Danfoss TS715 Si Bedienungsanleitung
6
Systems with dial thermostats continued
Operating instructions for the underfloor heating timeclocks
TS715 – Single-channel timeclock
Nu-Heat supplies Danfoss TS715 single-channel programmable floor heating
timeclocks to control the underfloor heating system.
Room zone temperatures are individually controlled by simple dial-type thermostats.
Please remember that underfloor heating takes longer to warm up and cool down
than conventional radiators and the timeclock settings should reflect this.
Ensure that each timeclock is set to your requirements as follows:-
Programming – day and time
1. Open the cover. Press prog to enter
programming mode.
2. Press day to select day of the week.
Repeat until correct day is displayed.
3. Use +or -to adjust the time until
correct.
SELECT
PROG
NEXT ON/OFF
+
–
DAY
COPY
R/S
12:00
PM
MO
ON
OFF
AUTO
ALL DAY
+1HR
MAN
SELECT
PROG
NEXT ON/OFF
+
–
DAY
COPY
R/S
12:00
PM
TU
SET TIME
+1HR
MAN
SELECT
PROG
NEXT ON/OFF
+
–
DAY
COPY
R/S
12:02
PM
MO
SET TIME
+1HR
MAN
SELECT
PROG
NEXT ON/OFF
+
–
DAY
COPY
R/S
12:00
PM
MO
SET TIME
+1HR
MAN
SELECT
PROG
NEXT ON/OFF
+
–
DAY
COPY
R/S
4:30
AM
MO
SET TIME
1
ON
+1HR
MAN
SELECT
PROG
NEXT ON/OFF
+
–
DAY
COPY
R/S
8:00
AM
MO
SET TIME
2
OFF
+1HR
MAN
SELECT
PROG
NEXT ON/OFF
+
–
DAY
COPY
R/S
11:15
MO
SET TIME
6
OFF
PM
+1HR
MAN
SELECT
PROG
NEXT ON/OFF
+
–
DAY
COPY
R/S
12:30
PM
TU
SET TIME
4
OFF
+1HR
MAN
SELECT
PROG
NEXT ON/OFF
+
–
DAY
COPY
R/S
11:15
PM
FR
SET TIME
6
OFF
+1HR
MAN
Programming – on/off times
4. Press prog to enter on/off
programming mode.
5. Use +or -to adjust the 1st on time,
(setting number 1).
6. Press next to step to 1st off time,
(setting number 2).
7. Use +or -to adjust the 1st off time,
(setting number 2).
8. Press next and repeat steps 5 – 7
until all on/off times are
programmed to suit.
9. If unit is pre-set for 24 hour operation
go to step 13, If a different cycle is
required, alter the internal pins and
continue with step 10 (see opposite).
10. Press day to advance to the next day
if different programming from the
previous day is required.
If the programme is the same, go
to step 11.
11. Press the copy button to copy the
previous day’s programming to the
current day.
12. Repeat steps 10 – 11 until all days
are programmed.
13. Press prog to return to run mode.
7
Operation
If the colon is blinking the unit is in run mode. It will
automatically switch the underfloor heating on and off at
the times set. However, useful overrides are provided which
enable the user to to make temporary changes to the on/off
times without re-programming the unit.
Manual overrides
When in off, auto or allday modes the +1hr button can be
used to switch from off to on for just one hour, or to extend
an existing period by one hour. This will be cancelled by
pressing the +1hr button again, pressing the man button
or when the next on programme is reached.
When in auto or allday modes pressing the man (manual)
button will switch from on to off, and vice versa. This override
will only last until the next programmed change, when the
automatic programming will resume, or until the button is
pressed again.
When the above overrides are selected a bar appears in the
display against the appropriate legend.
Reset
Should the timeswitch be disconnected from the mains a
small battery symbol will blink on the left of the display. After
the second midnight (between 24 and 48 hours) the display
will go blank and settings will be lost. When mains power is
restored it is recommended that the unit be reset by inserting
a non-metallic object such as a matchstick in the r/s hole
under the flap. This will restore the factory settings with the
time at 12:00 and Monday (mo) selected. The output will be
off. Note that the colon will be blinking, meaning that the unit
is in run mode and will switch on and off according to the
factory programming until reset.
Choice of 12- or 24-hour clock
At any time whilst in run mode the time displayed can be
toggled between a 12-hour clock with an am/pm indicator
or a 24-hour clock by pressing and holding both day and
next on/off buttons for 1.5 seconds.
G.M.T./B.S.T.
To change from Greenwich Mean Time to British Summer
Time and vice versa while in run mode: press and hold
the +button to add one hour in Spring, or the –button to
put the clock back one hour in Autumn.
Factory pre-set programme
The unit will be pre-set to 7-day/24-hour mode; this can
be altered by moving the pins under the backplate. Firstly
remove the screws under the unit and remove the front face.
There are three operating modes available:
124 hour operation; the same programme
each day,
25-day/2-day operation; different
programmes for weekdays and weekends,
37-day operation; different programmes for
each day.
Set the pins as shown for the operating mode required.
The pre-set factory on/off times can be reinstated by pressing
the recessed r/s button with a non-metallic object such as a
matchstick. Please remember that underfloor heating takes
longer to warm up and cool down than conventional radiators
and the heat settings should reflect this. The factory settings
are unlikely to be appropriate.
1 2 3 4
1 2 3 4
1 2 3 4
Selecting the operating mode
Behind the flap is the red select button; each press changes the operating
mode as follows:
on The output is constantly on.
off The output is constantly off unless +1hr is pressed.
auto The output switches on and off to the set programme.
allday The output switches on at setting 1 and stays on until setting 6.
SELECT
PROG
NEXT ON/OFF
+
–
DAY
COPY
R/S
12:45
AM
MO
ON
OFF
AUTO
ALL DAY
+1HR
MAN
Andere Handbücher für TS715 Si
4
Inhaltsverzeichnis
Andere Danfoss Thermostat Handbücher
Danfoss
Danfoss DEVIreg 610 Bedienungsanleitung
Danfoss
Danfoss Link FT Bedienungsanleitung
Danfoss
Danfoss TP75M Bedienungsanleitung
Danfoss
Danfoss Icon Master Bedienungsanleitung
Danfoss
Danfoss TP5001RF Bedienungsanleitung
Danfoss
Danfoss ECL Comfort 210 Bedienungsanleitung
Danfoss
Danfoss TPOne-M Bedienungsanleitung
Danfoss
Danfoss RAS-D2 Combi Bedienungsanleitung
Danfoss
Danfoss RET2001RF Bedienungsanleitung
Danfoss
Danfoss ECL Comfort 210 Bedienungsanleitung
Danfoss
Danfoss Devireg 535 Gebrauchsanweisung
Danfoss
Danfoss TP75-RF Bedienungsanleitung
Danfoss
Danfoss ECL Comfort 310, P318 Bedienungsanleitung
Danfoss
Danfoss DEVIreg Smart Bedienungsanleitung
Danfoss
Danfoss TP5000 si range Bedienungsanleitung
Danfoss
Danfoss ECL Comfort 210 Bedienungsanleitung
Danfoss
Danfoss CF-RS Bedienungsanleitung
Danfoss
Danfoss TS715 Si Montageanleitung
Danfoss
Danfoss GreenCon RC-T2 Bedienungsanleitung
Danfoss
Danfoss ECL Comfort 310 Bedienungsanleitung
Beliebte Thermostat Handbücher anderer Marken
EWELLY
EWELLY EW-181 Bedienungsanleitung
Prolon
Prolon T1100 Montageanleitung
Computherm
Computherm Q20 Bedienungsanleitung
Heatmiser
Heatmiser neoStat Bedienungsanleitung
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung
