Dell PowerEdge 2650 Bedienungsanleitung

www.dell.com | support.dell.com

Dell™ Systems

Rack Installation Guide

Guide d'installation du rack

Rack-Installationsanleitung

ラック取り付けガイド

Guía de instalación del estante

www.dell.com | support.dell.com

Dell™ Systems

Rack Installation Guide

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you

how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury,

or death.

____________________

Information in this document is subject to change without notice.

Reproductioninanymannerwhatsoever without the written permissionofDellComputerCorporationisstrictlyforbidden.

Trademarks used in this text: Dell, the DELL logo, RapidRails, and VersaRails are trademarks of Dell Computer

Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and

names or their products. Dell Computer Corporation disclaims any proprietary interest in trademarks and trade names

other than its own.

October 2002 P/N 7W226 Rev. A00

Contents 3

Contents

CAUTION: Safety Instructions . . . . . . . . . . . . . . . . . . 1-1

Rack Mounting of Systems. . . . . . . . . . . . . . . . . . . 1-1

Installation Instructions . . . . . . . . . . . . . . . . . . . . . 1-2

Four-Post Rack Installation . . . . . . . . . . . . . . . . . . . . 1-3

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . 1-3

Recommended Tools and Supplies . . . . . . . . . . . . . . . 1-4

RapidRails Rack Kit Contents . . . . . . . . . . . . . . . . . 1-4

VersaRails Rack Kit Contents . . . . . . . . . . . . . . . . . 1-5

Installation Tasks . . . . . . . . . . . . . . . . . . . . . . . 1-5

Removing the Rack Doors . . . . . . . . . . . . . . . . . . . 1-6

Marking the Rack . . . . . . . . . . . . . . . . . . . . . . . 1-6

Installing the RapidRails Slide Assemblies . . . . . . . . . . . 1-8

Installing the VersaRails Slide Assemblies . . . . . . . . . . 1-10

Installing the System in the Rack . . . . . . . . . . . . . . 1-11

Installing the Cable-Management Arm. . . . . . . . . . . . 1-13

Routing Cables . . . . . . . . . . . . . . . . . . . . . . . 1-16

Replacing the Rack Doors . . . . . . . . . . . . . . . . . . 1-17

Two-Post Rack Installation . . . . . . . . . . . . . . . . . . . 1-18

Two-Post Rack Installation Tasks . . . . . . . . . . . . . . 1-18

Recommended Tools and Supplies . . . . . . . . . . . . . . 1-19

Rack Kit Contents . . . . . . . . . . . . . . . . . . . . . . 1-19

Marking the Rack . . . . . . . . . . . . . . . . . . . . . . 1-20

Installing the Slide Assemblies in the Rack. . . . . . . . . . 1-22

Installing the System in the Rack . . . . . . . . . . . . . . 1-27

Installing the Cable-Management Arm. . . . . . . . . . . . 1-27

Routing Cables . . . . . . . . . . . . . . . . . . . . . . . 1-27

4Contents

Figures

Figure 1-1. RapidRails Rack Kit Contents . . . . . . . . . 1-4

Figure 1-2. VersaRails Rack Kit Contents . . . . . . . . . 1-5

Figure 1-3. One Rack Unit . . . . . . . . . . . . . . . . . 1-7

Figure 1-4. Marking the Vertical Rails . . . . . . . . . . 1-8

Figure 1-5. Installing the RapidRails Slide Assemblies . . . 1-9

Figure 1-6. Installing the VersaRails Slide Assemblies . . 1-11

Figure 1-7. Installing the System in the Rack

(RapidRails or VersaRails) . . . . . . . . . 1-12

Figure 1-8. Installing the Cable-Management Arm . . . 1-14

Figure 1-9. Installing the Cable-Management Arm . . . 1-15

Figure 1-10. Routing the Power Cords . . . . . . . . . . 1-16

Figure 1-11. Routing Cables . . . . . . . . . . . . . . . 1-17

Figure 1-12. Two-Post Rack Kit Components . . . . . . . 1-19

Figure 1-13. Two-Post, Open-Frame Relay Rack

Universal-Hole Spacing . . . . . . . . . . . 1-20

Figure 1-14. Two-Post, Open-Frame Relay Rack

Wide-Hole Spacing . . . . . . . . . . . . . 1-21

Figure 1-15. Installing the Slide Assemblies for

Center-Mount Configuration . . . . . . . . 1-23

Figure 1-16. Rotating the Front Mounting Bracket for

Flush-Mount Installation . . . . . . . . . . 1-25

Figure 1-17. Installing the Slide Assemblies for

Flush-Mount Configuration . . . . . . . . . 1-26

Rack Installation Guide 1-1

CAUTION: Safety Instructions

Use the following safety guidelines to help ensure your own personal safety and to help

protect your system and working environment from potential damage. For complete safety

information, see the System Information Guide.

Rack Mounting of Systems

Observe the following precautions for rack stability and safety.

Systems are considered to be components in a rack. Thus, "component" refers to any

system as well as to various peripherals or supporting hardware.

CAUTION: Installing systems in a rack without the front and side stabilizers

installed could cause the rack to tip over, potentially resulting in bodily injury

under certain circumstances. Therefore, always install the stabilizers before

installing components in the rack.

After installing system/components in a rack, never pull more than one

component out of the rack on its slide assemblies at one time. The weight of

more than one extended component could cause the rack to tip over and may

result in serious injury.

NOTE: Your system is safety-certified as a free-standing unit and as a component for

use in a Dell™ rack cabinet using the customer rack kit. The installation of your

system and rack kit in any other rack cabinet has not been approved by any safety

agencies. It is your responsibility to ensure that the final combination of system and

rack complies with all applicable safety standards and local electric code

requirements. Dell disclaims all liability and warranties in connection with such

combinations.

• System rack kits are intended to be installed in a rack by trained service technicians. If

you install the kit in any other rack, be sure that the rack meets the specifications of a

Dell rack.

CAUTION: Do not move racks by yourself. Due to the height and weight of the

rack, a minimum of two people should accomplish this task.

• Before working on the rack, make sure that the stabilizers are secured to the rack,

extended to the floor, and that the full weight of the rack rests on the floor. Install

front and side stabilizers on a single rack or front stabilizers for joined multiple racks

before working on the rack.

• Always load the rack from the bottom up, and load the heaviest item in the rack first.

• Make sure that the rack is level and stable before extending a component from the

rack.

1-2 Rack Installation Guide

www.dell.com | support.dell.com

Installation Instructions

This installation guide provides instructions for trained service technicians installing one or

more systems in an open-frame relay rack or in a rack cabinet. The RapidRails™ rack kit can

be installed in all the manufacturer’s rack cabinets without tools, and the VersaRails™ rack

kit can be installed in many industry-standard rack cabinets. The procedures for installing

both RapidRails and VersaRails rack kits are similar. One rack kit is required for each system

to be installed in the rack cabinet.

This guide includes procedures for the following rack kits:

• RapidRails kit in a four-post rack cabinet

• VersaRails kit in a four-post rack cabinet

• Two-post kit (installed in either center-mount or flush-mount configuration, for 3- or

6-inch-wide racks)

For ease in troubleshooting and the identification of system health, these rack kits include a

status-indicator cable that extends the information on the two-color status indicators on

the front and back panels to the back of the cable-management arm. For more information

on these indicators, see your system User’s Guide.

Before attempting this installation, you should read through this entire document carefully.

CAUTION: Do not install rack kit components designed for another system. Use

only the rack kit for your system. Using the rack kit for another system may

result in damage to the system and personal injury to yourself and to others.

• Use caution when pressing the component rail release latches and sliding a

component into or out of a rack; the slide rails can pinch your fingers.

• After a component is inserted into the rack, carefully extend the rail into a locking

position, and then slide the component into the rack.

• Do not overload the AC supply branch circuit that provides power to the rack. The

total rack load should not exceed 80 percent of the branch circuit rating.

• Ensure that proper airflow is provided to components in the rack.

• Do not step on or stand on any component when servicing other components in a

rack.

CAUTION: Safety Instructions (continued)

Rack Installation Guide 1-3

Rack Requirements for VersaRails

NOTICE: The VersaRails rack kit is intended to be installed by trained service

technicians in a rack that meets the specifications of American National

Standards Institute (ANSI)/Electronic Industries Association (EIA) standard

ANSI/EIA-310-D-92, International Electrotechnical Commission (IEC) 297, and

Deutsche Industrie Norm (DIN) 41494. One rack kit is required for each system that

is installed in a rack.

Four-Post Rack Installation

Before attempting this installation, you should read through this entire procedure carefully.

Before You Begin

Before you begin installing your system in the rack, carefully read "CAUTION: Safety

Instructions," found earlier in this guide, as well as the safety instructions found in your

system’s System Information document for additional information.

CAUTION: When installing multiple systems in a rack, complete all of the

procedures for the current system before attempting to install the next system.

CAUTION: Rack cabinets can be extremely heavy and move easily on the casters.

The cabinet has no brakes. Use extreme caution while moving the rack cabinet.

Retract the leveling feet when relocating the rack cabinet. Avoid long or steep

inclines or ramps where loss of cabinet control may occur. Extend the leveling

feet for support and to prevent the cabinet from rolling.

Important Safety Information

Observe the safety precautions in the following subsections when installing your system in

the rack.

CAUTION: You must strictly follow the procedures in this document to protect

yourself as well as others who may be involved. Your system may be very large

and heavy, and proper preparation and planning are important to prevent injury

to yourself and to others. This becomes increasingly important when systems are

installed high up in the rack.

Rack Stabilizer Feet

CAUTION: Installing systems in a rack without the front and side stabilizer feet

installed could cause the rack to tip over, potentially resulting in bodily injury

under certain circumstances. Therefore, always install the stabilizer feet before

installing components in the rack.

1-4 Rack Installation Guide

www.dell.com | support.dell.com

CAUTION: After installing systems in a rack, never pull more than one system

out of the rack on its slide assemblies at one time. The weight of more than one

extended system could cause the rack to tip over and cause injury.

The stabilizer feet help prevent the rack from tipping over when a system or other

component is pulled out of the rack with the slide assemblies fully extended. Refer to the

documentation provided with the rack cabinet for instructions on installing and anchoring

the stabilizer feet.

Recommended Tools and Supplies

You may need the following tools and supplies to install the system in a four-post rack:

• A #2 Phillips screwdriver (for installing VersaRails slide assemblies)

• Masking tape or a felt-tip pen, for use in marking the mounting holes to be used

RapidRails Rack Kit Contents

The RapidRails rack kit includes the following items (see Figure 1-1):

• One pair of RapidRails slide assemblies

• One cable-management arm

• One status indicator cable

• Tie-wraps (not shown in Figure 1-1)

Figure 1-1. RapidRails Rack Kit Contents

slide assemblies (2)

cable-management arm

status indicator cable

Andere Handbücher für PowerEdge 2650

Inhaltsverzeichnis

Sprachen:

Andere Dell Server Handbücher

Dell

Dell FC4700 Bedienungsanleitung

Dell

Dell PowerEdge R530 Bedienungsanleitung

Dell

Dell PowerEdge 2450 Bedienungsanleitung

Dell

Dell Wyse7020 Bedienungsanleitung

Dell

Dell PowerVault NX3500 Service-Handbuch

Dell

Dell PowerEdge 2800 Handbuch

Dell

Dell PowerEdge 2550 Bedienungsanleitung

Dell

Dell PowerEdge 4350 Bedienungsanleitung

Dell

Dell PowerEdge 2550 Bedienungsanleitung

Dell

Dell PowerEdge SE400 Bedienungsanleitung

Dell

Dell PowerVault NX200 Bedienungsanleitung

Dell

Dell 8 Bedienungsanleitung

Dell

Dell EMC PowerEdge R650xs Bedienungsanleitung

Dell

Dell PowerEdge R760xa Handbuch

Dell

Dell PowerEdge 1600SC Bedienungsanleitung

Dell

Dell PowerEdge XR12 Handbuch

Dell

Dell PowerEdge R610 Bedienungsanleitung

Dell

Dell PowerEdge 6850 Bedienungsanleitung

Dell

Dell FORCE10 Open Automation Kurzanleitung

Dell

Dell PowerEdge R320 Bedienungsanleitung

Dell

Dell PowerEdge R230 Bedienungsanleitung

Dell

Dell PowerEdge M1000e Bedienungsanleitung

Dell

Dell PowerEdge C6615 Handbuch

Dell

Dell PowerEdge 4600 Technisches Handbuch

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Planet

Planet NAS-7410 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR635 V3 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY BX900 Bedienungsanleitung

Asus

Asus RS700DA-E6 PS4 Bedienungsanleitung

Vertiv

Vertiv Avocent ACS6000 Montage- und Wartungsanleitung

A & T Internationale

A & T Internationale Xserve Service-Handbuch