Degelman LANDROLLER 45 Bedienungsanleitung

1) Drive landroller onto level ground, straight behind the

tractor.

•Ensure there is plenty of room behind and to the sides

of the landroller for backing into ﬁeld position.

2) Remove all ﬁve red transport bars. (4 located on cylinders,

and 1 on ﬂoat hitch).

•Place the transport bars onto the storage brackets

provided and secure with lock-pin.

Note: You may need to activate (extend) the hydraulic cylinders

to allow removal of the cylinder transport bars.

3) Raise the ﬂoatation plate to allow an 1-1/4” gap using

the ratchet jack to place it into ﬁeld “ﬂoat” position.

Float position will allow the hitch pole to contour more

effectively and prevent strain and possible damage to

the machine.

4) Activate the End Wheel Circuit to start lowering the

drums to the ground but stop lowering before the drums

make contact with the ground.

Connect Hydraulics

Backing Into Field Position

142691 v1.0

1-1/4”

ROLLER LIFT CIRCUIT..............End Wheel Cylinders

QUICK-START GUIDE*

for LANDROLLER|45|51

* Refer to operators manual for complete safety and operation info.

WARRANTY

REMEMBER! You must complete Product

Registration to be eligible for Warranty.

CENTER WHEELS..................Center Wheel Cylinders

5) Slowly back-up the landroller spreading the wings until

they are almost fully in ﬁeld position.

8) The roller is now in ﬁeld ready position.

7) Continue backing up until Swing-Arms lock in place.

6) Fully lower the drums to the ground and raise endwheel

struts by closing the hydraulic cylinders & .

6 6

1 2

CMoving Into Transport Position

6) Read and follow necessary safety procedures outlined

in “Transport Safety” section of the manual.

5) Close the ﬂoatation plate using the ratchet jack and

secure into transport position with the red transport pin.

4) Install the four cylinder transport bars onto the center &

end wheel cylinder shafts and secure.

* Refer to operators manual for complete safety and operation info.

• Check for missing, worn or damaged parts.

• Working points & pins

• Hydraulic Connections & Hoses

• Hubs & Spindles

Maintenance

(Check Machine Daily)

1) On level ground, extend center wheel lift cylinders to

fully lift rollers off ground. (This will tighten autofold

cables and open the “Swing Arm” latches.)

2) Extend end wheel circuit to fully lift wing rollers off the

ground.

3) Drive forward until roller wings trail behind.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Degelman Landwirtschaftliche Geräte Handbücher

Degelman

Degelman PRO-CAST 80 Bedienungsanleitung

Degelman

Degelman Pro-till 20 Programmierhandbuch

Degelman

Degelman shuttlekart 1150 Programmierhandbuch

Degelman

Degelman STRAWMASTER 50 Programmierhandbuch

Degelman

Degelman STRAWMASTER 700 Series Bedienungsanleitung

Degelman

Degelman R570P Programmierhandbuch

Degelman

Degelman STRAWMASTER 7000 Bedienungsanleitung

Degelman

Degelman 9075 Programmierhandbuch

Degelman

Degelman REV1500 Programmierhandbuch

Degelman

Degelman PRO-TILL 14 Bedienungsanleitung

Degelman

Degelman PRO-TILL 41 Bedienungsanleitung

Degelman

Degelman Signature 6000 Bedienungsanleitung

Degelman

Degelman PRO-TILL 10/13 Bedienungsanleitung

Degelman

Degelman 5900 Series Bedienungsanleitung

Degelman

Degelman Pro-Till 33 Programmierhandbuch

Degelman

Degelman STRAWMASTER 7000 Bedienungsanleitung

Degelman

Degelman ROCK DIGGER RD320 Programmierhandbuch

Degelman

Degelman M28 Programmierhandbuch

Degelman

Degelman STRAWMASTER PRO Series Bedienungsanleitung

Degelman

Degelman Signature Series Programmierhandbuch

Degelman

Degelman PRO-TILL SCORPION HITCH Programmierhandbuch

Degelman

Degelman STRAWMASTER+ 70 Programmierhandbuch

Degelman

Degelman PRO-TILL 33/40 Bedienungsanleitung

Degelman

Degelman STRAWMASTER PRO 80 Programmierhandbuch

Beliebte Landwirtschaftliche Geräte Handbücher anderer Marken

GSi

GSi PNEG-2314 Bedienungsanleitung

Checchi & Magli

Checchi & Magli TEXDRIVE Bedienungsanleitung

Amazone

Amazone Cenius 4003-2TX Bedienungsanleitung

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Bedienungsanleitung

Cima

Cima BLITZ Bedienungs- und Wartungsanleitung

Amazone

Amazone CombiDisc 3000 Montageanleitung

HE-VA

HE-VA Disc-Roller XL Contour Bedienungsanleitung

AGT

AGT AGT-SSFM Bedienungsanleitung

Milestone

Milestone 72-84 Bedienungsanleitung

KUHN

KUHN Hector 3000 Bedienungsanleitung

Krone

Krone X-Disc 6200 Bedienungsanleitung

Eliet

Eliet DZC450 Bedienungsanleitung

Taarup

Taarup BIO+ B4000 Bedienungsanleitung

Garland

Garland SHAKER 310 DPG Bedienungsanleitung

stable comfort

stable comfort StableWall System Bedienungsanleitung

Raven

Raven AccuBoom Bedienungsanleitung

International

International 710 Bedienungsanleitung

Ashland

Ashland HDW-3217-14 Bedienungsanleitung