor is disconnected or short-

circuited

Cable specication max. 1x4 mm2or 2x2,5 mm2

Ball pressure test temperature 75°C

Pollution degree 2 (domestic use)

Controller type 1C

Software class A

Storage temperature -20°C to +65°C

Danfoss ECtemp Touch

5Installation Guide

IP class 21

Protection class Class II -

Dimensions 85 x 85 x 20-24 mm

(in-wall depth: 22 mm)

Weight 103 g

Electrical safety and Electro-Magnetic Compatibility for

this product is covered by the compliance with the EN/IEC

Standard“Automatic electrical controls for household and

similar use”:

• EN/IEC 60730-1 (general)

• EN/IEC 60730-2-9 (thermostat)

1�2 Safety Instructions

Make sure the mains supply to the thermostat is turned o

before installation.

Important: When the thermostat is used to control a oor

heating element in connection with a wooden oor or

similar material, always use a oor sensor and never set the

maximum oor temperature to more than 35°C.

Please also note the following:

• The installation of the thermostat must be done by an

authorized and qualied installer according to local

regulations.

Danfoss ECtemp Touch

Installation Guide6

• The thermostat must be connected to a power supply

via an all-pole disconnection switch.

• Always connect the thermostat to continuous power

supply.

• Do not expose the thermostat to moisture, water, dust,

and excessive heat.

2 Mounting Instructions

Please observe the following placement guidelines:

Place the thermostat at a suitable height on the wall

(typically 80-170cm.).

The thermostat should not be placed in wet rooms.

Place it in an adjacent room. Always place the ther-

mostat according to local regulation on IP classes.

Do not place the thermostat on the inner side of an

exterior wall.

Always install the thermostat at least 50 cm. from

windows and doors.

Danfoss ECtemp Touch

7Installation Guide

Do not place the thermostat in a way that it will be

exposed to direct sunlight.

Note: A oor sensor enables a more accurate

temperature control and is recommended in all oor

heating applications and mandatory under wooden

oors to reduce the risk of over-heating the oor.

• Place the oor sensor in a conduit in an appropriate place

where it is not exposed to sunlight or draft from door

openings.

• Equally distant and >2cm from two heating cables.

• The conduit should be ush with the oor surface -

countersink the conduit if necessary.

• Route the conduit to the connection box.

• The bending radius of the conduit must be min 50mm.

Danfoss ECtemp Touch

Installation Guide8

Follow the steps below to mount the thermostat:

1. Open the thermostat:

Important: Do NOT press on the display screen when

removing the front part.

Press your ngers under the side of the front part and

pull toward you:

2. Connect the thermostat according to the connection

diagram.

The screen of the heating cable must be connected to

the earth conductor of the power supply cable by

using a separate connector.

Note: Always install the oor sensor in a conduit in the

oor.

IP21

T30

Dtouch

Mains

220-240V

50-60 Hz

Maximum

Load 16 (1) A

Sensor

Standby maximum 0.4W

NTC N

Danfoss ECtemp Touch

9Installation Guide

3. Mount and reassemble the thermostat.

• Fasten the thermostat to a socket or an exterior wall

box by driving the screws through the holes in each

side of the thermostat.

• Put the frame on.

• Click the display module back in place.

Important: Do NOT press on the display screen when click-

ing the display module back in place.

Initially main supply the thermostat for 15 hours to fully

charge the battery. The current time and day is then kept

for 24 hours if mains supply is o. All other settings are

stored permanently.

3 Settings

3�1 Initial Settings

Initial settings must be specied when the unit is activated

for the rst time:

Danfoss ECtemp Touch

Installation Guide10

1. Use the arrows in the right

side of the screen to go to

your language, and press to

select it. Then press in the

upper right corner to

conrm.

2. Press the hour numbers and

use the < and > arrows to set

the hour. Press to conrm.

3. Press the minutes numbers

and use the < and > arrows

to set the minutes. Press

to conrm. Press again to

go to the SET DATE screen.

4. Press the day, month and

year respectively and set the

date using the < and >

arrows and pressing to

conrm. When the date is

correct, press to conrm

on the SET DATE screen.

Andere Handbücher für ECtemp Touch

Inhaltsverzeichnis

Andere Danfoss Thermostat Handbücher

Danfoss

Danfoss BasicPlus2 WT-T Bedienungsanleitung

Danfoss

Danfoss ECtemp 610 Bedienungsanleitung

Danfoss

Danfoss BasicPlus2 WT-D Bedienungsanleitung

Danfoss

Danfoss Living Eco Bedienungsanleitung

Danfoss

Danfoss RET1001M Bedienungsanleitung

Danfoss

Danfoss RT 14L Bedienungsanleitung

Danfoss

Danfoss ECL Comfort 210 Bedienungsanleitung

Danfoss

Danfoss ECL Comfort 210 Bedienungsanleitung

Danfoss

Danfoss TP4000 Range Bedienungsanleitung

Danfoss

Danfoss BasicPlus2 WT-DM Bedienungsanleitung

Danfoss

Danfoss living connect Bedienungsanleitung

Danfoss

Danfoss TP5000 si range Bedienungsanleitung

Danfoss

Danfoss DEVIreg 610 Bedienungsanleitung

Danfoss

Danfoss ECtemp Next Plus Bedienungsanleitung

Danfoss

Danfoss FH-CWT Bedienungsanleitung

Danfoss

Danfoss 088L5130 Bedienungsanleitung

Danfoss

Danfoss BasicPlus2 Bedienungsanleitung

Danfoss

Danfoss SET3M Montageanleitung

Danfoss

Danfoss REP24CO Bedienungsanleitung

Danfoss

Danfoss TP75 Bedienungsanleitung

Danfoss

Danfoss KP Series Bedienungsanleitung

Danfoss

Danfoss Icon Master Controller 24 V Bedienungsanleitung

Danfoss

Danfoss TP5001 series Bedienungsanleitung

Danfoss

Danfoss TP5001 series Gebrauchsanweisung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung