Dell EMC Virtual Edge Platform 1405 Series Benutzerhandbuch

Virtual Edge Platform 1405 Series Operating

System Installation Guide

Dell Networking Solutions

July 2021

Rev. A05

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better use of your product.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid

the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

trademarks may be trademarks of their respective owners.

Chapter 1: Introduction................................................................................................................. 4

Chassis physical design...................................................................................................................................................... 4

Chapter 2: Create a serial console connection..............................................................................10

Chapter 3: Create bootable USB drive..........................................................................................12

Chapter 4: Configure BIOS and install Ubuntu 18.04 operating system to SSD............................. 14

Configure BIOS to boot from USB drive...................................................................................................................... 14

Installation of Ubuntu 18.04 operating system to SSD............................................................................................. 15

Configure BIOS to boot from SSD...........................................................................................................................16

Chapter 5: Configure BIOS and install Red Hat Enterprise Linux operating system to SSD...........18

Configure BIOS to boot from USB................................................................................................................................ 18

Install Red Hat Enterprise Linux 7.5 operating system............................................................................................. 18

Start RHEL operating system installation.................................................................................................................... 19

Configure BIOS to boot from SSD.................................................................................................................................19

Chapter 6: Configure BIOS and install ADVA 18.4 operating system installation to SSD................21

Configure BIOS to boot from USB.................................................................................................................................21

Install ADVA 18.4 operating system.............................................................................................................................. 22

Configure BIOS to boot from SSD................................................................................................................................ 23

Chapter 7: Download and install VMware ESXi 7.0....................................................................... 26

Create bootable USB drive for ESXi 7.0......................................................................................................................26

Configure BIOS to boot from USB................................................................................................................................ 27

Install VMware ESXi 7.0 operating system................................................................................................................. 28

Configure BIOS to boot from SSD................................................................................................................................29

Chapter 8: LTE modem detection................................................................................................ 33

LTE modem detection on Versa.................................................................................................................................... 33

LTE modem detection on ADVA.................................................................................................................................... 33

LTE modem detection on ESXi...................................................................................................................................... 34

Contents

Contents 3

Introduction

This document provides the operating system installation steps for the Dell EMC Virtual Edge Platform (VEP) 1405 series of

systems. The steps that are provided have been tested and verified on VEP1405 devices using the following information:

Table 1. Operating system information

Feature Description

Ubuntu operating system image ubuntu-18.04.3-live-server-amd64.iso

Red Hat Enterprise Linux (RHEL)

operating system image

rhel-server-7.5-x86_64-dvd.iso

ESXi 7.0 operating system image VMware-VMvisor-Installer-7.0.0-16324942.x86_64-DellEMC_Customized-A03.iso

ADVA operating system image SVCS_connector-18.4.1.31-18.4-factory-dell-57.iso

The recommended minimum device configuration for the VEP1405 series before installing the operating system is as follows:

Table 2. VEP1405 series recommended minimum firmware versions

Feature Configuration option 1 ( Versa

ready) Configuration option 2 (ADVA ready)

DIAG OS 3.43.3.81-18 3.43.3.81-18

DIAG Tools 3.43.4.81-19 3.43.4.81-19

Firmware Updater 1.6 1.6

BIOS version (4-core) 3.48.0.9-11 (for VEP1405 series)

3.48.0.9-12 (for VEP1405N series)

(4-core option is not available)

BIOS version (8-core and 16-core) 3.48.0.9-11 (for VEP1405 series)

3.48.0.9-12 (for VEP1405N series)

3.48.0.9-11

CPLD version 0.7 0.7

PIC v20J v20J

Chassis physical design

Table 3. Dell EMC Virtual Edge Platform (VEP) 1405 model descriptions

Model CPU Description

VEP1425 4-core ●8 GB DDR4

●16 GB eMMC

●120 GB SSD

●2x 2 Wi-Fi

●6x 1 GB Copper RJ45

●2x 10 GB SFP+

●Versa software installed

●Trusted Platform Module (TPM) 2.0 - World-wide except China

●2x USB 3.0

●Low-energy Bluetooth (BLE)

4 Introduction

Table 3. Dell EMC Virtual Edge Platform (VEP) 1405 model descriptions (continued)

Model CPU Description

●One fan

VEP1425N 4-core ●8 GB DDR4

●16 GB eMMC

●120 GB SSD

●6x 1 GB Copper RJ45

●2x 10 GB SFP+

●Versa software installed

●Trusted Platform Module (TPM) 2.0 - World-wide except China

●2x USB 3.0

●One fan

VEP1445 8-core ●16 GB DDR4

●16 GB eMMC

●240 GB SSD

●2x 2 Wi-Fi

●6x 1 GB Copper RJ45

●2x 10 GB SFP+

●Versa software installed

●Trusted Platform Module (TPM) 2.0 - World-wide except China

●2x USB 3.0

●Low-energy Bluetooth (BLE)

●Two fans

VEP1445 8-core ●32 GB DDR4

●16 GB eMMC

●960 GB SSD

●2x 2 Wi-Fi

●6x 1 GB Copper RJ45

●2x 10 GB SFP+

●ADVA software installed

●Trusted Platform Module (TPM) 2.0 - World-wide except China

●2x USB 3.0

●Low-energy Bluetooth (BLE)

●Two fans

VEP1445N 8-core ●16 GB DDR4

●16 GB eMMC

●240 GB SSD

●6x 1 GB Copper RJ45

●2x 10 GB SFP+

●Versa software installed

●Trusted Platform Module (TPM) 2.0 - World-wide except China

●2x USB 3.0

●Two fans

VEP1485 16-core ●32 GB DDR4

●16 GB eMMC

●240 G SSD

●2x 2 Wi-Fi

●6x 1 GB Copper RJ45

●2x 10 GB SFP+

●Versa software installed

●Trusted Platform Module (TPM) 2.0 - World-wide except China

●2x USB 3.0

●Low-energy Bluetooth (BLE)

Introduction 5

Table 3. Dell EMC Virtual Edge Platform (VEP) 1405 model descriptions (continued)

Model CPU Description

●Two fans

VEP1485 16-core ●64 GB DDR4

●16 GB eMMC

●2 TB SSD

●2x 2 Wi-Fi

●6x 1 GB Copper RJ45

●2x 10 GB SFP+

●ADVA software installed

●Trusted Platform Module (TPM) 2.0 - World-wide except China

●2x USB 3.0

●Low-energy Bluetooth (BLE)

●Two fans

VEP1485N 16-core ●32 GB DDR4

●16 GB eMMC

●240 G SSD

●6x 1 GB Copper RJ45

●2x 10 GB SFP+

●Versa software installed

●Trusted Platform Module (TPM) 2.0 - World-wide except China

●2x USB 3.0

●Two fans

NOTE: For a listing of the supported optics guidelines for the VEP1405 series, see the Virtual Edge Platform 1405 Series

Technology Guide.

Figure 1. VEP1405 series front view

1. Security lock port

2. USB port

NOTE: An additional USB port is located on the opposite side of the system.

3. System status indicator LED

Table 4. Front view system status indicator LED

Color Status

Red Power on

White System is booting

Green Operating system boots with diagOS

Blue Reset button is pressed for more than five seconds

NOTE: See the Reset button behavior table below for more information.

6 Introduction

Figure 2. VEP1405 series rear view (with port cover)

1. Port cover

2. Reset button

NOTE: See the Reset button behavior table below for more information.

3. LED status indicators for SFP+ ports

4. SFP+ ports

5. Ethernet ports and LED status indicators

6. Power connection port

NOTE: To prevent the VEP1405 series system console port from being accessed in a nonsecure location, the system

ships from the factory with a plate covering the micro USB port. To uncover the port, use a #0 (2.5 mm) Phillips head

screwdriver to loosen or remove the screw that holds the plate in place.

Figure 3. VEP1405 series back view (without port cover)

1. Micro USB serial console port

2. Reset button

NOTE: See the Reset button behavior table below for more information.

3. LED status indicators for SFP+ ports

4. SFP+ ports

5. Ethernet ports and LED status indicators

6. Power connection port

Introduction 7

Table 5. Back view system status indicator LED behavior

Class Behavior

1000M Base-T LED ●Link LED - Green or amber

○Solid green - Port is linked and running at maximum 1000M

speed on Base-T port

○Solid amber - Port is linked and running at lower 100M or 10M

speed on Base-T port

○Off - No link

●Activity LED - Green

NOTE: The LED flashes green during port activity.

○Off - no port activity

SFP+ LED ●Link LED - Green or amber

○Solid green - Port is linked and running at 10G speed

○Solid amber - Port is linked and running at 1G speed

○Off - No link

●Activity LED - Green

NOTE: The LED flashes green during port activity.

○Off - no port activity

Table 6. Reset button behavior

Action Behavior

Press the Reset button for less than 5 seconds: ●System reboots

Press the Reset button for more than 5 seconds: ●System reboots and system is reset to factory defaults

●Status indicator LED color changes to blue

●Flag indicating a long push is set by the BIOS in the CMOS RAM

●Flag allows user to have the operating system detect a long button

push

Table 7. Chassis physical design

Parameter Configuration option 1 Configuration option 2

Height 5.2 cm (2.0 in) 5.2 cm (2.0 in)

Width 20.8 cm (8.1 in) 20.8 cm (8.1 in)

Depth 20.0 cm (7.9 in) 20.0 cm (7.9 in)

Chassis weight with factory-

installed components

●4-core: 1.44 kg (3.17 lb)

●8-core: 1.42 kg (3.13 lb)

●16-core: 1.44 kg (3.17 lb)

●8-core: 1.42 kg (3.13 lb)

●16-core: 1.44 kg (3.17 lb)

NOTE: Chassis weight does not include the weight of the power supply.

Table 8. Environmental parameters

Parameter Configuration option 1 Configuration option 2

Operating temperature 0–40°C (32°F–104°F) continuously 0–40°C (32°F–104°F) continuously

Operating humidity ●5% to 85% (RH), noncondensing

continuously

●5% to 90% (RH), noncondensing short-

term (< 1% of operational hour per year)

●5% to 85% (RH), noncondensing

continuously

●5% to 90% (RH), noncondensing short-

term (< 1% of operational hour per year)

Storage temperature –40°-70°C (–40° to 158°F) –40°-70°C (–40° to 158°F)

Storage humidity 5% to 90% (RH), noncondensing 5% to 90% (RH), noncondensing

8 Introduction

Table 8. Environmental parameters (continued)

Parameter Configuration option 1 Configuration option 2

Maximum operational altitude 3,048 meters (10,000 ft) with no

performance degradation to 950 meters

(3117 ft)

3,048 meters (10,000 ft) with no performance

degradation to 950 meters (3117 ft)

Maximum nonoperational

altitude

10,668 meters (35,000 ft) 10,668 meters (35,000 ft)

Table 9. AC power requirements

Parameter Configuration option 1 Configuration option 2

Power supply 100–240 VAC 50/60 Hz 100–240 VAC 50/60 Hz

Maximum current draw per

system - AC

●100 VAC: 2.0A

●240 VAC: 1.0A

●100 VAC: 2.0A

●240 VAC: 1.0A

Power consumption Typical:

●40 W (16 core)

●35 W (8 core)

●20 W (4 core)

Maximum:

●50 W (16 core)

●45 W (8 core)

●30 W (4 core)

Typical:

●40 W (16 core)

●35 W (8 core)

Maximum:

●50 W (16 core)

●45 W (8 core)

NOTE: For the most current AC power requirements and power consumption specifications, see the Installation Guide at

https://www.dell.com/support.

Introduction 9

Create a serial console connection

NOTE: The instructions provided in this section are intended for use on a system that is running a Microsoft Windows

operating system.

To create a serial console connection, perform the following steps:

1. Use a micro USB to USB type-A cable to establish a connection between the VEP1405 series micro USB console port and

the personal computer.

NOTE: Ensure that you have the driver for the CP210X USB - UART Bridge VCP from Silicon Labs installed. For more

information or to download the necessary driver, see https://www.silabs.com/products/development-tools/software/

usb-to-uart-bridge-vcp-drivers.

2. Check the CP2102 drive communications port using the Microsoft Windows operating system Device Manager.

Figure 4. Microsoft Windows Device Manager

3. Using a terminal emulator such as PuTTY, locate and configure the serial port that the USB connection represents.

4. In the Serial field, enter the wanted connection name.

5. Enter 115200 as the baud rate, in the Speed field.

6. Select Serial for the Connection type.

NOTE: To save the selected options for future use, enter a name in the Saved Sessions field then click Save.

Figure 5. PuTTY configuration screen

7. Click Open.

NOTE: Steps 8 and 9 provide instructions on how to access the BIOS setup screen.

8. Plug the VEP1405 system power cable into a power source.

The unit immediately starts to power up. Watch for the VEP1405 console window. The POST Lower DRAM Memory test

screen displays a cursor.

10 Create a serial console connection

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Dell Netzwerk-Hardware Handbücher

Dell

Dell PowerVault NX3610 Bedienungsanleitung

Dell

Dell SonicWALL SuperMassive 9600 Bedienungsanleitung

Dell

Dell PowerProtect DM5500 Bedienungsanleitung

Dell

Dell VxRail P670F Handbuch

Dell

Dell Secure Mobile Access 6200 Bedienungsanleitung

Dell

Dell FS7500 Handbuch

Dell

Dell PowerConnect W-620 Bedienungsanleitung

Dell

Dell XC720xd Bedienungsanleitung

Dell

Dell 5821E Bedienungsanleitung

Dell

Dell XC430 Bedienungsanleitung

Dell

Dell 210-APGV Bedienungsanleitung

Dell

Dell PowerEdge XR4000z Handbuch

Dell

Dell VxRail G560 Bedienungsanleitung

Dell

Dell PowerVault NX1950 Bedienungsanleitung

Dell

Dell Safeguard 5242LR Bedienungsanleitung

Dell

Dell PowerVault 124T Bedienungsanleitung

Dell

Dell 53-1002116-01 Service-Handbuch

Dell

Dell AX150 Referenzhandbuch

Dell

Dell SonicPoint-N Dual Radio Bedienungsanleitung

Dell

Dell Edge 3000 Series Bedienungsanleitung

Dell

Dell PowerVault 122T SDLT 320 Bedienungsanleitung

Dell

Dell PowerEdge XR4000r Handbuch

Dell

Dell Broadcom NetXtreme Family of Adapters Bedienungsanleitung

Dell

Dell MC SD-WAN Edge 3400 Advanced Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung