DaVinci Hypermax OXYGEN Bedienungsanleitung

SET-UP

Instruction

MANUAL

QUICK START

set up & usage videos

(aim camera at this image to begin)

WARNING ⚠

DO NOT USE SYSTEM IF YOU HAVE

COPD and/or severe COPD

with CO2 retention.

(1) PVC Frame Top

(1) PVC Frame Bottom with

Base Plate & Hose Elbow

(4) PVC Long Frame Poles

(Separate Box)

(4) 1 lb Weights (Attached

to Frame Top) - Optional

(1) 900 Liter Oxygen Bag/Cylinder

(1) Red Capped Relief Valve

(Peep Valve)

(1) Mask & Strap

(1) Thin ¼” Supply Hose

(Concentrator to Cylinder)

(1) 10’ Breathing Hose

(Cylinder to Mask)

(1) Green Breathing Valve

(1) Inline Back Flow Valve

(1) Velcro Hose Holder

(1) Flexible “Gooseneck”

Long Arm Clip

PACKAGE CONTENTS

Congratulations on receiving your HyperMax

Oxygen System — atrue scientific breakthrough for

improving your health, immunity, endurance and

longevity. We created the HyperMax Oxygen

Wellness System to help people like you restore

and increase their body’s oxygen levels and greatly

improve their overall Health, Fitness and Well-Being.

This instruction manual will help you set up your

unit smoothly and easily, from start to ﬁnish, and

you’ll be on your way to 93% oxygen in no time.

davincimedicalusa.com

STEP

ONE

OXYGEN

CONCENTRATOR

davincimedicalusa.com

Start by unpacking the HyperMax Oxygen concentrator that was shipped to

you in a large and heavy box. First lay the box on its side, and carefully slide

the Oxygen concentrator unit out from the shipping container.

Then stand the HyperMax Oxygen concentrator back in its upright position.

CONTROL PANEL

davincimedicalusa.com

1. Select a location that allows the concentrator unit to draw in room air

without being restricted. Make sure that the unit is at least 4 inches

(10cm) away from any wall, furniture, or curtains that could impede

adequate airflow. Do not place the unit near any heat source.

2. Plug the power cord into an electrical outlet.

3. Connect the provided silicon tubing to port at top right rear of the

machine as shown in Image 1.

4. Press the power switch to the ON [I] position. The LED display screen will

illuminate.

5. Press the ON/OFF power button once to turn the unit on. The oxygen will

begin flowing from the unit immediately.

6. Adjust the flow by turning the knob on the top of the flow meter until the

ball is centered at 10. See Image 3 for knob reference.

7. When the oxygen concentrator is not in use, press the power switch to

the OFF [O] position.

Image 1 Image 2 Image 3

•Continuous Working Mode - By pressing the ON/OFF button, oxygen

will begin to flow from the oxygen concentrator, using a "continuous"

working state (will stay on until you manually turn it off). The LCD screen

will display the total usage time your generator has been used (like a car

odometer).

•Timer Working Mode - Once the oxygen has begun flowing, press the

"timing+" button - this will allow the unit to begin in the timed working

mode. Each time the "timing+" button is pressed, the preset time will be

increased by 10 minutes. The maximum preset time is 480 minutes. By

pressing the "timing-" button, the preset time will decrease, in

increments of 10 minutes.

davincimedicalusa.com

MODE OPTIONS

(Continuous and Timer)

The Da Vinci 10 LPM Oxygen Concentrator has two different mode options

available:

1. Set the oxygen timer for 90 minutes for the first time to completely fill

the bag.

2. If the bag is half full after your session, you will only need to set the

oxygen timer for 40 minutes to fill the bag.

3. To double or triple the speed at which your bag is filled, you would

simply add a second or third generator.

4. You may leave the oxygen generator running during your exercise

sessions.

davincimedicalusa.com

BAG FILLING TIPS

Next, set up the HyperMax frame located in the other large box you received.

After opening this box, take your mask out and set it to the side. Then remove

the entire HyperMax frame from the box as one unit. Once your frame is out

of the box, separate the top of the frame from the short colored poles used

for shipping, and then set this top frame to the side.

FRAME

SET-UP

STEP

TWO

davincimedicalusa.com

Locate the long, thin shipping tube you received from HyperMax. This

long tube contains the four poles you will need to complete the set up of

your HyperMax frame.

One at a time, you want to remove the short colored poles and set them

aside. These small poles are temporary and designed for shipping — but

the long black poles are used for the actual HyperMax frame.

Start by inserting each long pole, one at a time, into each hole at the base

of the frame. It’s important to make sure that you get all four rings on a side

of the Oxygen Bag/Cylinder onto a pole, and then repeat this step three more

times. Once you have all four poles in the frame bottom, with all four rings on

each pole, you will then push each pole down firmly into its proper fitting.

These poles will connect the bottom to the top of the frame.

FRAME

SET-UP

(CONT’D)

STEP

THREE

davincimedicalusa.com

Inhaltsverzeichnis

Andere DaVinci Medizinische Geräte Handbücher

DaVinci

DaVinci IQC Bedienungsanleitung

Beliebte Medizinische Geräte Handbücher anderer Marken

TekTone

TekTone Tek-CARE160 Bedienungsanleitung

NeuroMetrix

NeuroMetrix Quell 2.0 Bedienungsanleitung

AMT

AMT XLR8 Bedienungsanleitung

EDAN

EDAN SONOTRAX Pro Bedienungsanleitung

Restorative Therapies

Restorative Therapies RT300 Bedienungsanleitung

Gendex

Gendex Expert DC Bedienungsanleitung

Dexcowin

Dexcowin ADX4000W Bedienungsanleitung

Libelium

Libelium MySignals Bedienungsanleitung

Acelity

Acelity V.A.C.ULTA 4 Bedienungsanleitung

Caputron

Caputron ActivaDose II tDCS Bedienungsanleitung

Plinth 2000

Plinth 2000 93CDT Bedienungsanleitung

GE SENOGRAPHE 800T Bedienungsanleitung

GE Definium 5000 Bedienungsanleitung

Kanmed

Kanmed GE-1380 Bedienungsanleitung

Huntleigh

Huntleigh FD1 Bedienungsanleitung

Stryker

Stryker SPR Plus Bedienungsanleitung

Tobii Dynavox

Tobii Dynavox I-Series Bedienungsanleitung

S-Capepod

S-Capepod Evac Cocoon Bedienungsanleitung