Dell PowerEdge PDU Managed LED Bedienungsanleitung

Greg Henderson and Jose L. Flores

Data Center Infrastructure Engineering

May 2012

Cable Routing Procedures for the

Dell™ PowerEdge™ R520 System

This Dell Technical White Paper explains the best practices for routing

and securing the cables exiting the back of the R520 system.

Cable Routing Procedures for the Dell PowerEdge R520 System

This document is for informational purposes only and may contain typographical errors and

technical inaccuracies. The content is provided as is, without express or implied warranties of any

kind.

in typography or photography. Dell, the Dell logo, and PowerEdge are trademarks of Dell Inc. Other

trademarks and trade names may be used in this document to refer to either the entities claiming the

marks and names or their products. Dell disclaims proprietary interest in the marks and names of

others.

May 2012| Rev 1.0

Cable Routing Procedures for the Dell PowerEdge R520 System

Contents

Introduction .............................................................................................................4

Section 1: Cabling a PowerEdge R520 system with a CMA.......................................................4

1.1. Connecting the cables to the system...................................................................4

1.2. Routing the power cables through the strain reliefs.................................................5

1.3. Installing the CMA..........................................................................................5

Section 2: Replacing a hot swap power supply on a PowerEdge R520 system with a CMA ...............8

2.1. Replacing a hot swap power supply with a left-side mounted CMA...............................8

2.2. Replacing a hot swap power supply with a right-side mounted CMA .............................8

Section 3: Cabling a PowerEdge R520 system on sliding rails without a CMA............................. 10

3.1. Routing the cables ....................................................................................... 10

3.2. Removing the outer CMA brackets for shallow racks .............................................. 10

Section 4: Cabling a PowerEdge R520 system installed on static rails ..................................... 11

Figures

Figure 1. System with cables installed.............................................................................4

Figure 2. Routing power cables through the strain reliefs on hot swap power supplies ..................5

Figure 3. Routing the power cable through the strain relief on a fixed power supply ....................5

Figure 4. Attaching the inner CMA attachment bracket ........................................................6

Figure 5. Routing the cables through the CMA....................................................................6

Figure 6. Left-side mounted CMA installation (preferred)......................................................7

Figure 7. Right-side mounted CMA installation (CMA shown in service position)...........................7

Figure 8. Disconnecting the CMA attachment housings .........................................................9

Figure 9. Replacing a hot swap power supply.....................................................................9

Figure 10. Cable routing on sliding rails without a CMA........................................................ 10

Figure 11. Removing the outer CMA brackets for shallow racks .............................................. 11

Figure 12. Cabling a system installed in static rails............................................................. 11

Cable Routing Procedures for the Dell PowerEdge R520 System

Introduction

This white paper covers recommended cable routing procedures for the Dell™ PowerEdge™ R520 system

in the following racks:

•PowerEdge 2410, 4210

•PowerEdge 2420, 4220, 4820 (including wide and deep versions)

•PowerEdge Energy Smart 4020S, 4620S

If you are using the optional cable management arm (CMA), following these procedures will allow you

to extend the system from the rack for service without powering down or disconnecting the cables. If

you are not using the CMA, following these procedures will ensure secure attachment and strain relief

of the cables behind the system.

For guidelines on how to route cables within the rack, refer to the Dell Best Practices Guide for Rack

Enclosure white paper. For additional details regarding potential interferences between the CMA and

rear-mount power distribution units (PDUs) in Dell racks as well as general information about third

party rack compatibility, refer to the Dell Enterprise Systems Rail Sizing and Rack Compatibility Matrix

located at http://content.dell.com/us/en/enterprise/d/business~solutions~engineering-

docs~en/Documents~rail-rack-matrix.pdf.aspx.

Section 1: Cabling a PowerEdge R520 system with a CMA

This section details how to cable the PowerEdge R520 system on sliding rails using a CMA. If you are

cabling the system without the optional CMA, refer to Section 3.

Follow the instructions contained in the Rack Installation Instructions in the sliding rail kit to install the

server into the rack. Once installed, use these instructions to install the cables. All illustrations in the

following sections were created using a PowerEdge R520 system.

NOTE: The PowerEdge R520 system is backward compatible with the PowerEdge R510 rails and CMA.

1.1. Connecting the cables to the system

Attach the CMA tray to the back of the rails as described in the CMA Installation Instructions provided

in the CMA kit. Connect all applicable cables to the rear of the system and verify that all connections

are secure. See Figure 1.

System with cables installedFigure 1.

Cable Routing Procedures for the Dell PowerEdge R520 System

1.2. Routing the power cables through the strain reliefs

After you have installed the tray and cables, route the power cable(s) through the strain relief(s)

located on the power supply handle(s) as shown in Figures 2 & 3.

Routing power cables through the strain reliefs on hot swap power suppliesFigure 2.

Routing the power cable through the strain relief on a fixed power supplyFigure 3.

1.3. Installing the CMA

The CMA can be installed on either the rear right or rear left side of the rails as described in the CMA

Installation Instructions. Mounting the CMA on the side that is opposite of the power supplies (left-side

mount) is recommended for systems with hot swap power supplies; otherwise, the CMA must be

partially disconnected in order to remove the outer power supply. Refer to Section 2 for details on

power supply replacement.

NOTE: If you are installing fiber-optic cables in the CMA, a cable bend radius of at least 1 inch must be

maintained throughout the length of the cable. It is recommended that fiber-optic cables be routed on

the exterior of the cable bundle to increase the bend radius of the fiber-optic cables through the CMA.

Additionally, a large amount of slack at the entrance and exit of the CMA is recommended.

1.3.1. Installing the inner CMA attachment bracket

As described in the CMA Installation Instructions, locate and attach the appropriate inner CMA

attachment bracket based on which side you wish to mount the CMA. Use the bracket marked “A” for

mounting the CMA on the left side, and the bracket marked “B” for mounting on the right side. See

Figure 4.

Cable Routing Procedures for the Dell PowerEdge R520 System

Attaching the inner CMA attachment bracketFigure 4.

1.3.2. Left-side mounting instructions

1. Install the CMA on the rear left side of the rails by attaching both CMA housings to the attachment

brackets on the rails.

2. Route the cables through the CMA while avoiding twisting the cables. Use the hook-and-loop straps

on the CMA to secure the cables.

3. If the cable bundle includes a keyboard, video, and mouse system interface pod (KVM SIP), it can

be placed inside the CMA basket when the CMA is mounted on the left side. See Figure 5.

Routing the cables through the CMAFigure 5.

4. Once you have routed all of the cables through the CMA, dress the cable slack between the back of

the system and the entrance of the CMA using the tie wraps provided in the CMA kit.

5. Clip off the excess length of material from the tie wraps. Make sure that the heads of the tie wraps

are positioned so as to avoid interference with adjacent systems. Return the CMA to the closed

(retracted) position.

NOTE:

Do not store excess cable

slack inside the CMA. The cables

may protrude through the CMA, thus

causing binding and potentially

damaging the cables.

Cables entering the CMA should have a

small amount of slack to avoid cable

strain when the CMA is extended.

KVM SIP can be placed inside the

basket when the CMA is mounted on

the left side.

Cable Routing Procedures for the Dell PowerEdge R520 System

6. Extend the system out of the rack to verify that there is sufficient slack in the cables on both ends

of the CMA.

See Figure 6 for an example of a completed left-side mounted CMA installation.

Left-side mounted CMA installation (preferred)Figure 6.

1.3.3. Right-side mounting instructions

Install the CMA on the rear right side of the rails by attaching both CMA housings to the attachment

brackets on the rails. The remaining steps are the same as for left-side mounting as described in

Section 1.3.2. See Figure 7 for an example of a completed right-side mounted CMA installation.

Right-side mounted CMA installation (CMA shown in service position)Figure 7.

Cable Routing Procedures for the Dell PowerEdge R520 System

Section 2: Replacing a hot swap power supply on a PowerEdge

R520 system with a CMA

2.1. Replacing a hot swap power supply with a left-side mounted CMA

1. Swing the CMA to its service position as described in the CMA Installation Instructions provided

with the CMA kit.

2. If the bottom power supply is being replaced, first remove the tray from underneath the CMA as

described in the CMA Installation Instructions. If the top power supply is being replaced, the tray

can remain in place.

3. Disengage the strain relief and disconnect the power cord from the power supply.

4. Replace the power supply.

5. Plug in the power cord, re-engage the strain relief, replace the CMA support tray (if necessary),

and return the CMA to the closed (retracted) position.

2.2. Replacing a hot swap power supply with a right-side mounted CMA

1. Swing the CMA to its service position as described in the CMA Installation Instructions provided

with the CMA kit.

2. If the bottom power supply is being replaced, first remove the tray from underneath the CMA as

described in the CMA Installation Instructions. If the top power supply is being replaced, the tray

can remain in place.

3. Disengage the strain relief and disconnect the power cord from the power supply.

4. Disconnect both CMA attachment housings from the brackets on the rails as shown in Figure 8.

5. Detach the inner CMA bracket from the rail by pushing on the end of the lock spring and lifting the

bracket up and to the left until it clears the standoffs on the rail.

6. While supporting the CMA with one hand, remove and replace the power supply with the other

hand as shown in Figure 9.

7. Reinstall the inner CMA bracket to the rail and reconnect the CMA to the brackets.

8. Plug in the power cord, re-engage the strain relief, replace the CMA support tray (if necessary),

and return the CMA to the closed (retracted) position.

Cable Routing Procedures for the Dell PowerEdge R520 System

Disconnecting the CMA attachment housingsFigure 8.

Replacing a hot swap power supplyFigure 9.

Cable Routing Procedures for the Dell PowerEdge R520 System

Section 3: Cabling a PowerEdge R520 system on sliding rails

without a CMA

NOTE: The CMA for the Dell PowerEdge R520 system is optional. Without the CMA installed, the system

must be powered down and all cables disconnected before it can be extended out of the rack.

3.1. Routing the cables

1. Connect all applicable cables to the rear of the system and verify that all connections are secure.

2. Using the hook-and-loop straps supplied with the rail kit, bundle the cables and secure them to

either the left or right outer CMA attachment bracket as described in the Rack Installation

Instructions. See Figure 10 for an example of data cables secured to the left outer CMA bracket and

power cables secured to the right outer CMA bracket (as viewed from the rear of the system).

Cable routing on sliding rails without a CMAFigure 10.

3.2. Removing the outer CMA brackets for shallow racks

If you are installing the system into a shallow rack (less than 1 meter deep) and you will not be

installing a CMA, the outer CMA brackets may be removed from the sliding rails if necessary in order to

allow the rails to fit properly into the rack. Remove the brackets by using a #2 Phillips screwdriver to

remove the screws that secure the brackets to the rails as shown in Figure 11. Use the hook-and-loop

straps supplied with the rail kit to secure the cables to the rack frame if desired.

Andere Handbücher für PowerEdge PDU Managed LED

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Dell Server Handbücher

Dell

Dell PowerEdge UPS 500T Bedienungsanleitung

Dell

Dell DR4300 Bedienungsanleitung

Dell

Dell PowerEdge R815 Bedienungsanleitung

Dell

Dell EMC ScaleIO Ready Node 14G Montageanleitung

Dell

Dell PowerEdge 400SC Technisches Handbuch

Dell

Dell Wyse 5000 Series Bedienungsanleitung

Dell

Dell External OEMR R910 Kurzanleitung

Dell

Dell PowerEdge C6100 Datenblatt

Dell

Dell PowerEdge R830 Bedienungsanleitung

Dell

Dell PowerEdge C8220 Bedienungsanleitung

Dell

Dell PowerVault LTO4-120HH Bedienungsanleitung

Dell

Dell PowerEdge 700 Leitfaden

Dell

Dell PowerEdge M915 Kurzanleitung

Dell

Dell poweredge t330 Bedienungsanleitung

Dell

Dell PowerVault 735N Stücklistenhandbuch

Dell

Dell EMC PowerEdge R7515 Handbuch

Dell

Dell PowerEdge T105 Systems Bedienungsanleitung

Dell

Dell POWEREDGE M905 Bedienungsanleitung

Dell

Dell PowerVault DL2300 Bedienungsanleitung

Dell

Dell PowerEdge R510 Bedienungsanleitung

Dell

Dell E75S Series Handbuch

Dell

Dell External OEMR R210II Bedienungsanleitung

Dell

Dell EMC PowerEdge E45S Series Handbuch

Dell

Dell EMC PowerEdge T350 3RRTM Handbuch

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Planet

Planet NAS-7410 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR635 V3 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY BX900 Bedienungsanleitung

Asus

Asus RS700DA-E6 PS4 Bedienungsanleitung

Vertiv

Vertiv Avocent ACS6000 Montage- und Wartungsanleitung

A & T Internationale

A & T Internationale Xserve Service-Handbuch