Dell SC4020 Bedienungsanleitung
Dell™ SC4020
Storage Controller
Getting Started
With Your System
Regulatory Model Series E10J
Notes, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you make
better use of your Storage Center.
CAUTION: A CAUTION indicates potential damage to hardware or loss of
data if instructions are not followed.
WARNING: A WARNING indicates a potential for property damage,
personal injury, or death.
Contacting Dell Technical Support Services
For technical support, go to support.dell.com/compellent/.
____________________
Information in this document is subject to change without notice.
Reproduction of these materials in any manner whatsoever without the written permission
of Dell Inc. is strictly forbidden.
Copyright © 2013–2014 Dell Inc. All rights reserved. This product is protected by U.S. and
international copyright and intellectual property laws. Dell and the Dell logo are trademarks
of Dell Inc. in the United States and/or other jurisdictions. All other marks and names
mentioned herein may be trademarks of their respective companies.
March 2014 P/N 667T7 Rev. A00
Getting Started With Your System 1
Installation and Configuration
WARNING: Before performing the following procedure, review the safety
instructions that came with all Storage Center components.
WARNING: Battery pack MUST be removed before the controller is
removed from the enclosure.
WARNING: Installing an incompatible battery on the server board may
increase the risk of fire or explosion. Observe the following precautions:
•
The battery should only be replaced with a battery that is the same or
equivalent as the factory installed battery.
•
Do not attempt to open or service the battery. Do not dispose of the
battery in a fire or with household waste. Contact the local waste
disposal agency for the location of the nearest battery deposit site.
Laser Safety statement
The unit is certified in the U.S. to conform to the requirements of DHHS
21 CFR, chapter 1 Subchapter J for Class I (1) laser products, and
elsewhere is certified as a Class I laser product conforming to the
requirements of IEC 60825-1:2007.
Class I laser products are not considered to be hazardous. The laser
system and unit are designed so there is never any human access to
laser radiation above a Class I level during normal operation, user
maintenance or prescribed service condition.
Unpacking the System
NOTE: Unpacking, installing, and deploying your Storage Center may be
done only by a certified service technician.
CAUTION: Class I laser radiation when open, avoid
exposure to the beam.
DANGER: Laser radiation, avoid direct exposure to beam.
2 Getting Started With Your System
Before you begin, make sure the site where you intend to set up and use
the Storage Center has the following:
•
Standard power from an independent source or a rack power
distribution unit with a UPS.
•
Storage Center with the latest firmware, BIOS, and drivers. Contact
your supplier for the correct software versions.
Installation Overview
The installation process follows the general steps below. For detailed
information, refer to vendor documentation supplied with the equipment.
NOTE: The system is intended for restricted access location in
accordance with the National Electric Code, National Standards Institute
(ANSI/National Fire Protection Association (NFPA) 70).
CAUTION: If installed in a closed or multi-unit rack assembly, the
operating ambient temperature of the rack environment may be greater
than room ambient temperature. Therefore, consideration should be given
to installing the equipment in an environment compatible with the maximum
ambient temperature (Tma) specified by the manufacturer. For more
information, see "Technical Specifications" on page 7.
1
Assemble the rails following the safety instructions and the rack
installation instructions provided with your system.
2
Install network switches, as applicable.
3
Install the SC4020 chassis into the rack.
•
Always load the rack from the bottom up for weight stability.
Getting Started With Your System 3
•
You can allow room for expansion if you have fewer than the
maximum number of enclosures.
4
Unwrap and insert each drive into the enclosure one at a time.
•
Protect the drive from static discharge.
•
Handle drives by the edges of the frame.
CAUTION: If the enclosure system operates for more than a few minutes
with missing drives, the enclosure can overheat, causing power failure and
data loss. Such use may invalidate the warranty.
4 Getting Started With Your System
Connecting the Power Cables
1
Ensure that the power switch is in the OFF position before connecting
the power cables.
2
Connect the enclosure power cables to the rack power.
Securing the Power Cables
1
Secure the cables firmly to the bracket using the strap provided.
2
Plug the other end of the power cables into a grounded electrical
outlet or a separate power source such as an uninterrupted power
supply (UPS) or a power distribution unit (PDU).
Getting Started With Your System 5
Location of Power Button
NOTE: Do not power up the enclosure until all Storage Center
components are racked and cabled.
Installing the Bezel
•
Install the bezel.
6 Getting Started With Your System
Other Information You May Need
WARNING: See the safety and regulatory information that shipped with
your Storage Center components. Warranty information may be included
within this document or as a separate document.
•
The rack documentation included with your rack solution describes
how to install your system into a rack.
•
The Storage Center Deployment Guide provides information about
cabling all Storage Center hardware components and configuring a
new Storage Center using the System Manager Setup Wizard.
•
The Storage Center System Manager Administrator’s Guide describes
how to manage a Storage Center.
Andere Handbücher für SC4020
1
Inhaltsverzeichnis
Andere Dell Controller Handbücher
Dell
Dell PowerEdge 2650 Bedienungsanleitung
Dell
Dell USC Bedienungsanleitung
Dell
Dell PowerEdge Series Gebrauchs- und Pflegehandbuch
Dell
Dell Dial Totem Bedienungsanleitung
Dell
Dell iDRAC Anleitung zur Verwendung
Dell
Dell PowerConnect W-620 Bedienungsanleitung
Dell
Dell PowerConnect W-3200 Bedienungsanleitung
Dell
Dell CMC Handbuch
Dell
Dell W-7030 Bedienungsanleitung
Dell
Dell PowerConnect W-6000 Bedienungsanleitung
Dell
Dell Networking W-7024 Bedienungsanleitung
Dell
Dell PowerVault 660F Bedienungsanleitung
Dell
Dell UCS-51 Bedienungsanleitung
Dell
Dell PowerEdge Bedienungsanleitung
Dell
Dell PERC 5/i Bedienungsanleitung
Dell
Dell PowerConnect W-650 Bedienungsanleitung
Dell
Dell PowerEdge M1000e Bedienungsanleitung
Dell
Dell PowerEdge RAID Controller S100 Bedienungsanleitung
Dell
Dell W-7205 Series Bedienungsanleitung
Dell
Dell PowerEdge FX2 Bedienungsanleitung
