Defiant 5985 Bedienungsanleitung

THANK YOU

We appreciate the trust and condence you have placed in Deant through the purchase of this motion security light.

We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of

products available for your home improvement needs. Thank you for choosing Deant!

USE AND CARE GUIDE

MOTION SECURITY LIGHT

Questions, problems, missing parts?

Before returning to the store, call Deant Customer Service

8 a.m.-7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday

1-866-308-3976

HOMEDEPOT.COM

Item #1001318516

1001311061

Model #DFI-5985-BZ

DFI-5985-WH

Model # 5985

Serial # DFI-5985-BZ, DFI-5985-WH

Table of Contents

Table of Contents......................................2

Safety Information....................................2

Warranty ...................................................2

5-Year Limited Warranty ........................2

Pre-Installation.........................................3

Planning Installation ..............................3

Specications ........................................3

Tools Required .......................................3

Hardware Included.................................4

Package Contents..................................4

Installation................................................5

Operation...................................................7

Care and Cleaning ..................................11

Troubleshooting......................................11

Safety Information

PRECAUTIONS

ƑPlease read and understand this entire manual

before attempting to assemble, install, or operate

this light xture.

ƑThis light xture requires a 120-Volt AC power

source.

ƑSome codes require installation by a qualied

electrician.

ƑThis light xture must be properly grounded.

ƑThis light xture should be installed outdoors to a

wall or eave.

ƑThe light xture should be mounted approximately

8 ft. (2.4 m) above the ground. If the light xture

is mounted higher than recommended, aiming the

sensor down will reduce the coverage area.

WARNING: Turn the power off at the circuit breaker or

fuse. Place tape over the circuit breaker switch and verify

power is off at the light xture.

WARNING: Risk of re. Keep the lamp heads at least

2in. (51mm) from combustible materials.

CAUTION: Burn hazard. Allow the light xture to cool

before touching.

ƑThis device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference,

and (2) this device must accept any interference

received, including interference that may cause

undesired operation.

ƑCAN ICES-3 (B)/NMB-3(B)

Warranty

5-YEAR LIMITED WARRANTY

WHAT IS COVERED

This product is guaranteed to be free of factory defective parts and workmanship for a period of 5 years from date

of purchase. Purchase receipt is required for all warranty claims.

WHAT IS NOT COVERED

This guarantee does not include repair service, adjustment and calibration due to misuse, abuse or negligence, or

LEDs. Unauthorized service or modication of the product or of any furnished component will void this warranty in

its entirety. This warranty does not include reimbursement for inconvenience, installation, setup time, loss of use,

unauthorized service, or return shipping charges. This warranty is not extended to other equipment and components

that a customer uses in conjunction with this product.

Contact the Customer Service Team at 1-866-308-3976 or visit www.homedepot.com.

3 HOMEDEPOT.COM

Please contact 1-866-308-3976 for further assistance.

Pre-Installation

PLANNING INSTALLATION

Before installing the light xture, ensure that all parts are present. Compare parts with the Hardware Included and

Package Contents sections. If any part is missing or damaged, do not attempt to assemble, install, or operate this

light xture.

Estimated installation time: 30 minutes

SPECIFICATIONS

Range Up to 70 ft. (21.3 m) (Varies with surrounding temperature)

Sensing angle Up to 270°

Electrical load - LED 28 Watts

Lumens 2350

Power requirements 120 VAC, 60 Hz

Operating modes Test, Motion activated, Manual

Time delay 1, 5, 20 minutes

DualBrite timer Off, 3 hours, 6 hours, dusk-to-dawn

Mobile device requirements iPhone 4S or newer running iOS 7.x or later.

Android v4.3 or later.

Phone must also have Bluetooth®version 4.0 or later.

TOOLS REQUIRED

Phillips

screwdriver

1/8 in. Flathead

screwdriver

Wire strippers/

cutters

Circuit tester Work gloves Silicone

sealant

Ladder Safety goggles Mobile Device

Pre-Installation (continued)

HARDWARE INCLUDED

NOTE: Hardware shown to actual size.

AA BB CC DD

FRONT

Part Description Quantity

AA Rubber plug 1

BB Mounting bracket screw 2

CC Mounting bracket screw 2

DD Mounting bracket screw 2

EE Large mounting bolt (pre-installed) 1

FF Small mounting bolt 1

GG Mounting bracket (not to scale) 1

HH Mini screwdriver 1

PACKAGE CONTENTS

Part Description Quantity

A Lamp head 2

B Light xture 1

C Motion sensor 1

D1-2- asy Connect™ 1

5 HOMEDEPOT.COM

Please contact 1-866-308-3976 for further assistance.

Installation

1 Determining the mounting

location

NOTE: The light xture should be mounted approximately

8 ft. (2.4 m) above the ground. If the light xture is

mounted higher than recommended, aiming the sensor

down will reduce the coverage area.

ƑDetermine the mounting location – wall or eave

mount.

ƑPosition the lamp heads (A) in the general

direction of the desired light coverage.

ƑIf needed, rotate the motion sensor (C) so the

text faces upward.

Wall Mount

Eave Mount

2 Removing the 1-2- asy

Connect™

NOTE: This xture comes with a 1-2- asy Connect™ (D).

It is pre-assembled on the light xture (B) for shipping.

NOTE: The large mounting bolt (EE) is pre-installed in

the light xture (B). Do not attempt to remove the large

mounting bolt (EE).

ƑUnscrew the large mounting bolt (EE) connecting

the light xture (B) to the 1-2- asy Connect™ (D)

and remove the 1-2- asy Connect™ (D).

3 Installing the mounting bracket

WARNING: Turn the power off at the circuit breaker or

fuse. Place tape over the circuit breaker switch and verify

power is off at the light xture.

NOTE: Six mounting bracket screws of various sizes are

included. The installation will only require two. Discard the

unused mounting bracket screws after installation.

ƑRemove the existing light xture.

ƑInstall the mounting bracket (GG) with the

stamped word “FRONT” facing away from the

junction box. Use the mounting bracket screws

(BB, CC, or DD) that best t the junction box.

ƑFirmly pull on the mounting bracket to verify

it is securely mounted to the junction box. If

necessary, use the screws that were removed

from the existing light xture.

FRONT

BB, CC, or DD

Installation (continued)

4 Installing the 1-2- asy

Connect™

ƑRoute the junction box wires through the large

hole in the 1-2- asy Connect™ (D).

ƑPlace the 1-2- asy Connect™ (D) against the

junction box.

ƑWhen mounting to a wall, the “UP” arrow

must point upward.

ƑWhen mounting to an eave, the “UP” arrow

must point toward the building.

ƑInsert the small mounting bolt (FF) through the

1-2- asy Connect™ (D) hole located below

the threaded hole, and thread it into the center

hole of the mounting bracket (GG). Tighten the

bolt (FF) securely.

ƑFirmly pull on the 1-2- asy Connect™ to verify

it is securely attached to the mounting bracket.

FRONT

N (White/

Blanc/Blanco)

GND

Terre

Tierra

UP/Haut/Arriba

L(Black/

Noir/Negro)

UP/Haut/Arriba

5 Making the electrical

connections

ƑInsert the junction box wires into the side of

the terminal block and around the ground

screw. Tighten terminal block screws using

the mini-screwdriver (HH) and ground screw to

secure the wires.

ƑInsert the white wire from the junction box

into the terminal marked “N (White)”.

ƑInsert the black wire from the junction box

into the terminal marked “L (Black)”.

ƑConnect the bare or green ground wire

from the junction box to the ground screw

(marked with “GND”).

N (White/

Blanc/Blanco)

GND

Terre

Tierra

UP/Haut/Arriba

L (Black/

Noir/Negro)

6 Mounting the light fixture

NOTICE: The two pins on the rear of the light xture must be

inserted into the terminal block for the light to work.

ƑAlign the bottom edge of the light xture (B) with

the bottom edge of the 1-2- asy Connect™ (D)

and tilt the light xture (B) toward the

1-2- asy Connect™ (D). Ensure the light xture

(B) is centered on the 1-2- asy Connect™ (D).

ƑTighten the large mounting bolt (EE) securely

through the center of the 1-2- asy Connect™

(D). Do not overtighten.

ƑPush the rubber plug (AA) rmly into the

mounting bolt hole on the light xture (B).

7 HOMEDEPOT.COM

Please contact 1-866-308-3976 for further assistance.

Installation (continued)

7 Caulking around the light

fixture

ƑCaulk around the 1-2- asy Connect™ (D) and

mounting surface with silicone sealant (not

included).

Operation

1 Adjusting the lamp heads

WARNING: Risk of re. Keep the lamp heads at least

2in. (51mm) from combustible materials.

CAUTION: Keep lamp heads 30° below horizontal to

avoid water damage and electrical shock.

ƑTurn the power on at the circuit breaker or fuse

and turn on the wall switch.

ƑIf needed, gently grasp the lamp heads (A) and

tilt them up or down or side to side to adjust

the light coverage area.

2 Rotating the sensor controls

downward

ƑRotate the motion sensor (C) so the text faces

upward.

NOTICE: All clearances must be maintained. See Safety Information

on page 2.

NOTICE: The Deant mobile app must be downloaded to operate

the light xture. See Step 3 on page 8 for instructions.

270°

THIS SIDE UP

Operation (continued)

3 Downloading the Defiant®

mobile app

ƑDownload the Deant®mobile app from the

Apple®or Android®app store (search for

“Deant”).

ƑTurn on the Bluetooth®in the device

settings.

ƑOpen the Deant app and touch “Begin”.

Conﬁguring your light settings with a mobile

device requires Bluetooth connectivity.

Before proceeding, ensure your mobile device’s

Bluetooth is turned on. The Bluetooth indicator

icon should appear somewhere on the screen.

If it does not, go into your mobile device’s Settings

menu and turn it on.

TURN ON BLUETOOTH

Begin

7:15 AM

68%

Configuring your light settings with

a mobile device requires Bluetooth

connectivity.

Before proceeding, ensure your

mobile device’s Bluetooth is turned

on. The Bluetooth indicator icon

should appear somewhere on the

screen. If it does not, go into your

mobile device’s Settings menu and

turn it on.

TURN ON BLUETOOTH

Begin

ATT 100 %9:25 PM

Android iOS

4 Pairing the light to the mobile

app

ƑEnsure the power to the light is turned ON.

ƑTouch “Scan for lights” to search for existing

lights.

NOTE: During the scanning process, the app will locate

ALL Bluetooth®lights in the area. Lights previously

paired to other devices should already be named.

Scan for lights

SELECT A LIGHT

No lights conﬁgured

7:15 AM

68%

My Lights All My Lights All

Scan for lights

SELECT A LIGHT

No lights configured

ATT 100 %9:25 PM

Android iOS

5 Beginning the pairing process

The new light will be shown in a yellow circle

indicating it is not paired.

ƑTouch the new light to begin the pairing

process.

SELECT A LIGHT

New Light

7:15 AM

68%

My Lights All My Lights All

SELECT A LIGHT

ATT 100 %9:25 PM

New Light

Android iOS

6 Finishing the pairing process

ƑTouch “Set Up” and enter a name and

password for the light (the password must be

4 to 6 alpha-numeric characters).

ƑEither touch “Save” to continue or “Add Photo”

to add an optional picture (the photo may be

an existing photo or a new photo may be taken

of the light).

NOTE: A preview of the light will not show until the

“Save” button is touched.

Set Up

7:15 AM

68%

Cancel Save

Add Photo

Please create a password

Password

Enter name

Name This Light

Verify password

Verify Password

Add Image

ATT 100 %9:25 PM

Set UpBack

Name This Light

Password

Verify Password

Add Image

Add Photo

Cancel Save

Please create 4 character password

Android iOS

9 HOMEDEPOT.COM

Please contact 1-866-308-3976 for further assistance.

Operation (continued)

7 Adjusting the light settings

After the light is paired to the mobile app, the yellow

circle around the light will change to green.

ƑTouch the light icon.

ƑTouch “Settings” to adjust the light controls.

ƑTouch “Save” after all adjustments have been

made. Setup is complete.

NOTE: Changes made to one light’s settings will not

affect another light’s settings.

Settings

7:15 AM

68%

Cancel Save

ON time

5 minutes

Sensitivity

Medium

DualBrite time

3 hours

Full ON brightness level

DualBrite dimming level

75%

25%

ATT 100 %

9:25 PM

SettingsPorch

ON Time: 5 Minutes

Full ON Brightness Level: 85%

Sensitivity: Medium

DualBrite Dimming Level: 25%

Cancel Save

20 Minutes1 Minute 5 Minutes

HighLow Medium

DualBrite Time: 3 Hours

Dusk to Dawn6 HoursOff 3 Hours

Android iOS

The “ON-TIME” option determines the amount of time

the light will stay on “Full ON Brightness Level” after

all motion has stopped.

The “Full ON Brightness Level” option determines the

light brightness level after the light has been turned

on by motion.

The “Sensitivity” option increases and decreases the

size of the detection area.

The “DualBrite” option determines the amount of

time the lights stay on at a reduced light level after

sundown. Switching this setting to “OFF” will not

affect the “ON-TIME” setting.

The “DualBrite Dimming Level” option determines the

light brightness level of the reduced light level after

sundown.

NOTE: The higher the “Sensitivity” setting, the greater the

possibility of false triggering. To reduce false triggering,

select a lower setting.

NOTE: The “Dusk-to-Dawn” setting keeps the lights on at

an accent level from sundown to sun up.

NOTE: If the “DualBrite” option is set to OFF, changing the

dimming level will have no affect on the light.

8 Setting the sensor for testing

NOTE: The light xture will operate during the day or

night during testing. The light will stay on for 8 seconds

after all motion is stopped.

The light xture will automatically enter “Test” mode

whenever the “Sensitivity” option is changed. The light

xture will remain in “Test” until one of the following

actions occurs:

ƑThe “Save” or “Cancel” option is selected.

ƑNo movement during the testing process for 30

seconds.

ƑThree minutes have passed without changing

one of the on-screen settings.

ƑSet the “DualBrite” option to the “OFF”

position.

ƑSet the “Sensitivity” option to the “LOW”

position.

NOTE: The motion sensor will need to completely warm

up (60 seconds) before beginning the setup process.

Operation (continued)

9 Adjusting the motion sensor

detection zone

ƑPerform a “walk test”: walk in an arc across

the front of the motion sensor (C).

ƑWatch the light. The light will come on and the

red LED will ash indicating motion has been

detected.

ƑStop, wait for the light to turn off, and then

begin walking again.

ƑContinue this process until the detection zone

has been established.

ƑIf needed, gently grasp the motion sensor (C)

and move it from side to side or up and down

to adjust the detection zone.

NOTE: The motion sensor (C) is more sensitive to motion

moving across the front of the sensor. The motion sensor

front of the sensor.

10 Adding additional mobile

devices

Additional mobile devices may be added to control the

light xture.

ƑOn the new device follow steps 3 and 4 above.

ƑAfter scanning for lights, select the “All” tab.

ƑTouch the desired light on the screen and enter

the previous user-dened password.

NOTE: The light settings and name are stored in the light

xture. The light photo will need to be added separately.

This light is conﬁgured on another

smartphone

Enter the light’s password to gain normal

access:

Password

7:15 AM

68%

Deck

ATT 100 %9:25 PM

DeckBack

Password

This light is configured on

another smartphone

Enter the light’s password to gain

normal access:

Android iOS

Using manual mode

Manual mode overrides the motion sensor (C) and

“ON-TIME” control so the light will operate at the preset

“Full ON Brightness Level”

. This feature only works at

night and only for one night at a time. The motion sensor

ƑSlide the switch under “Manual Override” to

the right.

ƑTo return the light to the original settings, slide

the switch to the left.

NOTE: If the power to the light xture is off for more than

5 seconds, allow the motion sensor to warm up prior to

switching to manual mode.

My Lights All

SELECT A LIGHT

Side Door

Garage Front

Porch

Deck

OFF

Manual

Override

7:15 AM

68%

ATT 100 %9:25 PM

SELECT A LIGHT

Side Door

Garage Front

Porch

Deck

My Lights All

Manual

Override

Android iOS

Inhaltsverzeichnis

Sprachen:

Andere Defiant Scheinwerfer Handbücher

Defiant

Defiant DFI-7167-WH-G Bedienungsanleitung

Defiant

Defiant DFI-5982-BZ Bedienungsanleitung

Defiant

Defiant 1002366429 Bedienungsanleitung

Defiant

Defiant DFI-7005-WH-G Bedienungsanleitung

Defiant

Defiant DFI-7148-BK Bedienungsanleitung

Defiant

Defiant DFI-8852-BZ-G Bedienungsanleitung

Defiant

Defiant DFI-5983-BZ Bedienungsanleitung

Defiant

Defiant CD-5936-BK Bedienungsanleitung

Defiant

Defiant DFI-5851-BK Bedienungsanleitung

Defiant

Defiant DFI-7004-WH-G Bedienungsanleitung

Defiant

Defiant DFI-0654-WH Bedienungsanleitung

Defiant

Defiant DF-5928-BZ-A Bedienungsanleitung

Defiant

Defiant DFI-5408-GR Bedienungsanleitung

Defiant

Defiant DFI-0452-WH Bedienungsanleitung

Defiant

Defiant CD-5928-WH-A Bedienungsanleitung

Defiant

Defiant MSH27920DLWD Bedienungsanleitung

Defiant

Defiant H32-0C000XD19 Bedienungsanleitung

Defiant

Defiant FSL2030LDF Bedienungsanleitung

Defiant

Defiant DFI-5892-WH Bedienungsanleitung

Defiant

Defiant MST18920lwdf Bedienungsanleitung

Defiant

Defiant MSLED1801D Bedienungsanleitung

Defiant

Defiant DF-5909-WH Bedienungsanleitung

Defiant

Defiant DF-5416-BK-B Bedienungsanleitung

Defiant

Defiant CD-5928-WH Bedienungsanleitung

Beliebte Scheinwerfer Handbücher anderer Marken

VIZULO

VIZULO Micro Martin Benutzerhandbuch

EuroLite

EuroLite LED IP FL-100 SMD Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock XB12 Bedienungsanleitung

Allen + Roth

Allen + Roth 17624-000 Bedienungsanleitung

ADJ

ADJ 4 STAGE PAK Bedienungsanleitung

Cooper Lighting

Cooper Lighting EGL91SW233 Bedienungsanleitung

Max

Max 37496 Bedienungsanleitung

BEGA

BEGA 85 143 Bedienungsanleitung

Beamz

Beamz 151.226 Bedienungsanleitung

EuroLite

EuroLite LED IP FL-8 Bedienungsanleitung

Ledj

Ledj PERFORMER 36 RGB Bedienungsanleitung

Perel

Perel ELS3 Bedienungsanleitung

Perel

Perel ELS3WD Bedienungsanleitung

LumX

LumX LM 36130 Bedienungsanleitung

Xtricity

Xtricity 4-80053 Bedienungsanleitung

Stahl

Stahl 6521/4 Series Bedienungsanleitung

Ecosense

Ecosense EcoSpec Bedienungsanleitung

Ayrton

Ayrton minipanel FX Bedienungsanleitung