Dell Poweredge metered Bedienungsanleitung

Cable Routing Procedures for

Dell™ PowerEdge™ T610 Systems

A Dell™Technical White Paper

Dell™│Datacenter Infrastructure Engineering

By Chris Kitten and Jose L. Flores

March 2011

Cable Routing Procedures for Dell™ PowerEdge™ T610 Systems

Page ii

THIS WHITE PAPER IS FOR INFORMATIONAL PURPOSES ONLY, AND MAY CONTAIN TYPOGRAPHICAL

ERRORS AND TECHNICAL INACCURACIES. THE CONTENT IS PROVIDED AS IS, WITHOUT EXPRESS

OR IMPLIED WARRANTIES OF ANY KIND.

the express written permission of Dell Inc. is strictly forbidden. For more information, contact Dell.

Dell

, the

DELL

logo, the

DELL

badge, and

PowerEdge

are trademarks of Dell Inc.

Cable Routing Procedures for Dell™ PowerEdge™ T610 Systems

Page 1

Contents

Introduction...............................................................................................................................................................2

Section 1: Cabling a Dell™ PowerEdge™ T610 With a Cable Management Arm (CMA) ............................................2

1.1 Connecting the CMA Cables to the System..................................................................................................2

1.2 Routing the Power Cables Through the Strain Reliefs .................................................................................3

1.3 Installation of the CMA ................................................................................................................................3

Section 2: Cabling a Dell™ PowerEdge™ T610 System Without a CMA.....................................................................5

2.1 Routing the Cables .......................................................................................................................................5

Section 3: Replacing a Power Supply on a PowerEdge™ T610 System With a CMA..................................................6

Table of Figures

Figure 1: System with Cables Installed .................................................................................................................. 2

Figure 2: Routing Power Cables Through the Strain Reliefs ............................................................................. 3

Figure 3: Routing the Cables Through the CMA ................................................................................................. 4

Figure 4: Right-Side Mounted CMA Installation .................................................................................................. 4

Figure 5: Left-Side Mounted CMA Installation..................................................................................................... 5

Figure 6: Cable Routing Without a CMA............................................................................................................... 5

Figure 7: Replacing the Power Supply................................................................................................................... 6

Cable Routing Procedures for Dell™ PowerEdge™ T610 Systems

Page 2

Introduction

This white paper covers recommended cable routing procedures for Dell™ PowerEdge™ T610

systems in the following racks:

PowerEdge™ 2410

PowerEdge™ 4210

PowerEdge™ 2420

PowerEdge™ 4220 (including wide and deep versions)

PowerEdge™ 4820 (including wide and deep versions)

If you are using the optional CMA, following these procedures will allow you to extend the system

from the rack for service without powering down or disconnecting the cables. If you are not using the

CMA, following these procedures will ensure secure attachment and strain relief of the cables behind

the system. For guidelines on how to route cables within the rack, refer to the Dell

Best Practices

Guide for Rack Enclosures

white paper.

Section 1: Cabling a Dell™ PowerEdge™ T610 With a Cable Management

Arm (CMA)

This section details how to cable a PowerEdge™ T610 system using a CMA. If you are cabling the

system without the optional CMA, refer to Section 2.

Follow the instructions contained in the

Rack Installation Guide

in the rail kit to install the server into

the rack. Once installed, use these instructions to install the cables. All illustrations in the following

sections were created using a PowerEdge™ T610 system.

NOTE: PowerEdge™ T610 systems are compatible with the PowerEdge™ T710 rails and CMAs.

1.1

Connecting the CMA Cables to the System

Attach the CMA tray to the back of the rails as described in the

CMA Installation Instructions

provided

in the CMA kit. Connect all applicable cables to the rear of the system and verify that all connections

are secure. See Figure 1.

Figure 1: System with Cables Installed

Cable Routing Procedures for Dell™ PowerEdge™ T610 Systems

Page 3

1.2

Routing the Power Cables Through the Strain Reliefs

After you have installed the tray and cables, route the power cables through the strain reliefs located

on the power supply handles as shown in Figure 2.

Figure 2: Routing Power Cables Through the Strain Reliefs

1.3

Installation of the CMA

The CMA can be installed on either the rear right or rear left side of the rails. Mounting the CMA on the

side that is opposite of the power supplies (right-side mount) is recommended; otherwise, the CMA

must be partially disconnected in order to remove the lower power supply. Refer to Section 3 for

details on power supply replacement.

NOTE: For guidelines on how to route cables within the rack, refer to the Dell

Best Practices Guide for

Rack Enclosures

white paper

NOTE: If you are installing fiber-optic cables in the CMA, a cable bend radius of at least 1 inch must be

maintained throughout the length of the cable

It is recommended that fiber-optic cables be routed

on the exterior of the cable bundle to increase the bend radius of the fiber-optic cables through the

CMA. Additionally, a large amount of slack at the entrance and exit of the CMA is recommended.

1. Install the CMA on either the rear right or rear left side of the rails by attaching both CMA housings

to the attachment brackets on the rails.

2. Route the cables through the CMA while avoiding twisting the cables. Use the hook and loop

straps on the CMA to secure the cables. See Figure 3.

3. If the cable bundle includes a keyboard, video, and mouse (KVM) dongle, place the dongle inside

the CMA basket.

4. Once you have routed all the cables through the CMA, dress the cable slack between the back of

the system and the entrance of the CMA using the tie wraps (shown in yellow in all illustrations)

provided in the CMA kit.

Cable Routing Procedures for Dell™ PowerEdge™ T610 Systems

Page 4

5. Clip off the excess length of material from the tie wraps. Make sure that the heads of the tie wraps

are positioned so as to avoid interference with adjacent systems. Return the CMA to the closed

(retracted) position.

6. Extend the system out of the rack to verify that there is sufficient slack in the cables on both ends

of the CMA.

See Figure 4 for an example of a completed right-side mounted CMA installation.

See Figure 5 for an example of a completed left-side mounted CMA installation.

Figure 3: Routing the Cables Through the CMA

Figure 4: Right-Side Mounted CMA Installation (Preferred)

Cables entering the CMA should have

a small amount of slack to avoid cable

strain when the CMA is extended.

NOTE: Do not store excess cable

slack inside the CMA. The cable may

protrude through the CMA, thus

causing binding and potentially

damaging the cable.

KVM dongle placed inside the basket.

Cable Routing Procedures for Dell™ PowerEdge™ T610 Systems

Page 5

Figure 5: Left-Side Mounted CMA Installation

Section 2: Cabling a Dell™ PowerEdge™ T610 System Without a CMA

NOTE: The CMA on Dell™ PowerEdge™ T610 systems is optional. Without the CMA installed, the

system must be powered down and all cables disconnected before it can be removed from the rack.

2.1

Routing the Cables

1. Connect all applicable cables to the rear of the system and verify that all connections are secure.

2. Using the hook and loop straps supplied with the rail kit, bundle the cables and secure them to

either the left or right CMA attachment brackets as described in the

Rack Installation Instructions

See Figure 6 for an example of data cables secured to the left CMA bracket and power cables

secured to the right CMA bracket.

3. It is recommended that the cables be secured to the outer brackets, but cables may be secured to

the inner brackets as well if desired.

Figure 6: Cable Routing Without a CMA

Cable Routing Procedures for Dell™ PowerEdge™ T610 Systems

Page 6

Section 3: Replacing a Power Supply on a PowerEdge™ T610 System With a

CMA

NOTE: The steps described below apply to the bottom power supply only when the CMA is installed

to the left side. If the CMA is attached to the right side, both power supplies can be removed without

removal of the CMA. If the CMA is attached to the left side, the top power supply can be replaced with

the CMA in its closed (retracted) position.

1. Swing the CMA to its service position.

2. Disengage the strain relief and disconnect the power cord from the power supply.

3. Disconnect the inner CMA attachment housing from the rail as shown in Figure 8.

4. While supporting the CMA with one hand, remove and replace the power supply with the

other hand as shown in Figure 8.

5. Reconnect the CMA attachment housing to the rail.

6. Plug in the power cord, re-engage the strain relief, and return the CMA to the closed

(retracted) position.

Figure 7: Replacing the Power Supply

Inner CMA attachment housing

has been disconnected.

Andere Handbücher für Poweredge metered

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Dell Server Handbücher

Dell

Dell PowerEdge 860 Bedienungsanleitung

Dell

Dell PowerEdge 1655MC Handbuch

Dell

Dell PowerEdge R510 Bedienungsanleitung

Dell

Dell PowerEdge 2410 Bedienungsanleitung

Dell

Dell PS4100 Montageanleitung

Dell

Dell Wyse ThinOS T10 Bedienungsanleitung

Dell

Dell PowerEdge C6220 II Bedienungsanleitung

Dell

Dell PowerEdge R930 Bedienungsanleitung

Dell

Dell PowerEdge R630 Bedienungsanleitung

Dell

Dell PowerEdge R420 Betriebsanleitung

Dell

Dell PowerEdge R510 Technisches Handbuch

Dell

Dell PowerEdge R510 Bedienungsanleitung

Dell

Dell PowerEdge UPS 500T Bedienungsanleitung

Dell

Dell PowerEdge T110 Bedienungsanleitung

Dell

Dell PowerEdge PDU Managed LED Bedienungsanleitung

Dell

Dell DX6000 Bedienungsanleitung

Dell

Dell Wyse C10LE Service-Handbuch

Dell

Dell PowerVault 735N Stücklistenhandbuch

Dell

Dell PowerEdge 1800 Technisches Handbuch

Dell

Dell PowerConnect W-AirWave 7.6 Bedienungsanleitung

Dell

Dell EMC VxRail S Series Bedienungsanleitung

Dell

Dell PowerEdge C6220 Bedienungsanleitung

Dell

Dell PowerEdge R430 Bedienungsanleitung

Dell

Dell PowerEdge R830 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Planet

Planet NAS-7410 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR635 V3 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY BX900 Bedienungsanleitung

Asus

Asus RS700DA-E6 PS4 Bedienungsanleitung