Datamax M-Class Mark II Bedienungsanleitung
M-Class Mark II
Maintenance Manual
Copyright Information:
CG Triumvirate is a trademark of Agfa Corporation.
CG Times based upon Times New Roman under license from the Monotype Corporation.
Windows is a registered trademark of the Microsoft Corporation.
All other brand and product names are trademarks, service marks, registered trademarks, or registered
service marks of their respective companies.
Firmware (Software) Agreement:
The enclosed Firmware (Software) resident in the Printer is owned by Licensor or its suppliers and is
licensed for used only on a single printer in the user’s Trade or Business. The User agrees not to, and
not to authorize or permit any other person or party to, duplicate or copy the Firmware or the
information contained in the non-volatile or programmable memory. The firmware (Software) is
protected by applicable copyright laws and Licensor retains all rights not expressly granted. In no event
will Licensor or its suppliers be liable for any damages or loss, including direct, incidental, economic,
special, or consequential damages, arising out of the use or inability to use the Firmware (Software).
CAUTION
Lithium Battery: There is a danger of explosion or fire if the battery is incorrectly
replaced. Replace only with the same or equivalent type recommended by the
manufacturer. Discard used batteries according to the manufacturer’s instructions.
Information in this document is subject to change without notice and does not represent a commitment on
the part of Datamax-O’Neil. No part of this manual may be reproduced or transmitted in any form or by
any means, for any purpose other than the purchaser's personal use, without the expressed written
permission of Datamax-O’Neil.
All rights reserved.
Part Number 88-2347-01 Rev. B
COPYRIGHT © 2010, DATAMAX-O’NEIL
i
Contents
1 Overview
2 Adjustments and Maintenance
3 Troubleshooting
4 Removal and Replacement
ii
i
1
Overview
1.0 Introduction........................................................................................1
1.1 About this Printer.................................................................................2
ii
Overview
1-1
1.0 Introduction
This manual, which primarily includes technical information relating to the electrical and
mechanical components, is intended for use by qualified service personnel in the
maintenance and repair of M-Class Mark II printers. For related information, refer to the
following documents, available for download at http://www.datamax-oneil.com/
For operating information, reference the Operator’s Manual (part number 88-2340-01).
For software information, reference the Class Series 2 Programmer’s Manual (part
number 88-2341-01).
Important Information:
In this manual, the exclamation point inside an equilateral triangle is intended
to alert the technician to the presence of important operating, maintenance or
servicing information. Always, as with all electrical equipment, follow basic
safety precautions to avoid personal injury or printer damage.
Overview
1-2
1.1 About this Printer
The following drawing illustrates the basic exterior components and controls of the printer.
The model number can be found on the Serial Tag affixed to the rear of the unit. Use this
model number when referencing specific information within this manual. (Because optional
items are not present on all models, certain printer configurations may not appear in some
of the illustrations in this manual.)
Centerplate
Access Cover
Front Panel
Ribbon Take-Up Hub
Ribbon Supply Hub
Media Supply Assembly
(Hanger or Hub)
Internal Rewinder
Printhead Assembly
Ribbon Idler
Media Sensor
Printhead Latch
Media Guide
Fascia
Media Idler
i
2Adjustments and Maintenance
2.0 Introduction........................................................................................ 1
2.1 Maintenance ....................................................................................... 1
2.1.1 Cleaning the Printhead ................................................................ 2
2.1.1.1 Cotton Swab Procedure.................................................. 3
2.1.1.2 Cleaning Card Procedure ................................................4
2.1.1.3 Cleaning Film Procedure................................................. 5
2.1.2 Cleaning the Media Sensor........................................................... 6
2.1.3 Cleaning the Platen..................................................................... 6
2.1.4 Cleaning the Ribbon Path............................................................. 7
2.2 Media Sensor Calibration ...................................................................... 9
2.2.1 Calibrating Non-Display Models..................................................... 9
2.2.1.1 Automatic Calibration..................................................... 9
2.2.1.2 Manual Calibration....................................................... 10
2.2.2 Calibrating Display-Equipped Models............................................ 11
2.2.2.1 Quick Calibration......................................................... 11
2.2.2.2 Standard Calibration.................................................... 12
2.2.2.3 Advanced Entry Calibration........................................... 15
2.3 Media Width Adjustment..................................................................... 21
2.4 Printhead Burn Line Adjustment........................................................... 22
2.5 Printhead Pressure Adjustment............................................................ 23
ii
2.6 Ribbon Path Alignment ....................................................................... 23
2.7 Darkness Adjustment ......................................................................... 26
2.8 Downloading Firmware and Fonts......................................................... 26
2.9 Resetting the Printer .......................................................................... 27
2.9.1 Non-Display Models................................................................... 27
2.9.2 Display-Equipped Models ........................................................... 27
2.10 Printhead Voltage Adjustment.............................................................. 28
Andere Handbücher für M-Class Mark II
10
Inhaltsverzeichnis
Andere Datamax Drucker Handbücher
Datamax
Datamax M-Class Bedienungsanleitung
Datamax
Datamax A-Class A-4212 Service-Handbuch
Datamax
Datamax I-Class Mark II Bedienungsanleitung
Datamax
Datamax E-Class Mark II Bedienungsanleitung
Datamax
Datamax E-Class Mark III Bedienungsanleitung
Datamax
Datamax Workstation w1110 Bedienungsanleitung
Datamax
Datamax MP Compact4 Mark II Bedienungsanleitung
Datamax
Datamax A-Class Mark II Bedienungsanleitung
Datamax
Datamax Apex 3 Bedienungsanleitung
Datamax
Datamax M-Class Mark II M-4206 Bedienungsanleitung
Datamax
Datamax h-class h-8308p Bedienungsanleitung
Datamax
Datamax Mark II M-4210 Bedienungsanleitung
Datamax
Datamax MP-Nova4 DT Bedienungsanleitung
Datamax
Datamax E-Class Mark III Professional+ Bedienungsanleitung
Datamax
Datamax M-Class Mark II Series Bedienungsanleitung
Datamax
Datamax Apex 4 Bedienungsanleitung
Datamax
Datamax E-class E-3202 Bedienungsanleitung
Datamax
Datamax H-Class Bedienungsanleitung
Datamax
Datamax ANDES 3 Bedienungsanleitung
Datamax
Datamax Apex 3 Bedienungsanleitung
