Danfoss ECtemp Touch Bedienungsanleitung

Danfoss ECtemp Touch

Electronic Intelligent Timer

Thermostat

Installation Guide

electricheating.danfoss.com

Danfoss ECtemp Touch

Installation Guide2

1 Introduction

The Danfoss ECtemp Touch is an electronic programmable

timer thermostat used for controlling electrical ﬂoor heat-

ing elements. The thermostat is designed for ﬁxed instal-

lation only and can be used for both direct heating of the

entire room and for comfort heating of the ﬂoor. Among

others, the thermostat has the following features:

• A touchscreen display with backlight.

• An easy-to-follow menu-driven programming and

operation.

1 Introduction . . . . . . . . . . . . . . . . . . . . . 2

1.1 Technical Speciﬁcations . . . . . . . . . . . 3

1.2 Safety Instructions . . . . . . . . . . . . . . . 5

2 Mounting Instructions . . . . . . . . . . . . . . . 6

3 Settings . . . . . . . . . . . . . . . . . . . . . . . . 9

3.1 Initial Settings. . . . . . . . . . . . . . . . . . 9

3.2 Forecast . . . . . . . . . . . . . . . . . . . . 13

3.3 Window Open . . . . . . . . . . . . . . . . 15

3.4 Maximum Floor Temperature . . . . . . . 16

4 Symbols . . . . . . . . . . . . . . . . . . . . . . . 19

5 Warranty. . . . . . . . . . . . . . . . . . . . . . . 20

6 Disposal Instruction . . . . . . . . . . . . . . . 22

Table of Contents

Danfoss ECtemp Touch

3Installation Guide

• An installation wizard with room/ﬂoor type-speciﬁc

setup.

• Support for multiple frame systems.

• Compatible with several 3rd party NTC sensors.

• Thermostat settings can be speciﬁed before instal-

lation and imported to the thermostat using a

web-generated code, or copied from a thermostat in a

similar installation.

• Smart access to thermostat settings after installa-

tion by using a web code interface for easy setup or

remote troubleshooting.

More information on this product can also be found at:

electricheating.danfoss.com

1.1 Technical Speciﬁcations

Operation voltage 220-240 V~, 50/60 Hz

Standby power consumption Max. 0.40 W

Relay:

Resistive load

Inductive load

Max. 16 A / 3680 W @ 230 V

cos φ= 0.3 Max. 1 A

Sensing units NTC 6.8 kΩ at 25°C

NTC 10 kΩ at 25°C

NTC 12 kΩ at 25°C

NTC 15 kΩ at 25°C (Default)

NTC 33 kΩ at 25°C

NTC 47 kΩ at 25°C

Danfoss ECtemp Touch

Installation Guide4

Sensing values:

(Default NTC 15 K)

0°C

20°C

50°C

42 kΩ

18 kΩ

6 kΩ

Control PWM (Pulse Width Modulation)

Ambient temperature 0° to +30°C

Frost protection temperature 5°C to +9°C (default 5°C)

Temperature range Room temperature: 5-35°C.

Floor temperature: 5-45°C.

Max. ﬂoor: 20-35°C (if unrecov-

erable seal is broken then up to

45°C). Min. ﬂoor: 10-35°C, only

with combination of room and

ﬂoor sensor.

Sensor failure monitoring The thermostat has a built-in

monitoring circuit, which will

switch oﬀ the heating if the

sensor is disconnected or short-

circuited

Cable speciﬁcation max. 1x4 mm2or 2x2,5 mm2

Ball pressure test temperature 75°C

Pollution degree 2 (domestic use)

Controller type 1C

Software class A

Storage temperature -20°C to +65°C

Danfoss ECtemp Touch

5Installation Guide

IP class 21

Protection class Class II -

Dimensions 85 x 85 x 20-24 mm

(in-wall depth: 22 mm)

Weight 103 g

Electrical safety and Electro-Magnetic Compatibility for

this product is covered by the compliance with the EN/IEC

Standard “Automatic electrical controls for household and

similar use”:

• EN/IEC 60730-1 (general)

• EN/IEC 60730-2-9 (thermostat)

1.2 Safety Instructions

Make sure the mains supply to the thermostat is turned oﬀ

before installation.

Important: When the thermostat is used to control a ﬂoor

heating element in connection with a wooden ﬂoor or

similar material, always use a ﬂoor sensor and never set the

maximum ﬂoor temperature to more than 35°C.

Please also note the following:

• The installation of the thermostat must be done by an

authorized and qualiﬁed installer according to local

regulations.

Danfoss ECtemp Touch

Installation Guide6

• The thermostat must be connected to a power supply

via an all-pole disconnection switch.

• Always connect the thermostat to continuous power

supply.

• Do not expose the thermostat to moisture, water, dust,

and excessive heat.

2 Mounting Instructions

Please observe the following placement guidelines:

Place the thermostat at a suitable height on the wall

(typically 80-170cm.).

The thermostat should not be placed in wet rooms.

Place it in an adjacent room. Always place the ther-

mostat according to local regulation on IP classes.

Do not place the thermostat on the inner side of an

exterior wall.

Always install the thermostat at least 50 cm. from

windows and doors.

Danfoss ECtemp Touch

7Installation Guide

Do not place the thermostat in a way that it will be

exposed to direct sunlight.

Note: A ﬂoor sensor enables a more accurate

temperature control and is recommended in all ﬂoor

heating applications and mandatory under wooden

ﬂoors to reduce the risk of over-heating the ﬂoor.

• Place the ﬂoor sensor in a conduit in an appropriate place

where it is not exposed to sunlight or draft from door

openings.

• Equally distant and >2cm from two heating cables.

• The conduit should be ﬂush with the ﬂoor surface -

countersink the conduit if necessary.

• Route the conduit to the connection box.

• The bending radius of the conduit must be min 50mm.

Danfoss ECtemp Touch

Installation Guide8

Follow the steps below to mount the thermostat:

1. Open the thermostat:

Important: Do NOT press on the display screen when

removing the front part.

Press your ﬁngers under the side of the front part and

pull toward you:

2. Connect the thermostat according to the connection

diagram.

The screen of the heating cable must be connected to

the earth conductor of the power supply cable by

using a separate connector.

Note: Always install the ﬂoor sensor in a conduit in the

ﬂoor.

IP21

T30

Dtouch

Mains

220-240V

50-60 Hz

Maximum

Load 16 (1) A

Sensor

Standby maximum 0.4W

NTC N

Danfoss ECtemp Touch

9Installation Guide

3. Mount and reassemble the thermostat.

• Fasten the thermostat to a socket or an exterior wall

box by driving the screws through the holes in each

side of the thermostat.

• Put the frame on.

• Click the display module back in place.

Important: Do NOT press on the display screen when click-

ing the display module back in place.

Initially main supply the thermostat for 15 hours to fully

charge the battery. The current time and day is then kept

for 24 hours if mains supply is oﬀ. All other settings are

stored permanently.

3 Settings

3.1 Initial Settings

Initial settings must be speciﬁed when the unit is activated

for the ﬁrst time:

Danfoss ECtemp Touch

Installation Guide10

1. Use the arrows in the right

side of the screen to go to

your language, and press to

select it. Then press in the

upper right corner to

conﬁrm.

2. Press the hour numbers and

use the < and > arrows to set

the hour. Press to conﬁrm.

3. Press the minutes numbers

and use the < and > arrows

to set the minutes. Press

to conﬁrm. Press again to

go to the SET DATE screen.

4. Press the day, month and

year respectively and set the

date using the < and >

arrows and pressing to

conﬁrm. When the date is

correct, press to conﬁrm

on the SET DATE screen.

Andere Handbücher für ECtemp Touch

Inhaltsverzeichnis

Andere Danfoss Thermostat Handbücher

Danfoss

Danfoss TP5000 si range Bedienungsanleitung

Danfoss

Danfoss DEVI DEVIreg Opti Bedienungsanleitung

Danfoss

Danfoss RT51 Bedienungsanleitung

Danfoss

Danfoss 088U0210 Bedienungsanleitung

Danfoss

Danfoss CF-RP 088U0211 Bedienungsanleitung

Danfoss

Danfoss CET2000B-RF Bedienungsanleitung

Danfoss

Danfoss TS715Si Bedienungsanleitung

Danfoss

Danfoss KPU 61 Bedienungsanleitung

Danfoss

Danfoss ECtemp Smart Bedienungsanleitung

Danfoss

Danfoss ECL Comfort 210 Bedienungsanleitung

Danfoss

Danfoss FH-CWP Bedienungsanleitung

Danfoss

Danfoss Link DBR Bedienungsanleitung

Danfoss

Danfoss ECL Comfort 210 Bedienungsanleitung

Danfoss

Danfoss TP7000 Series Bedienungsanleitung

Danfoss

Danfoss 140F1080 Bedienungsanleitung

Danfoss

Danfoss KP 61 Bedienungsanleitung

Danfoss

Danfoss FH-CWD Bedienungsanleitung

Danfoss

Danfoss FP735Si Bedienungsanleitung

Danfoss

Danfoss TP9000 Si Bedienungsanleitung

Danfoss

Danfoss HC6000 Bedienungsanleitung

Danfoss

Danfoss 088U0212 Bedienungsanleitung

Danfoss

Danfoss DEVI DEVIreg Touch Bedienungsanleitung

Danfoss

Danfoss TP4 Montageanleitung

Danfoss

Danfoss MTD Montageanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung