DEFA CLU MK1 Bedienungsanleitung

1DEFA CLU MK1 - Quick Guide IVersion 1.1

CLU®MK1 - Quick Guide

1 |INSTALL THE CHARGING STATION

2 |BUS COMMUNICATION WIRING

3 |INSTALL THE CLU

4 |CONFIGURATION

5 |COMPLETE THE INSTALLATION

6 |LABELING

DEFA CLU MK1 - Quick Guide IVersion 1.12 3DEFA CLU MK1 - Quick Guide IVersion 1.1

Connect all charge points in

the same way:

Brown = L1, Black = L2,

Grey = L3, Blue = N

Create a xed phase

rotation at the output of

the fuses, or terminal

blocks, one rotation-step

per connected charge

point.

All phases may be

distributed with a regular

“L1-L2-L3-N” bus bar

suitable for 4-pole DIN

block devices.

* The CPPS is a datasheet which describes how phase distribution, addresses etc. in a CLU facility must

be congured. It is includet with every CLU conguration and distributed by DEFA

1 IInstalling the charging station

Install the charging stations in accordance with the Charge Point Parameter

Settings (CPPS)*.

Use a connection pattern with phase rotation to ensure an even load distribution

among the phases.

SINGLE PHASE CHARGING ON

A TN NETWORK:

SINGLE PHASE CHARGING ON

A IT NETWORK:

PHASE ROTATION FOR THREE PHASE CHARGING ON A TN NETWORK:

Addr.

L1 N L2 N L3 N L1 N L2 N L3 N

Addr.

L1 L2 L3 L1 L2 L3 L1 L2 L3 L1 L2 L3

Addr.

L1 L2 L3 N L1 L2 L3 N L1 L2 L3 N

L1-L2-L3-N L2-L3-L1-N

L3-L1-L2-N

L2-L3-L1-NL1-L2-L3-N

DEFA CLU MK1 - Quick Guide IVersion 1.14 5DEFA CLU MK1 - Quick Guide IVersion 1.1

Connect the charging stations to the CLU

using a daisy chain topology.

The bus requires at least 3

conductors. 2 signal wires (A and

B) and 1 ground reference (M).

Use the connector inside the wall-

box to link the upstream and down-

stream charge points to the network.

Choose a colour code for each

terminal (A, B and M). Make sure

A and B are the same twisted pair.

Use the same colours throughout the

network to minimize the risk

of incorrect wiring.

2 IBus communication wiring

Use CAT5/6 for bus wiring. Alternatively, a similar twisted pair cable can also

be used.

Make sure the total length of the communication cable does not exceed

150 meters.

Use one bus to connect controllers and RFID readers to the CLU. The energy

meters requires a separate bus connection.

WHERE TO CONNECT THE

COMMUNICATION WIRING:

HOW TO CONNECT THE CLU NETWORK:

HOW TO CONNECT THE BUS:

eRange Uno with front lid open

eRange Duo with front lid open

BMABMA

CONTROL/RFID ENERGY METERCONTROL/RFID ENERGY METER

BUS IN BUS OUT

BUS OUTBUS IN

CONTROL/RFID ENERGY METERCONTROL/RFID ENERGY METER

BMABMA

CONTROL/RFID ENERGY METERCONTROL/RFID ENERGY METER

BUS IN BUS OUT

BUS OUTBUS IN

CONTROL/RFID ENERGY METERCONTROL/RFID ENERGY METER

2 4

CONTROL/RFID

CONTROL/RFID ENERGY METER

BUS OUTBUS IN

CONTROL/RFID ENERGY METER

BUS OUTBUS IN

CONTROL/RFID ENERGY METER

BUS OUTBUS IN

CONTROL/RFID ENERGY METER

BUS OUTBUS IN

CONTROL/RFID ENERGY METERCONTROL/RFID ENERGY METER

AMBAMBAMBAMB

CONTROL METER CONTROL METER

AMBAMBAMBAMB

BUS OUT

BUS IN

eRange Duo with front lid open

Manufactured

until June 2019

Manufactured

from July 2019

eRange Duo with

lid open

eRange Uno with

lid open

DEFA CLU MK1 - Quick Guide IVersion 1.16 7DEFA CLU MK1 - Quick Guide IVersion 1.1

7 8 9 10 7 8 9 10

6 7 8 6 7 8

CONTROL/RFID ENERGY METER

BUS OUTBUS IN

CONTROL/RFID ENERGY METER

7 8 9 10 7 8 9 10

6 7 86 7 8

CONTROL/RFIDENERGY METER

BUS OUT

ENERGY METER

and/or

7 8 9 10 7 8 9 10

6 7 86 7 8

CONTROL/RFIDENERGY METER

BUS OUTBUS IN

ENERGY METER

and/or

Yellow B Terminal 9

Black M Treminal 10

Orange A Treminal 8

HOW TO CONNECT TO AN ENERGY METER IN THE CHARGING STATION: HOW TO CONNECT ENERGY METERS IN THE DISTRIBUTION BOARD:

THREE-PHASE ENERGY METER*

SINGLE-PHASE ENERGY METER*

The bus requires at least 3

conductors. 2 signal wires (A and

B) and 1 ground reference (M).

Use the connector inside the

wallbox to link the upstream and

down-stream charge points to the

network.

The energy meter requires the installing of a separate bus from the CLU

Choose a colour code for each

terminal (A, B and M). Make sure

A and B are the same twisted pair.

Use the same colours throughout

the network to minimize the risk

of incorrect wiring.

2 4

CONTROL/RFID

ENERGY METER

BUS OUTBUS IN

CONTROL/RFID ENERGY METERCONTROL/RFID ENERGY METER

USB-INTERFACE FOR ENERGY METERS

USB-terminals RS485 SINGLE-PHASE ENERGY METER* THREE-PHASE ENERGY METER*

Yellow BTerminal 8 Terminal 9

Black MTerminal 7 Terminal 10

Orange ATerminal 6 Terminal 8

Make sure A and B are the

same twisted pair. Use the

same colours throughout

the network to minimize the

risk for incorrect wiring.

Make sure A and B are

the same twisted pair.

Use the same colours

throughout the network

to minimize the risk for

incorrect wiring.

7 8 9 10 7 8 9 10

6 7 8 6 7 8

CONTROL/RFID ENERGY METER

BUS OUTBUS IN

CONTROL/RFID ENERGY METER

7 8 9 10 7 8 9 10

6 7 86 7 8

CONTROL/RFIDENERGY METER

BUS OUT

ENERGY METER

and/or

7 8 9 10 7 8 9 10

6 7 86 7 8

CONTROL/RFIDENERGY METER

BUS OUTBUS IN

ENERGY METER

and/or

Yellow B Terminal 8

Black M Treminal 7

Orange A Treminal 6

7 8 9 10 7 8 9 10

6 7 8 6 7 8

CONTROL/RFID ENERGY METER

BUS OUTBUS IN

CONTROL/RFID ENERGY METER

7 8 9 10 7 8 9 10

6 7 86 7 8

CONTROL/RFIDENERGY METER

BUS OUT

ENERGY METER

and/or

7 8 9 10 7 8 9 10

6 7 86 7 8

CONTROL/RFIDENERGY METER

BUS OUTBUS IN

ENERGY METER

and/or

Yellow B Terminal 8

Black M Treminal 7

Orange A Treminal 6

* The CLU only supports a specic type of three-phase and single-phase energy meters and is not

compatible with any other suppliers. Contact DEFA for specications.

*For other combinations, see CLU MK1 installation manual chapter 9.

DEFA CLU MK1 - Quick Guide IVersion 1.18 9DEFA CLU MK1 - Quick Guide IVersion 1.1

The SD card is inserted in the

slot on the top of the CLU, pins

facing outwards.

Connect the 12V LVPS to the

modem.

Connect the 230V AC to the

primary side of the 12V LVPS.

Connect the antenna to the

modem.

NOTE: Make sure to place the

antenna where there is sufcient

reception.

Connect the USB-RS232 to one of

the four USB ports on the CLU.

Connect the 5V LVPS to

the CLU.

Connect 230V AC to the

primary side of the 5V

LVPS.

Connect the USB interface

for controller/RFID bus to

one of the four USB ports

on the CLU.

When required; CLU Basic

can be connected online

through a LAN cable.

3 IInstalling the CLU

Make sure the CLU is powered off before connecting the USB interface.

The SD card is congured specically for every single CLU. Make sure the

SD card is placed in the correct unit.

INSTALLING A CLU BASIC:

HOW TO INSERT THE SD CARD:

INSTALLING A CLU COM:

Connect the 5V LVPS and the

Controller/RFID by following steps

1 to 3 on the previous page.

LVPS 5V

DC OK

LVPS 12V

DC OK

5VDC 12VDC

230VAC 230VAC

4AC AC

LVPS 5V

DC OK

5VDC

230VAC

34 AC

DEFA CLU MK1 - Quick Guide IVersion 1.110 11DEFA CLU MK1 - Quick Guide IVersion 1.1

HOW TO INSERT THE SIM CARD INTO THE MODEM:

Push the SIM card lid in the

direction of the arrow on the lid

and remove it from the modem.

Push the SIM card tray in the

opposite direction as the lid and

lift it to open position.

Insert the SIM card into the SIM

card tray as illustrated.

Close the SIM card tray and slide

it back in position. A rm click will

conrm the correct position.

1 3

CLICK!

1 2 3 4

CONNECTING ENERGY METER(S) IN THE DISTRIBUTION BOARD TO THE CLU:

The energy meter bus must be

connected together in a daisy

chain connection.

Connect the USB interface for the

energy meter(s) to one of the four

USB ports on the CLU.

The energy meter data requires

online connection, either through

LAN-cable or modem connection.

LVPS 5V

DC OK

5VDC

230VAC

Select which Device type to

congure; Controller(EVCC2),

RFID reader or Energy Meter.

Click Scan bus to locate this

device in the charge point or on

the bus.

Select the device for

conguration.

4 I Conguration

Turn off the power to all devices in the network, except the device to be

congured.

The SD card is congured specically for every single CLU. Make sure the

SD card is placed in the correct unit.

CONNECTING TO A DEVICE: 1

Install the DEFA Charge Point Congurator (CPC) on a Windows computer

or Android smartphone.

Connect the conguration kit to the bus or an individual charge point,

and a unit with the CPC software installed.

123

DEFA CLU MK1 - Quick Guide IVersion 1.112 13DEFA CLU MK1 - Quick Guide IVersion 1.1

HOW TO CONFIGURE THE CONTROLLER:

HOW TO CONFIGURE AN RFID READER TO CLU:

Set Mode to CLU.

Set the Address according to the

Charge Point Parameter Settings.

Set the Max current according

to the Charge Point Parameter

Settings.

Click Write to save settings.

Select Set to online to connect the

RFID reader to the CLU network.

Set the mode in the Controller settings

to RFID Standalone, then select this

as Device type.

HOW TO CONFIGURE AN ENERGY METER:

When the RFID reader is

congured to Online, enter the

Address specied by the Charge

Point Parameter Settings.

Click Write to save settings.

Set the address specied by the

Charge Point Parameter Settings.

Make sure that Baud rate is set

to 38400, parity is set to NONE and

stop bits are set to 1.

Click Write to save settings.

When conguring an energy meter,

connect the conguration kit to the

energy meter bus.

DEFA CLU MK1 - Quick Guide IVersion 1.114 15DEFA CLU MK1 - Quick Guide IVersion 1.1

HOW TO LABEL AN ERANGE UNO FOR

CloudCharge OR LADE I NORGE:

DEFA test box for charging station.

Art.nr.: 710253

5 ICompleting the installation

While connected through the CPC, turn on all charging stations and scan bus to

conrm that all devices have the correct address.

When energy meters are installed, connect the CPC kit to the energy meter bus to

conrm that all devices have the correct address.

Conrm that all charge points begin charging when connected to a vehicle or a

test box.

Connection to CloudCharge® can be conrmed by contacting DEFA support.

6 ILabeling

Make sure the wallbox is clean and dry before labeling.

Fasten the sticker from top to bottom, and smooth it out to avoid

bubbles.

DEFA CLU MK1 - Quick Guide IVersion 1.116

HOW TO LABEL AN ERANGE DUO FOR

CloudCharge OR LADE I NORGE:

RFID

15 mm

25 mm25 mm

106 mm

43 mm 43 mm

125 mm

SMS

navn

nummer

SMS: navn

TIL: 59441556

ELISABETH

til 59 44 15 56

SMS

LINA

til 59 44 15 56

SMS

22 kW

VELKOMMEN

For å kunne lade her

må du være registrert

hos anleggseier.

Tel:

• Hvor fort kan jeg lade her?

• Jeg får ikke ladet - hvorfor ?

www.ladeinfo.no

Beskrivelse for merking av ladeboks

Contact DEFA:

Finland:

Phone: +35 82 01 52 72 00

Norway:

Phone: +47 32 06 77 00

Mail:[email protected]

Sweden:

Phone: +46 01 04 98 38 00

Mail: emobility[email protected]

712316 - E00 - NK 20191016

www.defa.com

Andere Handbücher für CLU MK1

Inhaltsverzeichnis

Andere DEFA Akkuladegerät Handbücher

DEFA

DEFA MultiCharger 1x12 Bedienungsanleitung

DEFA

DEFA Solid Bedienungsanleitung

DEFA

DEFA WorkshopCharger DWSC125 Bedienungsanleitung

DEFA

DEFA SmartCharge 701515 Bedienungsanleitung

DEFA

DEFA WorkShopCharger 35A Bedienungsanleitung

DEFA

DEFA REDARC SmartCharge 4A Bedienungsanleitung

DEFA

DEFA MultiCharger 1x12A Bedienungsanleitung

DEFA

DEFA MultiCharger 1x7 Bedienungsanleitung

DEFA

DEFA SmartCharge 701515 Bedienungsanleitung

DEFA

DEFA MultiCharger 1203 Handbuch

DEFA

DEFA 125A Bedienungsanleitung

DEFA

DEFA WorkShopCharger 35A Bedienungsanleitung

DEFA

DEFA Solid Bedienungsanleitung

DEFA

DEFA ShowroomCharger 32A Bedienungsanleitung

DEFA

DEFA eRange ACC 710346 Bedienungsanleitung

DEFA

DEFA ShowroomCharger 50A Bedienungsanleitung

DEFA

DEFA MultiCharger 1x35A Bedienungsanleitung

DEFA

DEFA MultiCharger 40A 24V Bedienungsanleitung

DEFA

DEFA PowerSystems 1x15 Bedienungsanleitung

DEFA

DEFA REDARC SBC1230-S Bedienungsanleitung

DEFA

DEFA MultiCharger 1205R Flex Bedienungsanleitung

DEFA

DEFA WorkShopCharger 25A Bedienungsanleitung

DEFA

DEFA MultiCharger 1x20A Bedienungsanleitung

DEFA

DEFA WorkShopCharger 35A Bedienungsanleitung

Beliebte Akkuladegerät Handbücher anderer Marken

AA Portable Power Corp

AA Portable Power Corp Universal Smart Charger Bedienungsanleitung

Enelion

Enelion Vertica Bedienungsanleitung

RCA

RCA CHU6 Bedienungsanleitung

ANSMANN

ANSMANN ALCT 6/24-10 Bedienungsanleitung

Hitachi

Hitachi UC 18YRSL Fehlerbehebungshandbuch

Olympus

Olympus B-20 LPC Bedienungsanleitung

Exibel

Exibel ZH1708143 Bedienungsanleitung

Lenmar

Lenmar Mach 1 Bedienungsanleitung

CTEK

CTEK MXS 5.0 Bedienungsanleitung

ABB

ABB HT842379 Bedienungsanleitung

Nitecore

Nitecore Superb Charger SC4 Bedienungsanleitung

Renogy

Renogy RBC2125DS-21W Bedienungsanleitung

Braun

Braun BWC02M Bedienungsanleitung

CTEK

CTEK MXS 3.6 Bedienungsanleitung

Black & Decker

Black & Decker BDV090 Bedienungsanleitung

Trinity

Trinity DPD Bedienungsanleitung

Hulkman

Hulkman Sigma 1 Bedienungsanleitung

IKEA

IKEA koppla Bedienungsanleitung