Dell POWEREDGE 4300 Bedienungsanleitung



™











Throughout this guide, blocks of text may be accompanied by an icon and printed in

bold type or in italic type. These blocks are notes, cautions, and warnings, and they

are used as follows:

NOTE: A NOTE indicates important information that helps you make better use of

your computer system.





!" !"



Some warnings may appear in alternate formats and may be unaccompanied by an

icon. In such cases, the specific presentation of the warning is mandated by regula-

tory authority.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Computer Cor-

poration is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, and PowerEdge are trademarks of Dell

Computer Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities

claiming the marks and names or their products. Dell Computer Corporation disclaims any pro-

prietary interest in trademarks and trade names other than its own.

November 1998 P/N 2294D Rev. A02

SMB Connector and SCSI Cable Strain-Relief Kit Installation Instructions 1











NOTE: If you purchased your PowerEdge server and PowerEdge Scalable Disk System

100 (SDS 100) storage system at the same time, the SMB connector is preinstalled in

your system and you can skip to the section entitled “Installing the SCSI Cable Strain-

Relief Clip or Bracket.”

Before connecting a Dell PowerEdge 6300 or 4300 system to a Dell PowerEdge

SDS 100 storage system, you must install an internal server management bus (SMB)

connector and cable. The cable runs from the system board to the SMB connector on

the back panel to provide a connection point for the external SMB cable from the

SDS 100.

The kit for the internal SMB cable consists of the internal SMB cable and a bracket-

mounted SMB connector for installation on the back panel of the system. Depending

on the SMB installation kit you receive, the SMB connector is mounted on either a

filler bracket for installation in the PCI1 slot or on a bracket that mounts in the general

signal out (GSO) slot.

NOTE: You can use the GSO-mounted SMB connector only if the support panel that

covers the microprocessor compartment inside your system chassis supports installa-

tion of the GSO-mounted SMB connector. You have the proper support panel if your

panel has a cutout that allows the SMB connector to extend through it (see Figure 5).

To install the SMB connector and internal cable, perform the following steps:

1. Read and follow the precautions in “Safety First—For You and Your Computer” in

Chapter 7 of the Installation and Troubleshooting Guide for your system.

2. Remove the computer cover and the interior support panel as described in

Chapter 7 of your Installation and Troubleshooting Guide.

2 SMB Connector and SCSI Cable Strain-Relief Kit Installation Instructions

3. If your system supports the GSO-slot bracket, perform steps 4 and 5; otherwise,

go to step 6 for instructions on installing the PCI-slot bracket.

4. For GSO-slot brackets, locate the GSO slot on the system’s back panel (at the

upper right-hand side as viewed from the back) and remove the tab for the slot.

5. From inside the chassis, orient the SMB connector as shown in Figure 1 (for

6300 systems) or Figure 2 (for 4300 systems) and insert it into the tab opening. On

the back panel, secure the SMB connector with the screws that came in the kit.

NOTE: Be sure not to over-tighten the screws.



 !"

SMB

connector

system

board

SMB connector

(SDS_SMB)

SMB cable

GSO slot

SMB Connector and SCSI Cable Strain-Relief Kit Installation Instructions 3

#

$ !"

6. Locate the PCI1 slot on the system’s back panel and remove the filler bracket

from the slot.

Refer to Chapter 8 of your system’s Installation and Troubleshooting Guide for

instructions on releasing the expansion card clip that secures the filler bracket.

7. Insert the SMB connector bracket into the PCI1 back-panel slot as shown in

Figure 3 (for PowerEdge 6300 systems) or Figure 4 (for PowerEdge 4300 sys-

tems), and latch the expansion-card clip to secure the bracket.

SMB

connector

system

board

SMB connector

(SDS_SMB)

SMB cable

GSO slot

4 SMB Connector and SCSI Cable Strain-Relief Kit Installation Instructions



 !"

$

$ !"

8. Connect the SMB cable to the SMB connector on the bracket and seat the other

end in the SDS_SMB connector on the system board.

The SMB connector is located near the keyboard and mouse connectors on the

6300 system and between the dual in-line memory module (DIMM) sockets and

the video connector on the 4300 system.

SMB connector

system

board

SMB connector

(SDS_SMB)

internal SMB

cable

PCI1 back-panel slot

SMB connector

system

board

SMB connector

(SDS_SMB)

internal SMB

cable

PCI1 back-panel slot

SMB Connector and SCSI Cable Strain-Relief Kit Installation Instructions 5

9. Reinstall the support panel.

If you installed the GSO-slot SMB connector, route the connector and cable

through the cutout in the support panel (see Figure 5). Ensure that the connector

and cable are positioned properly so that they do not bind between the rubber

standoffs.

%&'((

10. Replace the computer cover.

You are now ready to connect the external SMB cable from the SDS 100 storage sys-

tem. For more information on connecting the storage system to a host computer, see

Chapter 2 of the Dell PowerEdge SDS 100 Storage System Installation and Service

Guide.

thumbscrews (2)

support panel

SMB

connector

support panel

cutout

6 SMB Connector and SCSI Cable Strain-Relief Kit Installation Instructions

 !"#$

%

DellPowerEdge 6300 and 4300 computer systems equipped with a Dell PowerEdge

SDS 100 storage system include two strain-relief clips or one strain-relief bracket in

the cable kit. When installed, the bracket or clips prevent deflection of the SCSI

cables connected to the host adapter card in the system. Deflection of the SCSI inter-

face cables can damage the SCSI host adapter card.

The following items are included in the cable strain-relief kit:

Two long or two short SCSI cables

Two plastic cable strain-relief clips with adhesive backs or one strain-relief bracket

Two alcohol wipes



If your kit includes SCSI strain-relief clips, perform the following steps to install the

clips:

1. Locate the flat area on the computer’s back panel to the right of the redundant

arrays of independent disks (RAID) controller card connectors.

The flat area is located between the chassis ventilation holes and the edge of the

computer cover.

NOTE: Do not affix the cable strain-relief clips over the chassis ventilation holes or

on the edge of the computer cover.

2. Use the alcohol wipes to thoroughly clean the area on the back panel.

3. Peel the plastic liner from the back of the cable strain-relief clip to expose the

adhesive tape.

4. Orient the plastic clip so that the flat tab is on the top and the grooved tab is on

the bottom (see Figure 6).

SMB Connector and SCSI Cable Strain-Relief Kit Installation Instructions 7

)&*(

5. Press the back of the clip firmly against the computer’s back panel.

6. Affix the second clip above or below the other clip.

Allow 24 hours for the clips to set before attaching the cables.

7. Turn off the computer.

8. Pull down the grooved tab and insert the cable into the clip.

9. Push the grooved tab under the flat tab until the clip locks securely in place.

10. Repeat steps 8 and 9 for the second cable.

11. Turn on the computer.



If your kit includes a SCSI strain-relief bracket, perform the following steps to install

the bracket:

1. Connect the SCSI interface cable(s) to the SCSI host adapter card.

Secure the cable(s) using the two thumbscrews on the cable connector(s).

flat tab grooved tab

8 SMB Connector and SCSI Cable Strain-Relief Kit Installation Instructions

2. Insert the tabs on the end of the bracket cradle into the bracket slots adjacent to

the SCSI host adapter card as shown in Figure 7.

Secure the bracket cradle to the chassis with a Phillips-head screw.

+)&*,

bracket cradle

back of computer

bracket slots

Phillips-head

screw

tabs

SCSI host adapter

SCSI cable

Andere Handbücher für POWEREDGE 4300

Dieses Handbuch passt für folgende Modelle

Andere Dell Server Handbücher

Dell

Dell VTY3T Bedienungsanleitung

Dell

Dell Wyse 3030 LT Bedienungsanleitung

Dell

Dell PowerEdge 2950 Bedienungsanleitung

Dell

Dell PowerEdge 1650 Technisches Handbuch

Dell

Dell PowerEdge R930 Bedienungsanleitung

Dell

Dell PowerEdge R810 Bedienungsanleitung

Dell

Dell PowerEdge C1100 Technisches Handbuch

Dell

Dell PowerEdge SC420 Stücklistenhandbuch

Dell

Dell PowerEdge R830 Bedienungsanleitung

Dell

Dell PowerEdge C8000 Bedienungsanleitung

Dell

Dell PowerEdge C6105 Kurzanleitung

Dell

Dell PowerEdge 850 Leitfaden

Dell

Dell PowerEdge 2500 Bedienungsanleitung

Dell

Dell S5000 Series Bedienungsanleitung

Dell

Dell PowerEdge 2420 Bedienungsanleitung

Dell

Dell PowerEdge T610 Bedienungsanleitung

Dell

Dell PowerEdge XR7620 Handbuch

Dell

Dell PowerVault MD3600i Series Bedienungsanleitung

Dell

Dell PowerEdge C5220 Handbuch

Dell

Dell PowerEdge R300 Bedienungsanleitung

Dell

Dell PowerApp .cache 100 Technisches Handbuch

Dell

Dell PowerEdge 2950 Technisches Handbuch

Dell

Dell Force10 MXL Blade Bedienungsanleitung

Dell

Dell PowerEdge C4130 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Planet

Planet NAS-7410 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR635 V3 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY BX900 Bedienungsanleitung

Asus

Asus RS700DA-E6 PS4 Bedienungsanleitung