DEFA REDARC SmartCharge 4A Bedienungsanleitung

SmartCharge

User Manual

10A

Product warnings

Save these instructions - this manual contains important

safety instructions.

Do not operate the battery charger unless you have read and

understood this manual and the charger is setup as per these

installation instructions.

1. Risk of explosive gases: Working in the vicinity of a

Lead-Acid battery is dangerous. Batteries generate

explosive gases during normal operation. For this reason,

it is of utmost importance that you follow the instructions

when installing and using the charger.

2. The Battery Charger should not be used by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge,

unless they are supervised or have been instructed on

how to use the appliance by a person responsible for their

safety. Children should be supervised to ensure that they

do not play with the Battery Charger.

3. Do NOT alter or disassemble the Battery Charger under

any circumstances. All faulty units must be returned

to REDARC for assessment. Incorrect handling or

reassembly may result in a risk of electric shock or

ﬁre and may void the unit warranty. The mains’ power

supply cord cannot be replaced. If the cord is damaged,

discontinue usage.

4. This charger is designed for use only with LEAD/ACID type

(both open and closed) batteries including AGM, GEL and

Lead Crystal types or LiFePO4batteries with appropriate

cell & battery protection; and for battery sizes as shown

on page 8. The charger should not be used for other

battery types or for charging non-rechargable batteries.

5. Check the manufacturer’s data for your battery and

ensure that the ‘Maximum’ voltage of the proﬁle

you select does not exceed the manufacturer’s

recommended maximum charging voltage.

6. Check the manufacturer’s data for your battery and

ensure that the ‘Continuous Current Rating’ of the charger

does not exceed the manufacturer’s recommended

maximum charging current.

7. Batteries can emit explosive gases during normal

charging. Avoid sparks in the immediate area and always

provide proper ventilation during charging.

8. Connect the charger’s positive clamp to the positive

terminal on the battery. Connect the negative clamp to

the chassis of the vehicle away from petrol pipes. Then

connect to AC mains and turn the charger ON.

9. After charging, turn oﬀ the charger and disconnect from

the mains’ power supply. The negative and positive

terminals can then be disconnected.

10. This charger includes high-strength magnets and should

not be placed in close proximity to magnetic storage

devices such as computer hard drives or tape media.

Setting up the Charger

1. Connect the charger’s POSITIVE clamp to

the POSTIVE terminal on the battery.

2. Connect the Charger’s NEGATIVE clamp to

the chassis of the vehicle, away from heat

sources or petrol pipes.

3. Plug the mains plug into a 240VAC mains

power socket and turn the charger ON.

Operation

DEFA SmartChargers provide battery charging

for a range of vehicles and equipment such as

cars, motorbikes, 4x4s, recreational vehicles,

lawnmowers, jet skis and boats etc.

Battery Type

Lead acid, AGM, Gel, Lead Crystal and LiFePO4

batteries included.

Pre Analysis

The charger checks if the battery is correctly

connected. The battery’s voltage (V) and total

capacity (Ah) is measured to determine the correct

settings for charging.

Battery voltage Battery status LED indication

>12.65V 95–100% All segments on

12.55V–12.65V 80% 4 segments on

12.45V–12.55V 60% 3 segments on

12.35V–12.45V 40% 2 segments on

2.0V–12.35V 0-20% 1 segment on

Charging Proﬁle

The charger begins charging with a constant current

until the voltage reaches 14.4V (at 25°C). The

charge voltage is then held constant at 14.4V and

the charging current is reduced until it is below a

predeﬁned level. The charge voltage then drops to

13.8V, before the long-term charging stage starts.

During charging, the battery charge is shown by the

number of LEDs illuminated; The blinking segment

above these LEDs indicates active charging. Once

full charge is reached, all 5 LED segments will

remain illuminated. If the measured battery voltage

is below 2.0V, the charger will enter Error Mode.

Post Analysis

The charger analyses the battery again after the

charging stage. If the charger detects an error in

the battery, the warning triangle will ﬂash. Post

analysis can detect batteries with a short circuit

in individual cells (this cannot be detected in the

Pre Analysis). If the battery’s voltage drops below

12.5V within 2 min, the charger will go into error

mode. The charging sequence will be stopped.

Long-term charging

After the battery is fully charged, the charger will

go in to Sleep Mode. This is indicated by all battery

LEDs slowly pulsating. This mode has a very low

power consumption.

After a week in Sleep Mode, the charger will wake

up and begin a new charging cycle. Alternatively

the charger will also resume charging if the battery

voltage drops below 12.6V.

Additional charger functionality

Temperature based voltage compensation

The charger automatically adjusts the charging

voltage to the correct level according to the

ambient temperature. The default ambient

temperature is 25°C. Voltage is reduced for

higher ambient temperatures and increased

for lower ambient temperatures by ±0.03V/°C.

Max temperature compensate charging voltage

is 15.3 V.

14.7V button

Some batteries require a higher charging voltage

than other batteries. If the 14.7V button is

activated the initial charging voltage will be 0.3V

higher than the standard level.

Before activating this button, the 14.7V charge

voltage requirement should be conﬁrmed. If a

battery requires this higher charge voltage, it will

be described on the battery.

Power Supply mode

Press and Hold the button until the LED shines

one by one in a regular bottom to the top cycle, the

charger will start power supply mode. In this mode,

the charger supply 13.6V.

If the output is short circuit or connected with

incorrect polarity in this mode, the charger will go

into error mode. After resolving the error, press the

power button to turn oﬀ the charger, then restart

the charger (go to charge or power supply mode).

Automatic restart after mains supply

interruption

If the mains supply is temporarily interrupted, the

charger will continue charging when the power

supply returns.

Safety features

• Incorrect polarity protection

• Spark protection

• Short circuit protection

• Over-current protection

• Over-temperature protection

• Over-voltage protection

• Low voltage protection

Approvals

Safety:

EN 60335-1: 2012

EN 60335-2-29: 2004+A2:2010

EN 62233:2008

EMC (emissions):

EN 61204-3:2000

EN 61000-3-3:2008

EN 61000-3-2:2006+A1:2009+A2:2009

EMC (immunity):

EN 61204-3:2000

Technical data

Type 4A

(SBC1204)

(SBC1206)

Battery size (V/Ah) 12/2-110 12/10-150

Input (VAC/Hz) 230 /50-60

Power Consumption (W) 60 115

Output Voltage (V) 14.4/14.7

Output current (A) 4 (max) 6 (max)

Reverse current (mA) I drain <1

IP class (IP) 65

Type 8A

(SBC1208)

10A

(SBC1210)

Battery size (V/Ah) 12/20-200 12/30-250

Input (VAC/Hz) 230 /50-60

Power Consumption (W) 132 175

Output Voltage (V) 14.4/14.7

Output current (A) 8 (max) 10 (max)

Reverse current (mA) I drain <1

IP class (IP) 65

Over the last three decades our company

has established a reputation as the power

conversion specialist.

A 100% Australian-owned company, we have met

the needs of customers in transport and other

industries through exciting, innovative thinking.

We believe in total customer satisfaction and

practice this by oﬀering our customers:

• Technical advice free of jargon and free of

charge

• Prompt turnaround of orders throughout

Australia and globally

• Friendly, personalised, professional service

and product support

In the unlikely event that a technical issue

arises with a Redarc product, customers are

encouraged to initially contact the Redarc

Technical Support Team on (08) 8322 4848 or

[email protected] for prompt and eﬃcient

diagnosis and product support.

Our goods come with guarantees that cannot be

excluded under the Australian Consumer Law. You

are entitled to a replacement or refund for a major

failure and compensation for any other reasonably

foreseeable loss or damage. You are also entitled

to have the goods repaired or replaced if the goods

fail to be of acceptable quality and the failure does

not amount to a major failure.

The beneﬁts of this Warranty are in addition to

other rights and remedies available at law in

respect of the Products and shall not derogate

from any applicable mandatory statutory

provisions or rights under the Australian Consumer

Law.

Redarc Electronics Pty Ltd atf the Redarc Trust

trading as Redarc Electronics (“Redarc”) oﬀers

a warranty in respect of its Products where the

Products are purchased from an authorised

distributor or reseller of Redarc by a person

(“Purchaser”), on the terms and conditions, and

for the duration, outlined below in this document

(“Warranty”).

1. In this Warranty, the term Products means:

1.1 all products manufactured or supplied by

Redarc (excluding its solar products which

are covered by Redarc’s Solar Product

Warranty); and

1.2 any component of or accessory for any

product in clause 1.1 manufactured or

supplied by Redarc.

Oﬀer and duration of product warranties

2. Redarc warrants that its Products will be free,

under normal application, installation, use and

service conditions, from defects in materials and

workmanship aﬀecting normal use, for 5 years from

the date of purchase (Warranty Period).

3. Where a Product malfunctions or becomes

inoperative during the Warranty Period, due to a

defect in materials or workmanship, as determined

by Redarc, then subject to further rights conferred

by the Australian Consumer Law on the Purchaser,

Redarc will, in exercise of its sole discretion, either:

3.1 repair the defective Product;

3.2 replace the defective Product; or

3.3 provide a refund to the Purchaser for the

purchase price paid for the defective

Product,

without charge to the Purchaser.

4. The warranty given by Redarc in clause 3 covers

the reasonable costs of delivery and installation of

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere DEFA Akkuladegerät Handbücher

DEFA

DEFA Solid Bedienungsanleitung

DEFA

DEFA WorkShopCharger 25A Bedienungsanleitung

DEFA

DEFA SmartCharge 6A Bedienungsanleitung

DEFA

DEFA CLU MK1 Bedienungsanleitung

DEFA

DEFA eRange ACC 710346 Bedienungsanleitung

DEFA

DEFA 125A Bedienungsanleitung

DEFA

DEFA MultiCharger 1x35A Bedienungsanleitung

DEFA

DEFA MultiCharger 1x20A Bedienungsanleitung

DEFA

DEFA ShowroomCharger 32A Bedienungsanleitung

DEFA

DEFA WorkShopCharger 35A Bedienungsanleitung

DEFA

DEFA WorkshopCharger DWSC125 Bedienungsanleitung

DEFA

DEFA PowerSystems 1x15 Bedienungsanleitung

DEFA

DEFA MultiCharger 1205R Flex Bedienungsanleitung

DEFA

DEFA MultiCharger 1203 Handbuch

DEFA

DEFA MultiCharger Bedienungsanleitung

DEFA

DEFA MultiCharger 1x12A Bedienungsanleitung

DEFA

DEFA MultiCharger 40A 24V Bedienungsanleitung

DEFA

DEFA Solid Bedienungsanleitung

DEFA

DEFA REDARC SBC1230-S Bedienungsanleitung

DEFA

DEFA MultiCharger 1x7 Bedienungsanleitung

DEFA

DEFA 1204R Flex Bedienungsanleitung

DEFA

DEFA WorkShopCharger 35A Bedienungsanleitung

DEFA

DEFA SmartCharge 701515 Bedienungsanleitung

DEFA

DEFA MultiCharger 1210 Flex Bedienungsanleitung

Beliebte Akkuladegerät Handbücher anderer Marken

AA Portable Power Corp

AA Portable Power Corp Universal Smart Charger Bedienungsanleitung

Enelion

Enelion Vertica Bedienungsanleitung

RCA

RCA CHU6 Bedienungsanleitung

ANSMANN

ANSMANN ALCT 6/24-10 Bedienungsanleitung

Hitachi

Hitachi UC 18YRSL Fehlerbehebungshandbuch

Olympus

Olympus B-20 LPC Bedienungsanleitung

Exibel

Exibel ZH1708143 Bedienungsanleitung

Lenmar

Lenmar Mach 1 Bedienungsanleitung

CTEK

CTEK MXS 5.0 Bedienungsanleitung

ABB

ABB HT842379 Bedienungsanleitung

Nitecore

Nitecore Superb Charger SC4 Bedienungsanleitung

Renogy

Renogy RBC2125DS-21W Bedienungsanleitung

Braun

Braun BWC02M Bedienungsanleitung

CTEK

CTEK MXS 3.6 Bedienungsanleitung

Black & Decker

Black & Decker BDV090 Bedienungsanleitung

Trinity

Trinity DPD Bedienungsanleitung

Hulkman

Hulkman Sigma 1 Bedienungsanleitung

IKEA

IKEA koppla Bedienungsanleitung