Dell PowerEdge 4200 Series Bedienungsanleitung

(Rev. 11/3/98) FILE LOCATION: S:\SYSTEMS\MARCONI\Rackingd\7U\05KCEa00\05kcebktp0.fm

www.dell.com

support.dell.com

Dell™ PowerEdge™ 6x00 and 4x00 Systems

RACK INSTALLATION GUIDE

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Computer Corporation is strictly forbidden.

Trademarks used in this text: Dell, the DELL E COM logo, RapidRails, and PowerEdge are trademarks of Dell Computer Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their

products. Dell Computer Corporation disclaims any proprietary interest in trademarks and trade names other than its own.

August 2000 P/N 05KCE Rev. A00

iii

Contents

Rack Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Recommended Tools and Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Installing the Rack Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Removing the Doors From the Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Removing the Doors From the Dell 42-U Rack . . . . . . . . . . . . . . . . . . . . . . . 4

Removing the Doors From the Dell 24-U Rack . . . . . . . . . . . . . . . . . . . . . . . 6

Installing the Slide Assemblies in the Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Installing the Shoulder Screws and the Rack Adapters . . . . . . . . . . . . . . . . . . .11

Installing the System in the Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Installing the Cable Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Installing the Cable-Management Arm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Reversing the Cable-Management Arm Installation. . . . . . . . . . . . . . . . . . . . . . 17

Replacing the Rack Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Replacing the Rack Doors on a 42-U Rack . . . . . . . . . . . . . . . . . . . . . . . . .18

Replacing the Rack Doors on a 24-U Rack . . . . . . . . . . . . . . . . . . . . . . . . .18

Index

Figures Figure 1. Rack Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Figure 2. Opening the 42-U Rack Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Figure 3. Removing the 42-U Rack Doors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Figure 4. Opening the 24-U Rack Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Figure 5. Removing the 24-U Rack Doors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Figure 6. One Rack Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Figure 7. Marking the Vertical Rails . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Figure 8. Installing the Slide Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Figure 9. Installing the Rack Adapter and Shoulder Screws . . . . . . . . . . . . . . . .12

Figure 10. Installing the Computer in the Rack. . . . . . . . . . . . . . . . . . . . . . . . . . .13

Figure 11. Installing the Cable Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Figure 12. Installing the Cable-Management Arm . . . . . . . . . . . . . . . . . . . . . . . . 15

Figure 13. Reversing the Cable-Management Arm . . . . . . . . . . . . . . . . . . . . . . . 17

FILE LOCATION: S:\SYSTEMS\MARCONI\Rackingd\7U\05KCEa00\05KCEsi0.fm

DELL CONFIDENTIAL - Preliminary 9/8/00

Safety Instructions

Use the following safety guidelines to ensure your own personal safety and to help

protect your server, storage system, or appliance from potential damage.

Notes, Notices, Cautions, and Warnings

Throughout this guide, blocks of text may be accompanied by an icon and printed in

bold type or in italic type. These blocks are notes, notices, cautions, and warnings,

and they are used as follows:

NOTE: A NOTE indicates important information that helps you make better use of

your computer system.

NOTICE: A NOTICE indicates either potential damage to hardware or loss

of data and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potentially hazardous situation which, if

not avoided, may result in minor or moderate injury.

WARNING: A WARNING indicates a potentially hazardous situation which,

if not avoided, could result in death or serious bodily injury.

Safety Caution and Warnings

Observe the following caution and warnings while servicing this system:

CAUTION: There is a danger of a new battery exploding if it is incorrectly

installed. Replace the battery only with the same or equivalent type recom-

mended by the manufacturer. Discard used batteries according to the

manufacturer’s instructions.

WARNING: The power supplies in your computer or storage system may

produce high voltages and energy hazards, which can cause bodily harm.

Only trained service technicians are authorized to remove the computer

covers and access any of the components inside the computer. This warning

applies to Dell PowerEdge 4xxx or higher servers, Dell PowerVault 2xxS

storage systems, and Dell PowerApp appliances.

DELL CONFIDENTIAL - Preliminary 9/8/00

FILE LOCATION: S:\SYSTEMS\MARCONI\Rackingd\7U\05KCEa00\05KCEsi0.fm

WARNING: This system may have more than one power supply cable. To

reduce the risk of electrical shock, a trained service technician must discon-

nect all power supply cables before servicing the system.

DÙLEITÉ UPOZORNÌNÍ: Tento systém mùe mít více napájecích kabelù. Ke

sníení rizika úrazu elektrickým proudem je nutné, aby školený servisní technik

pøed provádìním servisu systému odpojil všechny napájecí kabely.

ADVARSEL: Dette system kan have mere end et strømforsyningskabel. For

at reducere risikoen for elektrisk stød, bør en professionel servicetekniker

frakoble alle strømforsyningskabler, før systemet serviceres.

VAROITUS: Tässä järjestelmässä voi olla useampi kuin yksi virtajohto. Säh-

köiskuvaaran pienentämiseksi ammattitaitoisen huoltohenkilön on

irrotettava kaikki virtajohdot ennen järjestelmän huoltamista.

ÏÐÅÄÓÏÐÅÆÄÅÍÈÅ: Äàííàÿ ñèñòåìà ìîæåò èìåòü íåñêîëüêî êàáåëåé

ýëåêòðîïèòàíèÿ. Âî èçáåæàíèå ýëåêòðè÷åñêîãî óäàðà êâàëèôèöèðîâàííûé

òåõíèê äîëæåí îòêëþ÷èòü âñå êàáåëè ýëåêòðîïèòàíèÿ ïðåæäå, ÷åì ïðèñòóïèòü ê

îáñëóæèâàíèþ ñèñòåìû.

OSTRZE¯ENIE: System ten mo¿e mieæ wiêcej ni¿ jeden kabel zasilania. Aby

zmniejszyæ ryzyko pora¿enia pr¹dem, przed napraw¹ lub konserwacj¹ systemu

wszystkie kable zasilania powinny byæ od³¹czone przez przeszkolonego technika

obs³ugi.

ADVARSEL! Det er mulig at dette systemet har mer enn én strømledning.

Unngå fare for støt: En erfaren servicetekniker må koble fra alle strømled-

ninger før det utføres service på systemet.

VARNING: Detta system kan ha flera nätkablar. En behörig servicetekniker

måste koppla loss alla nätkablar innan service utförs för att minska risken

för elektriska stötar.

Additional Safety Precautions

To reduce the risk of bodily injury, electrical shock, fire, and damage to the equipment,

observe the following precautions.

General Precautions

Observe the following general precautions for using and working with your system:

•Observe and follow service markings. Do not service any Dell product except as

explained in your Dell system documentation. Opening or removing covers that

are marked with the triangular symbol with a lightning bolt may expose you to

electrical shock. Components inside these compartments should be serviced

only by a Dell authorized service technician.

DELL CONFIDENTIAL - Preliminary 9/8/00

FILE LOCATION: S:\SYSTEMS\MARCONI\Rackingd\7U\05KCEa00\05KCEsi0.fm

•If any of the following conditions occur, unplug the product from the electrical

outlet and replace the part or contact your Dell authorized service provider:

— The power cable, extension cable, or plug is damaged.

— An object has fallen into the product.

— The product has been exposed to water.

— The product has been dropped or damaged.

— The product does not operate correctly when you follow the operating

instructions.

•Keep your system components away from radiators and heat sources. Also, do

not block cooling vents.

•Do not spill food or liquids on your system components, and never operate the

product in a wet environment. If the computer gets wet, see the appropriate

chapter in your troubleshooting guide or contact a Dell-authorized service

provider.

•Do not push any objects into the openings of your system components. Doing so

can cause fire or electric shock by shorting out interior components.

•Use the product only with Dell products or other Dell-approved equipment.

•Allow the product to cool before removing covers or touching internal

components.

•Use the correct external power source. Operate the product only from the type

of power source indicated on the electrical ratings label. If you are not sure of the

type of power source required, consult your Dell service provider or local power

company.

•To help avoid damaging your system components, be sure the voltage selection

switch (if provided) on the power supply is set to match the power available at

your location:

— 115 volts (V)/60 hertz (Hz) in most of North and South America and some Far

Eastern countries such as South Korea and Taiwan

— 100 V/50 Hz in eastern Japan and 100 V/60 Hz in western Japan

— 230 V/50 Hz in most of Europe, the Middle East, and the Far East

Also be sure that your monitor and attached devices are electrically rated to oper-

ate with the power available in your location.

•Use only approved power cable(s). If you have not been provided with a power

cable for your server, storage system, or appliance, or for any AC-powered option

intended for your system, purchase a power cable that is approved for use in your

country. The power cable must be rated for the product and for the voltage and

current marked on the product’s electrical ratings label. The voltage and current

rating of the cable should be greater than the ratings marked on the product.

xii

DELL CONFIDENTIAL - Preliminary 9/8/00

FILE LOCATION: S:\SYSTEMS\MARCONI\Rackingd\7U\05KCEa00\05KCEsi0.fm

•To help prevent electric shock, plug the system/components and peripheral

power cables into properly grounded electrical outlets. These cables are

equipped with three-prong plugs to help ensure proper grounding. Do not use

adapter plugs or remove the grounding prong from a cable. If you must use an

extension cable, use a three-wire cable with properly grounded plugs.

•Observe extension cable and power strip ratings. Make sure that the total

ampere rating of all products plugged into the extension cable or power strip

does not exceed 80 percent of the extension cable or power strip ampere ratings

limit.

•To help protect your system/components from sudden, transient increases and

decreases in electrical power, use a surge suppressor, line conditioner, or un-

interruptible power supply (UPS).

•Position system cables and power cables carefully; route system cables and the

power cable and plug so that they cannot be stepped on or tripped over. Be sure

that nothing rests on your system components’ cables or power cable.

•Do not modify power cables or plugs. Consult a licensed electrician or your

power company for site modifications. Always follow your local/national wiring

rules.

•To help avoid possible damage to the system board, wait 5 seconds after turning

off the system before removing a component from the system board or discon-

necting a peripheral device from the computer.

•Handle batteries carefully. Do not disassemble, crush, puncture, short external

contacts, dispose of in fire or water, or expose batteries to temperatures higher

than 60 degrees Celsius (140 degrees Fahrenheit). Do not attempt to open or ser-

vice batteries; replace batteries only with batteries designated for the product.

•Turn down the volume before using headphones or other audio devices.

Precautions for Servers, Storage Systems, and Appliances

Observe the following additional safety guidelines for your system:

•Unless your installation and/or troubleshooting documentation specifically allows

it, do not remove enclosure covers, attempt to override the safety interlocks, or

access any components inside the system. Depending on your system, installa-

tion and repairs may be done only by individuals who are qualified to service your

computer or storage system equipment and trained to deal with products capa-

ble of producing hazardous energy levels.

•When connecting or disconnecting power to hot-pluggable power supplies, if

offered with your Dell product, observe the following guidelines:

— Install the power supply before connecting the power cable to the power

supply.

— Unplug the power cable before removing the power supply.

— If the system has multiple sources of power, disconnect power from the sys-

tem by unplugging all power cables from the power supplies.

xiii

DELL CONFIDENTIAL - Preliminary 9/8/00

FILE LOCATION: S:\SYSTEMS\MARCONI\Rackingd\7U\05KCEa00\05KCEsi0.fm

•Move products with care; ensure that all casters and/or stabilizers are firmly con-

nected to the computer or storage system. Avoid sudden stops and uneven

surfaces.

Precautions for Rack-Mountable Products

Observe the following precautions for rack stability and safety. Also refer to the rack

installation documentation accompanying the system and the rack for specific warn-

ing and/or caution statements and procedures.

Servers, storage systems, and appliances are considered to be components in a rack.

Thus, “component” refers to any server, storage system, or appliance, as well as to

various peripherals or supporting hardware.

WARNING: Installing Dell system components in a Dell rack without the

front and side stabilizers installed could cause the rack to tip over, poten-

tially resulting in bodily injury under certain circumstances. Therefore,

always install the stabilizers before installing components in the rack.

After installing system/components in a rack, never pull more than one

component out of the rack on its slide assemblies at one time. The weight

of more than one extended component could cause the rack to tip over and

injure someone.

NOTE: Dell’s servers, storage systems, and appliances are certified as components

for use in Dell’s rack cabinet using the Dell customer rack kit. The final installation of

Dell systems and rack kits in any other brand of rack cabinet has not been approved by

any safety agencies. It is the customer’s responsibility to have the final combination of

Dell systems and rack kits for use in other brands of rack cabinets evaluated for suit-

ability by a certified safety agency.

•System rack kits are intended to be installed in a Dell rack by trained service tech-

nicians. If you install the kit in any other rack, be sure that the rack meets the

specifications of a Dell rack.

•Do not move large racks by yourself. Due to the height and weight of the rack,

Dell recommends a minimum of two people to accomplish this task.

•Before working on the rack, make sure that the stabilizers are secure to the rack,

extend to the floor, and that the full weight of the rack rests on the floor. Install

front and side stabilizers on a single rack or front stabilizers for joined multiple

racks before working on the rack.

•Always load the rack from the bottom up, and load the heaviest item in the rack

first.

•Make sure that the rack is level and stable before extending a component from

the rack.

•Use caution when pressing the component rail release latches and sliding a com-

ponent into or out of a rack; the slide rails can pinch your fingers.

•After a component is inserted into the rack, carefully extend the rail into a locking

position, and then slide the component into the rack.

xiv

DELL CONFIDENTIAL - Preliminary 9/8/00

FILE LOCATION: S:\SYSTEMS\MARCONI\Rackingd\7U\05KCEa00\05KCEsi0.fm

•Do not overload the AC supply branch circuit that provides power to the rack. The

total rack load should not exceed 80 percent of the branch circuit rating.

•Ensure that proper airflow is provided to components in the rack.

•Do not step on or stand on any system/component when servicing other sys-

tems/components in a rack.

Precautions for Products With Modems,

Telecommunications, or Local Area Network Options

Observe the following guidelines when working with options:

•Do not connect or use a modem or telephone during a lightning storm. There

may be a risk of electrical shock from lightning.

•Never connect or use a modem or telephone in a wet environment.

•Do not plug a modem or telephone cable into the network interface controller

(NIC) receptacle.

•Disconnect the modem cable before opening a product enclosure, touching or

installing internal components, or touching an uninsulated modem cable or jack.

•Do not use a telephone line to report a gas leak while you are in the vicinity of the

leak.

Precautions for Products With Laser Devices

Observe the following precautions for laser devices:

•Do not open any panels, operate controls, make adjustments, or perform proce-

dures on a laser device other than those specified in the product’s

documentation.

•Only authorized service technicians should repair laser devices.

When Working Inside Your Computer

Before you remove the computer covers, perform the following steps in the sequence

indicated.

CAUTION: Some Dell systems can be serviced only by trained service tech-

nicians because of high voltages and energy hazards. Do not attempt to

service the computer system yourself, except as explained in this guide and

elsewhere in Dell documentation. Always follow installation and service

instructions closely.

NOTICE: To help avoid possible damage to the system board, wait 5 sec-

onds after turning off the system before removing a component from the

system board or disconnecting a peripheral device from the computer.

Andere Handbücher für PowerEdge 4200 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Dell Server Handbücher

Dell

Dell EMC VxFlex Ready Node 14G Handbuch

Dell

Dell PowerEdge C6320 Bedienungsanleitung

Dell

Dell PowerEdge C5230 Bedienungsanleitung

Dell

Dell OptiPlex FX130 Bedienungsanleitung

Dell

Dell EMC PowerEdge C6420 Handbuch

Dell

Dell PowerEdge R820 Kurzanleitung

Dell

Dell 810 Bedienungsanleitung

Dell

Dell PowerEdge C6220 II Bedienungsanleitung

Dell

Dell PowerEdge R960 Handbuch

Dell

Dell PowerEdge 2850 Bedienungsanleitung

Dell

Dell PowerEdge 2500 Leitfaden

Dell

Dell POWEREDGE CLUSTER SE100 Montageanleitung

Dell

Dell 8 Technisches Handbuch

Dell

Dell XC6320 Bedienungsanleitung

Dell

Dell PowerEdge FM120x4 Bedienungsanleitung

Dell

Dell Force10 S25-01-GE-24P Bedienungsanleitung

Dell

Dell External OEMR R620 Bedienungsanleitung

Dell

Dell PowerEdge 4600 Bedienungsanleitung

Dell

Dell DR4000 Restore Manager Bedienungsanleitung

Dell

Dell PowerEdge 1955 Bedienungsanleitung

Dell

Dell POWEREDGE DL385 Bedienungsanleitung

Dell

Dell EMC PowerEdge R640 Handbuch

Dell

Dell DL4300 Bedienungsanleitung

Dell

Dell PowerEdge 1655MC Technisches Handbuch

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Planet

Planet NAS-7410 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR635 V3 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY BX900 Bedienungsanleitung

Asus

Asus RS700DA-E6 PS4 Bedienungsanleitung

Vertiv

Vertiv Avocent ACS6000 Montage- und Wartungsanleitung

A & T Internationale

A & T Internationale Xserve Service-Handbuch