Dell PowerEdge R420 Bedienungsanleitung

Dell PowerEdge R520 And

PowerEdge R420 Systems

Second Processor

Installation–Information

Update

Install_proc.book Page 1 Friday, May 4, 2012 2:24 PM

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use of

your computer.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of

data and tells you how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal

injury, or death.

__________________

Information in this document is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.

is strictly forbidden.

Trademarks used in this text: Dell™, the DELL logo, and PowerEdge™, are trademarks of Dell Inc.

Othertrademarksandtradenamesmaybeusedinthispublicationtorefertoeithertheentitiesclaiming

the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and

trade names other than its own.

2012 - 05 Rev. A00

Install_proc.book Page 2 Friday, May 4, 2012 2:24 PM

Additonal Processor Installation 3

Overview

This document provides important information for installing the second

processor in Dell PowerEdge R520 and PowerEdge R420 systems.

Before You Begin

To install a second processor in your system, you must ensure that you have:

• Replaced the dummy fan in the FAN 6 slot with a cooling fan.

For more information on replacing the fan, see "Removing a Cooling Fan"

and "Installing a Cooling Fan" in the relevant Owner’s Manual on

support.dell.com

• Upgraded the riser cards as indicated in the table below:

For more information on replacing the riser cards, see "Expansion Cards

and Expansion-Card Risers"

and

Technical Specifications

in the Owner’s

Manual at

support.dell.com

NOTE: When selecting or upgrading your system configuration, verify the system

power consumption with the Dell Energy Smart Solution Advisor at dell.com/ESSA

to ensure optimum power utilization.

Table 1-1. Riser Upgrade Information

PowerEdge

System

Upgrade

From To

R520 Riser1_1P: One half-height,

half-length x4 link

Riser1_2P: One half-height,

half-length x16 link

Riser2_1P:

• One full-height, full-length x8

link

• Two full-height, half-length x4

link

Riser2_2P:

• One full-height, full-length x8

link

• Two full-height, half-length x8

link

R420 Riser1_1P: One half-height,

half-length x4 link

Riser1_2P: One half-height,

half length x16 link

Riser2_1P: One full-height,

half-length x16 link

Same as Riser2_1P

Install_proc.book Page 3 Friday, May 4, 2012 2:24 PM

4Additonal Processor Installation

Removing a Processor Blank

CAUTION: Many repairs may only be done by a certified service technician. You

should only perform troubleshooting and simple repairs as authorized in your

product documentation, or as directed by the online or telephone service and

support team. Damage due to servicing that is not authorized by Dell is not covered

by your warranty. Read and follow the safety instructions that came with the

product.

Before upgrading your system, download the latest system BIOS version

from

support.dell.com

and follow the instructions included in the

compressed download file to install the update on your system.

NOTE: You can update the system BIOS using the Dell Lifecycle Controller.

Turn off the system, including any attached peripherals, and disconnect

the system from the electrical outlet. When disconnected from AC power,

press and hold the power button for 10 seconds to fully drain the system of

stored power prior to removing the cover.

NOTE: It is recommended that you always use a static mat and static strap

while working on components in the interior of the system.

Open the system. See "Opening the System

in the Owner’s Manual.

Remove the cooling shroud. See "Removing the Cooling Shroud" in the

Owner’s Manual.

CAUTION: The processor blank is held in its socket under strong pressure.

Be aware that the release lever can spring up suddenly if not firmly grasped.

Position your thumb firmly over the processor-blank socket-release lever

and release the lever from the locked position by pushing down and out

from under the tab. Rotate the lever upward.

Rotate the processor shield upward and out of the way.

Lift the processor blank out of the socket and leave the release lever up so

that the socket is ready for the new processor. See Figure 1-1.

Install_proc.book Page 4 Friday, May 4, 2012 2:24 PM

Additonal Processor Installation 5

Figure 1-1. Removing and Installing a Processor Blank/Processor

1 processor blank/processor 2 processor shield

3 notches in processor (2) 4 socket keys (2)

5 ZIF socket 6 socket-release lever

Install_proc.book Page 5 Friday, May 4, 2012 2:24 PM

6Additonal Processor Installation

Installing the Second Processor

CAUTION: Only trained service technicians are authorized to remove the system

cover and access any of the components inside the system. Before you begin this

procedure, review the safety instructions that came with the system.

Ensure that you have followed the steps mentioned in "Before You Begin"

on page 3.

Unpack the new processor.

CAUTION: Positioning the processor incorrectly can permanently damage the

system board or the processor. Be careful not to bend the pins in the socket.

CAUTION: Do not use force to seat the processor. When the processor is

positioned correctly, it engages easily into the socket.

Align the notches in the processor with the socket keys on the ZIF socket

and set the processor lightly in the ZIF socket. See Figure 1-1.

Close the processor shield.

Using a clean lint-free cloth, remove the thermal grease from the heat sink.

CAUTION: Applying too much thermal grease can result in excess grease coming

in contact with and contaminating the processor socket.

Open the grease applicator included with your processor kit and apply all

of the thermal grease in the applicator to the center of the topside of the

new processor.

Place the heat sink on the processor.

Tighten the heat-sink retention sockets. See Figure 1-2.

Install_proc.book Page 6 Friday, May 4, 2012 2:24 PM

Additonal Processor Installation 7

Figure 1-2. Installing the Heat Sink

Install the cooling shroud. For more information, see "Installing the

Cooling Shroud" in the Owner’s Manual.

Close the system.

1 retention sockets (4) 2 heat sink

3 retention screws (4)

Install_proc.book Page 7 Friday, May 4, 2012 2:24 PM

8Additonal Processor Installation

Reconnect your system and peripherals to their electrical outlets, and turn

on the system.

Press <F2> to enter the System Setup and check that the processor

information matches the new system configuration.

Run the system diagnostics to verify that the new processor operates

correctly.

Install_proc.book Page 8 Friday, May 4, 2012 2:24 PM

Andere Handbücher für PowerEdge R420

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Dell Server Handbücher

Dell

Dell ECS EX Series Montageanleitung

Dell

Dell PowerEdge 4200 Series Bedienungsanleitung

Dell

Dell PowerEdge M420 Kurzanleitung

Dell

Dell PowerEdge NX182 Bedienungsanleitung

Dell

Dell PowerEdge M820 Systems Bedienungsanleitung

Dell

Dell FC4700 Bedienungsanleitung

Dell

Dell PowerEdge R805 System Allgemeine Anweisungen

Dell

Dell Dimension 2400 Series Bedienungsanleitung

Dell

Dell External OEMR XL R210II Kurzanleitung

Dell

Dell PowerEdge 2500SC Handbuch

Dell

Dell EMC VxRack FLEX Bedienungsanleitung

Dell

Dell EMC VxFlex Ready Node 14G Bedienungsanleitung

Dell

Dell PowerEdge M630 Bedienungsanleitung

Dell

Dell PowerEdge C1100 Bedienungsanleitung

Dell

Dell PowerEdge R530 Bedienungsanleitung

Dell

Dell Wyse7020 Bedienungsanleitung

Dell

Dell Precision FX100 Bedienungsanleitung

Dell

Dell Force10 C150 Bedienungsanleitung

Dell

Dell EMC PowerEdge R7515 Bedienungsanleitung

Dell

Dell PowerEdge T105 Systems Bedienungsanleitung

Dell

Dell EMC PowerEdge XE7440 Handbuch

Dell

Dell EMC PowerEdge R640 Handbuch

Dell

Dell EMC PowerEdge C6420 Bedienungsanleitung

Dell

Dell PowerEdge 2970 Technisches Handbuch

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Planet

Planet NAS-7410 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR635 V3 Bedienungsanleitung

Fujitsu

Fujitsu PRIMERGY BX900 Bedienungsanleitung

Asus

Asus RS700DA-E6 PS4 Bedienungsanleitung