Dell PowerEdge 1750 Bedienungsanleitung

www.dell.com | support.dell.com

Dell™ Systems

Installing or Replacing

an ERA/O Card

安装或更换 ERA/O 卡

Installation ou remplacement d'une carte ERA/O

Installieren oder Austauschen einer ERA/O-Karte

ERA/O カードの取り付けおよび取り外し

ERA/O 카드 설치 또는 교체

Instalación o sustitución de una tarjeta ERA/O

K0238fc0.fm Page 1 Monday, February 24, 2003 2:46 PM

K0238fc0.fm Page 2 Monday, February 24, 2003 2:46 PM

www.dell.com | support.dell.com

Dell™ Systems

Installing or Replacing

an ERA/O Card

K0238ebk0.book Page 1 Monday, February 24, 2003 2:53 PM

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you

how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury,

or death.

____________________

Information in this document is subject to change without notice.

Reproductioninanymannerwhatsoever without the written permissionofDellComputerCorporationisstrictlyforbidden.

Trademarks used in this text: Dell, PowerEdge, and the DELL logo are trademarks of Dell Computer Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and

names or their products. Dell Computer Corporation disclaims any proprietary interest in trademarks and trade names

other than its own.

February 2003 P/N K0238 Rev. A00

K0238ebk0.book Page 2 Monday, February 24, 2003 2:53 PM

Installing or Replacing an ERA/O Card 1-1

This document explains how to install and remove your system’s Embedded Remote Access

Option (ERA/O) card.

Before You Begin

NOTE: For more information about setting up and using an ERA/O card, see the

remote access controller (RAC) documentation provided on the documentation CD that

came with your system or on the Dell Support website at support.dell.com.

NOTE: The Dell™ Remote Access Card III (DRAC III), DRAC III/XT, Embedded

Remote Access (ERA), and the ERA/O are systems management hardware and

software solutions designed to provide remote management capabilities for

PowerEdge™ systems. Collectively, these solutions are known as remote access

controllers (RACs). RACs allow you to remotely manage and monitor your system even

when the system is down.

Before installing the ERA/O card, record the system configuration settings. View the system

configuration screens in the System Setup program and make a note of each setting. See

your User's Guide for instructions about using the System Setup program.

Installing an ERA/O Card

CAUTION: Only trained service technicians are authorized to remove the system

cover and access any of the components inside the system. See your System

Information Guide for complete information about safety precautions, working

inside the computer, and protecting against electrostatic discharge.

1Remove the optional front bezel (if applicable).

2Turn off the system, including attached peripherals, and disconnect the system and

peripherals from their electrical outlets.

3Remove the optional security screw (if applicable). See Figure 1-1.

4Press the latch on the system front panel and lift the left cover.

5Lift the right cover.

K0238ebk0.book Page 1 Monday, February 24, 2003 2:53 PM

1-2 Installing or Replacing an ERA/O Card

www.dell.com | support.dell.com

Figure 1-1. Opening the System Covers

6Remove the SCSI backplane board:

aPull each hard-drive carrier partially out of its slot, approximately 2.5 cm (1 inch).

bDisconnect the diskette-drive interface cable from the FLOPPY connector on the

backplane board. See Figure 1-2.

cDisconnect the CD drive interface cable from the CD_ROM connector on the

backplane board. See Figure 1-2.

dPress the release latch in toward the backplane board and use the handle to pull

the board out of its connector and up out of the chassis. See Figure 1-2.

latch

optional security screw

right cover

left cover

K0238ebk0.book Page 2 Monday, February 24, 2003 2:53 PM

Installing or Replacing an ERA/O Card 1-3

Figure 1-2. SCSI Backplane Board

7If the system has an optional ROMB card installed, remove the ROMB backup battery

(not the ROMB card itself) to expose the ERA/O card connector.

See Figure 1-3; see also "Removing a ROMB Card" in your Installation and

Troubleshooting Guide.

8Unpack the ERA/O card.

If you are replacing an ERA/O card, see "Removing an ERA/O Card" for removal

instructions before continuing with the next step.

CD drive interface

connector (CD_ROM)

diskette drive interface connector

(FLOPPY)

handle

release latch

tabs (2)

K0238ebk0.book Page 3 Monday, February 24, 2003 2:53 PM

1-4 Installing or Replacing an ERA/O Card

www.dell.com | support.dell.com

Figure 1-3. Removing the ROMB Backup Battery

9Install the ERA/O card in the ERA/O card connector (EMBEDDED_REMOTE_

ASSISTANT) on the system board. See Figure 1-4.

aAlign the connector on the bottom of the ERA/O card with the ERA/O connector

on the system board; align the holes along the edges of the card with the center

posts of the four retention clips on the system board.

bPress the card down into the connector and onto the retention clip posts until the

clips snap into place around the card and the card is fully seated into the

connector.

ROMB backup

battery

RAID BATTERY connector

battery standoffs (2)

ROMB card

ERA/O card

connector

K0238ebk0.book Page 4 Monday, February 24, 2003 2:53 PM

Installing or Replacing an ERA/O Card 1-5

Figure 1-4. Installing the ERA/O Card

10 If you removed a ROMB backup battery in step 7, replace the battery. See Figure 1-3;

also see "Installing a ROMB Card" in your Installation and Troubleshooting Guide.

11 Replace the SCSI backplane. See Figure 1-2.

aFit the metal tabs at each end of the backplane into the slots in the chassis wall,

and lower the backplane into the chassis, ensuring that the CD and diskette drive

interface cables are not caught under the backplane.

bPress down firmly over the handle to seat the backplane in its connector.

cPivot the release latch out into the securing slot in the chassis.

dConnect the CD drive interface cable to the CD_ROM connector on the

backplane board.

eConnect the diskette-drive interface cable to the FLOPPY connector on the

backplane board.

fPress all installed hard drives firmly back into the SCSI connectors on the

backplane.

12 Close the system covers.

When closing the covers, close the right (larger) cover first and then close the left

cover. Press firmly on the left cover to snap the securing latch into place.

13 Install the optional security screw (if applicable). See Figure 1-1.

ERA/O card

retention clips (4)

ERA/O card connector

K0238ebk0.book Page 5 Monday, February 24, 2003 2:53 PM

1-6 Installing or Replacing an ERA/O Card

www.dell.com | support.dell.com

14 Reconnect the system and peripherals to their electrical outlets, and turn them on.

15 Install the optional front bezel (if applicable).

16 If the 100-Mbps RAC Ethernet connector on the back of the system has not been used

before, you must remove the thin plastic cover that protects the connector.

You can insert your finger underneath the silver strip at the top of the cover to tear

away the cover. See Figure 1-5 for the location of the connector.

17 Connect a network cable to the RAC Ethernet connector. See Figure 1-5.

Figure 1-5. RAC Ethernet Connector

18 Update the ERA/O card with the latest version of the ERA/O firmware, available at the

Dell Support website at support.dell.com.

See the RAC documentation provided on the documentation CD for

information about updating the firmware.

RAC Ethernet connector

K0238ebk0.book Page 6 Monday, February 24, 2003 2:53 PM

Andere Handbücher für PowerEdge 1750

Inhaltsverzeichnis

Sprachen:

Andere Dell Server Handbücher

Dell

Dell PowerEdge M910 Kurzanleitung

Dell

Dell PowerEdge C6220 Bedienungsanleitung

Dell

Dell DX6012S Bedienungsanleitung

Dell

Dell PowerEdge R805 System Bedienungsanleitung

Dell

Dell PowerEdge C5230 Bedienungsanleitung

Dell

Dell E28S Series Bedienungsanleitung

Dell

Dell Wyse 3030 LT Bedienungsanleitung

Dell

Dell EMC VxFlex Ready Node 14G Bedienungsanleitung

Dell

Dell 6100 Leitfaden

Dell

Dell PowerEdge R905 Bedienungsanleitung

Dell

Dell PowerEdge B02S Bedienungsanleitung

Dell

Dell PowerEdge C5230 Bedienungsanleitung

Dell

Dell E69S001 Bedienungsanleitung

Dell

Dell PowerEdge T420 Bedienungsanleitung

Dell

Dell PowerEdge C6105 Bedienungsanleitung

Dell

Dell EMC PowerEdge R740 Handbuch

Dell

Dell PowerEdge SC1435 Technisches Handbuch

Dell

Dell PowerEdge 1650 Bedienungsanleitung

Dell

Dell PowerEdge T105 Systems Bedienungsanleitung

Dell

Dell PowerEdge R450 Bedienungsanleitung

Dell

Dell PowerEdge T605 Bedienungsanleitung

Dell

Dell EMC PowerEdge C6420 Handbuch

Dell

Dell PowerEdge R715 Bedienungsanleitung

Dell

Dell PowerEdge R730 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Planet

Planet NAS-7410 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR635 V3 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY BX900 Bedienungsanleitung

Asus

Asus RS700DA-E6 PS4 Bedienungsanleitung

Vertiv

Vertiv Avocent ACS6000 Montage- und Wartungsanleitung

A & T Internationale

A & T Internationale Xserve Service-Handbuch