Dell PowerEdge 800 Technisches Handbuch

www.dell.com | support.dell.com

Dell™ PowerEdge™ 800 Systems

Information Update

信息更新

Mise à jour des informations

Aktuelle Informationen

アップデート情報

정보 업데이트

Actualización de información

www.dell.com | support.dell.com

Dell™ PowerEdge™ 800 Systems

Information Update

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you

how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.

Abbreviations and Acronyms

For a complete list of abbreviations and acronyms, see the "Glossary" in your

User’s Guide

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, and PowerEdge are trademarks of Dell Inc.; Intel is a registered trademark

of Intel Corporation; Red Hat is a registered trademark of Red Hat, Inc.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names

or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

October 2004 P/N H6440 Rev. A01

Information Update 3

This document provides updated information for your system on the following topics:

• Broadcom driver limitation with Red Hat

Linux

• Using DRAC 4/P with Red Hat Enterprise Linux 3 (RHEL 3)

• 64-bit capability

• Microprocessor replacement

Broadcom Driver Limitation With Red Hat Linux

On systems running the Red Hat Linux operating system, if you use the IPMI Pass Through

(IPMI PT) for remote manageability over a LAN and you want to configure VLAN, you must use

the Broadcom Advanced Server Program (BASP) and bcm5700 driver instead of the native Linux

tg3 driver. If you use the native Linux tg3 driver with IPMI PT enabled, the VLAN functionality

will not work correctly. The operating system utilities will let you configure the VLANS, but you

will not receive any traffic over the VLAN interface.

Using DRAC 4/P With Red Hat Enterprise Linux 3

If your system has a DRAC 4/P card installed, the integrated IDE controllers and their devices will

not be available on systems running RHEL 3. As a temporary solution, append the following kernel

parameter to the kernel line for each stanza in the

grub.conf

file:

ide2=0x1f0

. As an alternative,

go to

rhn.redhat.com

and upgrade your kernel to version 2.4.21.15.EL or higher.

64-Bit Capability

If the processor installed in your system has 64-bit capability, the

64-bit Technology

option on the

CPU Information

screen in the System Setup program will show

Yes (Intel

EM64T)

. If your

system has a 32-bit processor installed, the

64-bit Technology

option will show

. This field

specifies if the installed processor supports Intel 64-bit technology.

Microprocessor Replacement

You can upgrade the system processor to take advantage of future options in speed and

functionality.

The processor upgrade kit contains a processor and thermal grease; you will need to re-use

the processor heat sink that came with your system.

4Information Update

www.dell.com | support.dell.com

Removing the Processor

CAUTION: Many repairs may only be done by a certified service technician. You should only perform

troubleshooting and simple repairs as authorized in your product documentation, or as directed by the

online or telephone service and support team. Damage due to servicing that is not authorized by Dell is

not covered by your warranty. Read and follow the safety instructions that came with the product.

Turn off the system, including any attached peripherals, and disconnect the system from

the electrical outlet.

Remove the bezel. See "Removing the Bezel" in "Troubleshooting Your System" in your

Installation and Troubleshooting Guide

Lay the system on its right side.

Remove the cover. See "Removing the Cover" in "Troubleshooting Your System" in your

Installation and Troubleshooting Guide

Remove the cooling shroud. See "Removing the Cooling Shroud" in "installing System

Components" in your

Installation and Troubleshooting Guide

NOTICE: After removing the heat sink, place it upside down on a flat surface to prevent the thermal

interface material from being damaged or contaminated.

Remove the heat sink. See Figure 1-1.

Open one securing clip by pressing the end of the clip down and away from the retention

until it clears the securing tab on the retention module, and then lift the clip up.

Repeat step a for the remaining securing clip.

Rotate the heat sink slightly and then lift the heat sink off the processor. Do not pry

the heat sink off the processor.

Information Update 5

Figure 1-1. Removing the Heat Sink

Press down on the processor socket release lever, then pull the release lever upward to the fully

open position. See Figure 1-2.

Open the processor cover. See Figure 1-2.

Lift the processor vertically out of the socket. Leave the processor cover and release lever in

the open position so that the socket is ready for the new processor. See Figure 1-2.

securing clips (2)

heat sink

6Information Update

www.dell.com | support.dell.com

Figure 1-2. Replacing the Processor

Installing a Processor

Unpack the new processor.

Ensure that the processor socket release lever is in the fully open position.

Align the pin 1 corners of the processor and socket. See Figure 1-2.

NOTICE: You must position the processor correctly in the socket to avoid damaging the processor and

the system board when you turn on the system. Be careful not to touch or bend the pins on the socket.

Set the processor lightly in the socket and ensure that the processor is level in the socket.

When the processor is positioned correctly, press it gently to seat it in the socket.

Close the processor cover.

Rotate the release lever back down until it snaps into place, securing the processor cover.

NOTICE: Do not operate the system without the heat sink installed. The heat sink is required to maintain

proper thermal conditions.

Using a clean lint-free cloth, remove the existing thermal grease from the heat sink that you

removed earlier in this procedure.

Apply thermal grease evenly to the top of the processor.

Lower the heat sink onto the processor. See Figure 1-1.

pin-1 locators (2)

processor cover

processor socket

processorsocket

release lever

processor

Information Update 7

Secure the heat sink to the retention module.

Gently press down on the heat sink and then press one securing clip to secure it.

Repeat step a for the remaining securing clip.

Ensure that the back fan connector is connected to the BACK_FAN connector on the system

board. See Figure A-3 in your

Installation and Troubleshooting Guide

Install the cooling shroud. See "Installing the Cooling Shroud" in "Installing System

Components" in your

Installation and Troubleshooting Guide

Install the cover. See "Replacing the Cover" in "Troubleshooting Your System" in your

Installation and Troubleshooting Guide

Stand the system upright.

Install the bezel. See "Installing the Bezel" in "Troubleshooting Your System" in your

Installation and Troubleshooting Guide

Reconnect the system to its electrical outlet and turn the system on, including any attached

peripherals.

Enter the System Setup program, and ensure that the processor options match the new

system configuration. See "Using the System Setup Program" in your

User's Guide

As the system boots, it detects the presence of the new processor and automatically changes

the system configuration information in the System Setup program. A message similar to the

following appears:

One 2.3 GHz Processor, Processor Bus: 533 MHz, L2 cache 256 KB

Confirm that the top line of the system data area in the System Setup program correctly

identifies the installed processor. See "Using the System Setup Program" in your

User's Guide

Exit the System Setup program.

Ensure that your system is running the latest BIOS version.

You can download the latest BIOS version from the Dell Support website located at

support.dell.com

Run the system diagnostics to verify that the new processor is operating correctly.

See "Running the System Diagnostics" in your

Installation and Troubleshooting Guide

for

information on running the diagnostics and troubleshooting any problems that may occur.

8Information Update

www.dell.com | support.dell.com

Andere Handbücher für PowerEdge 800

Inhaltsverzeichnis

Sprachen:

Andere Dell Server Handbücher

Dell

Dell PowerEdge R620 Bedienungsanleitung

Dell

Dell PowerEdge M420 Bedienungsanleitung

Dell

Dell PowerEdge R805 System Bedienungsanleitung

Dell

Dell EMC XC Core XC7525 Handbuch

Dell

Dell D560 Bedienungsanleitung

Dell

Dell Wyse ThinOS T10 Bedienungsanleitung

Dell

Dell PowerEdge R960 Handbuch

Dell

Dell PowerEdge 1500SC Bedienungsanleitung

Dell

Dell VTY3T Bedienungsanleitung

Dell

Dell PowerEdge SE400 Bedienungsanleitung

Dell

Dell Dimension 2400 Series Bedienungsanleitung

Dell

Dell EMC PowerEdge R650xs Handbuch

Dell

Dell PowerEdge R610 Bedienungsanleitung

Dell

Dell PowerEdge M1000e Bedienungsanleitung

Dell

Dell PowerEdge SC1435 Bedienungsanleitung

Dell

Dell PowerEdge R650XS M4JNT Handbuch

Dell

Dell PowerEdge R900 Bedienungsanleitung

Dell

Dell PowerEdge C5220 Bedienungsanleitung

Dell

Dell PowerEdge 1550 Bedienungsanleitung

Dell

Dell PowerEdge FX2 Kurzanleitung

Dell

Dell PowerEdge 2500 Bedienungsanleitung

Dell

Dell PowerEdge SC1435 Gebrauchsanweisung

Dell

Dell PowerEdge 6950 Bedienungsanleitung

Dell

Dell 8 Allgemeine Anweisungen

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Planet

Planet NAS-7410 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR635 V3 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY BX900 Bedienungsanleitung

Asus

Asus RS700DA-E6 PS4 Bedienungsanleitung

Vertiv

Vertiv Avocent ACS6000 Montage- und Wartungsanleitung

A & T Internationale

A & T Internationale Xserve Service-Handbuch