Defiant DF-5909-WH Bedienungsanleitung

THANK YOU

We appreciate the trust and condence you have placed in Deant through the purchase of this motion security light.

We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of

products available for your home improvement needs. Thank you for choosing Deant!

USE AND CARE GUIDE

MOTION SECURITY LIGHT

Questions, problems, missing parts?

Before returning to the store, call Deant Customer Service

8 a.m.-7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday

1-866-308-3976

HOMEDEPOT.COM

Item #1004365415

Model #DF-5909-WH

Table of Contents

Table of Contents......................................2

Safety Information....................................2

Warranty ...................................................2

5-Year Limited Warranty ........................2

Pre-Installation.........................................3

Planning Installation ..............................3

Specications ........................................3

Tools Required .......................................3

Hardware Included.................................4

Package Contents..................................4

Installation................................................5

Operation...................................................8

Care and Cleaning ..................................11

Troubleshooting ......................................11

Safety Information

PRECAUTIONS

□Please read and understand this entire manual

before attempting to assemble, install, or operate

this light xture.

□This light xture requires a 120-Volt AC power

source.

□Some codes require installation by a qualied

electrician.

□This light xture must be properly grounded.

□This light xture should be installed outdoors to a

wall or eave.

□The light xture should be mounted approximately

8 ft. (2.4 m) above the ground. If the light xture

is mounted higher than recommended, aiming the

sensor down will reduce the coverage area.

WARNING: Turn the power off at the circuit breaker or

fuse. Place tape over the circuit breaker switch and verify

power is off at the light xture.

CAUTION: To avoid water damage and the risk of

electrical shock, the motion sensor controls must be facing

the ground when the installation is complete.

CAUTION: Burn hazard. Allow the light xture to cool

before touching.

NOTICE: Do not connect this light xture to a dimmer switch or

timer.

Warranty

5-YEAR LIMITED WARRANTY

WHAT IS COVERED

This product is guaranteed to be free of factory defective parts and workmanship for a period of 5 years from date

of purchase. Purchase receipt is required for all warranty claims.

WHAT IS NOT COVERED

This guarantee does not include repair service, adjustment and calibration due to misuse, abuse or negligence, or

LEDs. Any damage to the light xture resulting from the use of chemicals or a pressure washer machine are not

covered by this warranty. Unauthorized service or modication of the product or of any furnished component will

void this warranty in its entirety. This warranty does not include reimbursement for inconvenience, installation,

setup time, loss of use, unauthorized service, or return shipping charges. This warranty is not extended to other

equipment and components that a customer uses in conjunction with this product.

No service parts available for this product.

Contact the Customer Service Team at 1-866-308-3976 or visit www.homedepot.com.

3 HOMEDEPOT.COM

Please contact 1-866-308-3976 for further assistance.

Pre-Installation

PLANNING INSTALLATION

Before installing the light xture, ensure that all parts are present. Compare parts with the Hardware Included and

Package Contents sections. If any part is missing or damaged, do not attempt to assemble, install, or operate this

light xture.

Estimated installation time: 30 minutes

SPECIFICATIONS

Range Up to 50 ft. (15.2 m) (Varies with surrounding temperature)

Sensing angle Up to 270°

Electrical load - LED 33 Watts

LED lumens 2000

LED color temperature 3000K (warm white)

Power requirements 120 VAC, 60 Hz

Operating modes Test (day and night), Motion activated (night only), Manual (night only)

Time delay (motion) 5 or 20 minutes (night only)

DualBrite timer (night only) Off, 5 hours, dusk-to-dawn

TOOLS REQUIRED

Phillips

screwdriver

1/8 in. Flathead

screwdriver

Wire strippers/

cutters

Circuit tester Work gloves Silicone

sealant

Ladder Safety goggles

Pre-Installation (continued)

HARDWARE INCLUDED

NOTE: Hardware shown to actual size.

AA BB CC

Part Description Quantity

AA Clear rubber gasket (pre-installed) 2

BB #8 Mounting plate screw (pre-installed) 2

CC #10 Mounting plate screw 2

PACKAGE CONTENTS

Part Description Quantity

A Light panel 2

B Canopy 1

C Motion sensor 1

D Mounting plate 1

E Heat sink 2

5 HOMEDEPOT.COM

Please contact 1-866-308-3976 for further assistance.

Installation

1 Determining the mounting

location

NOTE: The light xture should be mounted approximately

8 ft. (2.4 m) above the ground. If the light xture is

mounted higher than recommended, aiming the sensor

down will reduce the coverage area.

□Determine the mounting location – wall or eave

mount.

□Position the light panels (A) in the general

direction of the desired light coverage.

□If needed, rotate the motion sensor (C) so the

controls face the ground after installation.

Wall Mount

Eave Mount

Wiring the mounting plate

IMPORTANT: Push-in terminals not for reuse.

To remove the wires from the mounting plate connector, twist the wires

back and forth as the wires are being pulled from the mounting plate.

If the house wiring is solid copper wire, proceed with

step 2. If the house wiring is stranded copper wire,

proceed to step 3.

2 Connecting solid copper house

wire

WARNING: Turn the power off at the circuit breaker or

fuse. Place tape over the circuit breaker switch and verify

power is off at the light xture.

IMPORTANT: This mounting plate is designed for solid-core 14

or 12 AWG wire. If the house wiring is stranded wire, see step 3,

Connecting stranded house wire below.

NOTE: If necessary, strip 5/8 in. of insulation from

junction box wires. Use the wire length measuring guide

on the back of the mounting plate to ensure the correct

wire length.

□Remove the existing light xture.

□Insert the junction box wires (1) into the side of

the terminal block on the back of the mounting

plate (D).

□Insert the white wire from the junction box

into the terminal marked “N”.

□Insert the black wire from the junction box

into the terminal marked “L”.

□Insert the bare or green ground wire from

the junction box into the terminal marked

“G”.

□Proceed to step 4, page 7.

5/8"

Installation (continued)

3 Connecting stranded copper

house wire

WARNING: Turn the power off at the circuit breaker or

fuse. Place tape over the circuit breaker switch and verify

power is off at the light xture.

IMPORTANT: Use only NM-B 14/2 or 12/2 wire for the pigtail. The

pigtail wire size must match the existing house wiring (14 AWG or

12 AWG). Color match the solid-core wire and the house wire when

connecting together.

If the house wiring is stranded wire instead of solid-

core copper wire, a pigtail using solid-core wire (2) will

be required (not included). Follow these instructions

to connect the mounting plate (D) using the pigtail

method.

□Cut 4 to 6 inches of NM-B wire (2) to match the

existing house wire (14 AWG or 12 AWG).

□If necessary, strip 5/8 in. of insulation from

junction box wires (1).

□Strip 5/8 in. of insulation from one end of the

solid-core wire (2).

□Attach the two wires together using a wire

nut(3 - not included). Ensure the solid-core

wire insulation matches the junction box wire.

□Repeat for the remaining two wires.

□To attach the solid-core pigtail to the mounting

plate (D), strip 5/8 in. of insulation from the

other end of the solid-core wire. Use the wire

length measuring guide on the back of the

mounting plate (D) to ensure the correct wire

length.

□Insert the pigtail wires into the side of the

terminal block on the back of the mounting

plate (D).

□Insert the white pigtail wire into the

terminal marked “N”.

□Insert the black pigtail wire into the

terminal marked “L”.

□Insert the bare or green ground pigtail

wire into the terminal marked “G”.

5/8"

7 HOMEDEPOT.COM

Please contact 1-866-308-3976 for further assistance.

Installation (continued)

4 Installing the mounting plate

□Place the mounting plate (D) against the

junction box.

□Tighten the two mounting screws (BB) securely

to the junction box. If necessary, use the

screws that were removed from the existing

light xture. Do not overtighten.

□Firmly pull on the mounting plate(D) to ensure

it is securely attached to the junction box.

IMPORTANT: Use the larger mounting plate screws if the pre-

installed screws are too small for the junction box holes.

• Unscrew the mounting plate screws from the mounting plate

using a screwdriver.

• Remove the rubber gaskets from the mounting plate screws.

• Place the rubber gaskets on the larger mounting plate screws and

screw the screws into the mounting plate using a screwdriver.

5 Mounting the light fixture

NOTICE: The light xture must securely snap onto the mounting

plate completely for the locking handle to close.

During the installation, DO NOT press against the

light panels (A) or the heat sinks (E). Move the light

panels(A) apart and apply pressure directly to the light

xture housing.

□Pull up on the locking handle (4) to unlock.

□Align the back of the light xture with the

mounting plate (D).

□Firmly press the center of the light xture

housing to securely snap the light xture onto

the mounting plate (D). The light xture must be

fully seated onto the mounting plate (D) all the

way around.

6 Locking the light fixture

□Rotate the light xture to the desired position.

□Press down on the locking handle (4)

completely to secure the light xture to the

mounting plate (D).

NOTICE: Gently pull on the light xture to ensure it is securely

connected to the mounting plate.

Installation (continued)

7 Caulking around the light

fixture

CAUTION: Failure to completely caulk around the light

xture’s mounting plate could result in water seepage into

the junction box.

□Caulk around the mounting plate (D) and

mounting surface with silicone sealant (not

included).

Operation

1 Adjusting the light panels

CAUTION: Heat sinks can be warm to the touch. Turn

light xture off for 5 minutes before touching heat sinks.

□Turn the power on at the circuit breaker or

fuse and turn on the wall switch. The motion

sensor (C) will need to completely warm up (60

seconds) before beginning the setup process.

□If needed, gently grasp the top and bottom of

the light panels (A) and tilt them up or down or

side to side to adjust the light coverage area.

2 Rotating the sensor controls

downward

This motion sensor (C) has a built-in detection system

to help ensure the sensor (C) is adjusted correctly. If

the motion sensor (C) is angled incorrectly, all of the

control lights on the bottom of the sensor (C) will come

on and the light panels (A) will turn off. The light will

stay off until the motion sensor (C) has been adjusted

correctly.

□Rotate the motion sensor (C) so the controls

face toward the ground.

NOTE: If the motion sensor is NOT positioned correctly, all

of the control lights will be glowing (shown).

DUALBRITE

D2D

OFF

HIGH

MED

LOW

20MIN

5MIN

TEST

SENS ONTIME

DUALBRITE

D2D

OFF

HIGH

MED

LOW

20 MIN

5 MIN

TEST

SENS ON TIME

9 HOMEDEPOT.COM

Please contact 1-866-308-3976 for further assistance.

Operation (continued)

3 Setting the sensor for testing

NOTE: When the “ON-TIME” is set to the “TEST” position,

the light xture will operate during the day or night. The

light will stay on for 5 seconds after all motion is stopped.

Press the button next to each setting until the light

next to the desired setting begins to ash. Stop

pressing the button and the light will stop ashing

momentarily.

□Press the “ON-TIME” button until the “TEST”

light ashes.

□Press the “SENS” button until the “Low” light

ashes.

□Ensure the “DUALBRITE” feature is set to the

“OFF” position.

□The above settings will be used for step 4

(Adjusting the Motion Sensor Detection Zone).

DUALBRITE

D2D

OFF

HIGH

MED

LOW

20 MIN

5 MIN

TEST

SENS ON TIME

DUALBRITE

D2D

OFF

HIGH

MED

LOW

20 MIN

5 MIN

TEST

SENS ON TIME

4 Adjusting the motion sensor

detection zone

□Perform a “walk test”: walk in an arc across

the front of the motion sensor (C).

□Watch the light. The light will come on when

motion has been detected.

□Stop, wait for the light to turn off, and then

begin walking again.

□Continue this process to determine if the

motion sensor (C) is aimed toward the desired

area.

□If needed, gently grasp the motion sensor (C)

and move it from side to side or up and down

to adjust the detection zone.

5 Adjusting the ON-TIME

NOTE: When the “ON-TIME” button is set to the 5 or 20

minute position, the light will only come on during the

night. The “ON-TIME” button determines the amount of

time the light will stay on full bright after all motion has

stopped.

□Press the “ON-TIME” button until the desired

time light ashes (5 or 20 minutes).

DUALBRITE

D2D

OFF

HIGH

MED

LOW

20 MIN

5 MIN

TEST

SENS

ON TIME

DUALBRITE

D2D

OFF

HIGH

MED

LOW

20 MIN

5 MIN

TEST

SENS

ON TIME

DUALBRITE

D2D

OFF

HIGH

MED

LOW

20 MIN

5 MIN

TEST

SENS

ON TIME

TEST 5 Minutes 20 Minutes

Operation (continued)

6 Adjusting the SENS

□Press the “SENS” button until the desired

sensitivity light ashes (“Low”, “Med”, “High”).

NOTE: The motion sensor is more sensitive to motion

moving across the front of the sensor. The motion sensor is

less sensitive to motion moving directly toward the sensor.

NOTE: The higher the “SENS” setting (sensitivity), the

greater the possibility of false triggering. To reduce false

triggering, press the “SENS” button until the “Low” light

ashes.

DUALBRITE

D2D

OFF

HIGH

MED

LOW

20 MIN

5 MIN

TEST

SENS

ON TIME

DUALBRITE

D2D

OFF

HIGH

MED

LOW

20 MIN

5 MIN

TEST

SENS

ON TIME

DUALBRITE

D2D

OFF

HIGH

MED

LOW

20 MIN

5 MIN

TEST

SENS

ON TIME

LOW MEDIUM HIGH

7 Adjusting the DUALBRITE

setting

NOTE: Switching this setting to “OFF” will not affect the

motion detection (ON-TIME) setting or the daylight sensor

(photocell).

The “DUALBRITE” button determines the amount

of time the lights stay on at an accent level after

sundown when no motion has been detected. When

motion is detected, the lights will turn on full bright

for the duration of the selected “ON-TIME” setting. The

light will return to the accent level for the duration of

the selected “DUALBRITE” time.

□Press the “DUALBRITE” button until the desired

light ashes (OFF, 5 hours, or D2D (dusk-to-

dawn; sunset to sunrise).

DUALBRITE

D2D

OFF

HIGH

MED

LOW

20 MIN

5 MIN

TEST

SENS ON TIME

DUALBRITE

D2D

OFF

HIGH

MED

LOW

20 MIN

5 MIN

TEST

SENS ON TIME

DUALBRITE

D2D

OFF

HIGH

MED

LOW

20 MIN

5 MIN

TEST

SENS ON TIME

OFF 5 HOURS D2D

(Dusk-to-Dawn)

8 Using manual mode

NOTE: In order to use manual mode, the light xture must

be wired through a wall switch.

NOTE: Manual mode overrides the motion sensor so the

light will shine full bright without motion being detected.

This feature only works at night and only for one night at a

time. The motion sensorwill reset to motion sensing mode

after 6 hours or sunrise, whichever comes rst. Manual

mode is toggled on and off using a wall switch.

□Ensure the power to the light is ON and the

sensor has warmed up (60 seconds).

□To turn manual mode on, switch the power

OFF–ON–OFF–ON at the wall switch within 3

seconds.

□To turn manual mode off, switch the power

OFF–ON–OFF–ON at the wall switch within 3

seconds.

NOTE: If the power to the light xture is off for more than

5 seconds, allow the motion sensor to warm up prior to

switching to manual mode.

OFF OFFON ON

Less than 3 seconds

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Defiant Scheinwerfer Handbücher

Defiant

Defiant DF-5416-BK-B Bedienungsanleitung

Defiant

Defiant DFI-5408-GR Bedienungsanleitung

Defiant

Defiant DFI-7005-WH-G Bedienungsanleitung

Defiant

Defiant CD-5936-BK Bedienungsanleitung

Defiant

Defiant H32-0C000XD19 Bedienungsanleitung

Defiant

Defiant DFI-7004-WH-G Bedienungsanleitung

Defiant

Defiant DFI-8852-BZ-G Bedienungsanleitung

Defiant

Defiant 5985 Bedienungsanleitung

Defiant

Defiant CD-5928-WH Bedienungsanleitung

Defiant

Defiant DF-5939-BK Bedienungsanleitung

Defiant

Defiant DFI-5982-BZ Bedienungsanleitung

Defiant

Defiant DFI-0452-WH Installations- und Betriebsanleitung

Defiant

Defiant DFI-7004-WH-G Bedienungsanleitung

Defiant

Defiant DFI-0452-WH Bedienungsanleitung

Defiant

Defiant DFI-5892-WH Bedienungsanleitung

Defiant

Defiant 1002366429 Bedienungsanleitung

Defiant

Defiant DF-5928-BZ-A Bedienungsanleitung

Defiant

Defiant FSL2030LDF Bedienungsanleitung

Defiant

Defiant MSH27920DLWD Bedienungsanleitung

Defiant

Defiant DFI-5998-BK Bedienungsanleitung

Defiant

Defiant MST18920lwdf Bedienungsanleitung

Defiant

Defiant DFI-5983-BZ Bedienungsanleitung

Defiant

Defiant DFI-0452-WH Bedienungsanleitung

Defiant

Defiant DFI-7148-BK Bedienungsanleitung

Beliebte Scheinwerfer Handbücher anderer Marken

VIZULO

VIZULO Micro Martin Benutzerhandbuch

EuroLite

EuroLite LED IP FL-100 SMD Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock XB12 Bedienungsanleitung

Allen + Roth

Allen + Roth 17624-000 Bedienungsanleitung

ADJ

ADJ 4 STAGE PAK Bedienungsanleitung

Cooper Lighting

Cooper Lighting EGL91SW233 Bedienungsanleitung

Max

Max 37496 Bedienungsanleitung

BEGA

BEGA 85 143 Bedienungsanleitung

Beamz

Beamz 151.226 Bedienungsanleitung

EuroLite

EuroLite LED IP FL-8 Bedienungsanleitung

Ledj

Ledj PERFORMER 36 RGB Bedienungsanleitung

Perel

Perel ELS3 Bedienungsanleitung

Perel

Perel ELS3WD Bedienungsanleitung

LumX

LumX LM 36130 Bedienungsanleitung

Xtricity

Xtricity 4-80053 Bedienungsanleitung

Stahl

Stahl 6521/4 Series Bedienungsanleitung

Ecosense

Ecosense EcoSpec Bedienungsanleitung

Ayrton

Ayrton minipanel FX Bedienungsanleitung