DeLonghi HCX9115ECA Bedienungsanleitung

IMPORTANT

SAFEGUARDS

When using any electrical appliance, some basic safety

precautions should always be observed to reduce the risk

of re, electric shock, and/or injury to persons. Read all

instructions carefully before using the appliance. Specically:

Danger!

Failure to observe the warning may result in life threatening

injury by electric shock.

- The appliance must not be placed

immediately under a xed power

socket.

- Do not use the appliance outdoors.

- Do not operate any heater with

a damaged cord or plug or after

the heater malfunctions, has

been dropped or damaged in

any manner. Return heater

to authorized service facility

for examination, electrical or

mechanical adjustment, or repair.

- This heater is not intended for use in

bathrooms, laundry areas and similar

indoor locations. Never locate heater

where it may fall into a bath tub or

other water container.

- If the power cable is damaged, stop

using the product. Power cable must

be replaced by the manufacturer, an

authorised service centre or a qualied

electrician in order to eliminate all risk.

- Donotusethisheaterintheimmediate

surroundings of a bath, a shower and

sinks or a swimming pool.

- Do not insert or allow foreign objects

to enter any ventilation or exhaust

opening as this may cause an electric

shock, re, or damage the heater.

- CAUTION: to prevent electric shock

match wide blade of plug to wide

slot, then fully insert.

- CAUTION: In order to avoid a hazard

due to inadvertent resetting of

thermal cutout, this appliance must

not be supplied through an external

switching device, such as a timer, or

connected to a circuit that is regulary

switched on and o by the utility.

- This heater may include an visual

alarm to warn that parts of the heater

are getting excessively hot. If the

alarm ashes, immediately turn the

heater o and inspect for any objects

on or adjacent to the heater that

may cause high temperatures. DO

NOT OPERATE THE HEATER WITH THE

ALARM FLASHING.

- If you intend to x your appliance to

the wall, make sure that the switch or

other control devices are not within

reach of persons in the bath or shower.

Important!

Failure to observe the warning could result in injury or

damage to the appliance.

- The appliance is not intended for use

by persons (including children) with

reduced physical, sensory or mental

capabilities, or lack of experience

and knowledge, unless they have

been given supervision or instruction

concerning use of the appliance by

a person responsible for their safety.

Children should be supervised to

ensure that they do not play with the

appliance.

- CAUTION — Some parts of this

product can become very hot and

cause burns.

- Extremecautionisnecessary when any

heater is used by or near children and

whenever the heater is leftoperating

and unattended.

- Always disconnect the plug from the

power outlet when the appliance is

not in use.

- Do not wrap the cord around the appli-

ance immediately after use.

- The internal parts of the appliance can

become very hot or produce sparks

during operation. Do not use the

appliance in areas where gasoline,

paints, or other ammable liquids are

used or stored.

- Use this heater only as described

in this manual. Any other use not

recommended by the manufacturer

may cause re, electric shock, or injury

to persons.

- Topreventoverloadandblownfuses,be

surethat no other appliance is plugged

into the same outlet (receptacle) or

into another outlet (receptacle) wired

into the same circuit.

- Make sure that the plug is fully

inserted into the outlet. Wall outlets

may deteriorate with time, so check

the plug periodically for signs of

overheating or deformation. If the

outlet has deteriorated, stop using it

and have it repaired.

- Do not use the appliance in small

rooms when they are occupied by

persons that are not capable of leaving

the room, unless constant supervision

is provided.

Danger of burns!!

Failure to observe the warning could result in burns or scalds.

- Do not use the appliance on soft

surfaces, such as beds, where the

openings may become blocked.

- This heater is hot when in use. To

prevent burns, do not let bare skin

touch hot surfaces. Use handle when

moving this heater. To prevent burns,

do not touch hot surfaces with bare

skin. Use the handle when moving

the appliance. Keep all ammable

materials, such as furniture, pillows,

bedding, paper, clothing, and curtains

at least 3 feet (90 cm) from the front

and top of the appliance also avoid

contact with the sides and back.

- Do not run cord under carpeting.

Do not cover cord with throw rugs,

runners, or the like. Arrange cord away

from trac area and where it will not

be tripped over.

- It is normal for the heater’s plug and

cord to feel warm to the touch. A

plug or cord which becomes hot tothe

touch or becomes distorted in shape

may be a result of a worn electrical

outlet. Worn outlets or receptacles

should be replaced prior to further use

of the heater. Plugging heater into a

worn outlet /receptacle/ may result in

overheating of the power cord or re.

- WARNING: Do not cover the appliance

while it is functioning in order to avoid

overheating which may cause risk of

re.

Symbol meaning

This simbol indicates:

(If provided) Class II equipment

Please note:

This symbol indicates recommendations and important

information for the user.

-If your appliance is equipped with a

polythene tape used as carry handle,

remove it before connecting appliance

to the outlet.

- Always use the appliance in an upright

position.

- To disconnect heater, turn controls to

o, then remove plug from outlet.

- Connect to properly polarized outlets

only.

- This heater is not intended for use with

an extension cord or outlet strip. Plug

the cord directly into an appropriate

wall receptable.

- Check that neither the appliance nor

the power cable have been damaged

in any way during transportation.

- Makesurethatnopiecesofpolystyrene

or other packaging material have

been left on the appliance. It may be

necessary to pass over the appliance

with a vacuum cleaner.

- When switching on the appliance for

the rst time, allow it to run at full

power for at least two hours to get

rid of the unpleasant smell. Make

sure that the room in which the

appliance is located is well ventilated

during this operation. It is normal for

the appliance to emit small cracking

sounds when you turn it on.

- Do not use the appliance in rooms with

a oor area of less than 4m².

- Before putting the appliance away,

make sure it is completely o and

unplugged from the mains socket.

Wrap the cable around the base.

Do not store in dusty atmospheres.

- Do not rest anything on the appliance.

- Do not obstruct the air intake and

outlet grilles (danger of overheating).

- Do not place the heater near a bed

because objects such as pillows or

blankets can fall o the bed and be

ignited by the heater.

- A tip over safety device turns the

appliance o if it falls over or is

positioned inappropriately in such

a way as to jeopardise safety. The

appliance emits a beep and a dot

ashes on the display. The appliance

resumes operation a few seconds after

being placed in an upright position

again.

See troubleshooting session.

SAVE THESE

INSTRUCTIONS

THIS PRODUCT IS FOR HOUSEHOLD USE

ONLY

DESCRIPTION

A Power indicator light

B ON/OFF button

C +/- adjustment buttons

D MODE button (selects the operating mode)

E “ECO plus”button

F Timer button

General instructions

Remove the heater from the packaging. Check that neither

the heater nor the power cable has been damaged during

transport.

Do not operate the heater if damaged. Remove all publicity

material present on the appliance. The appliance is suitable

for free-standing or wall-mounted usage. Do not assemble

the feet if wall-mounted.

Electrical connection

- Before connecting the appliance to the current outlet,

check that the voltage indicated on the appliance rating

plate is the same as your electric plant and that it can

stand the power consumption (Watt) indicated by the

labelling.

- If more than one appliance is used at once, it is

important to ensure that the electric plant is able to

support the power required.

Mounting the feet

Turn the appliance upside down on a rug or soft surface in

order to prevent damaging the paint nish.

Fix the feet to the appliance with the nr. 4 screws 4.8x13 PH

Gsupplied (see g. 1), 2 screws for each foot.

Wall-Mounting Installation

The wall mounting kit contains:

4 metal brackets (H)

4 screws 4.5x25PH (I)

2 buttery screws M5 (J)

4 plastic anchors 6x30 (K)

Required tools for assembly and estimated assembly

time

Drill

Screwdriver PH 2 x 100 (Phillips type)

Estimated assembly time: 30 minutes

Before installing the unit , make sure of the following:

- The appliance must not be located directly

beneath a current outlet.

- The plug and outlet must be easy to reach after

installation.

- No electric cables or other pipes could be

damaged during the installation.

- Keep away from curtains or ammable materials.

To wall-mount, proceed as follows:

Turn the appliance upside down on a at stable surface. Fix

the 2 brackets Hwith the 2 buttery screws Jas shown in

Fig. 2. For brick walls use a 6 mm concrete drill bit. For plaster

board or drywall, it is recommended to use appropriate

screws and anchors (not supplied).

- Before drilling the wall, mark the exact points,

respecting the minimum distances as shown in g. 3.

- Drill the wall where previously marked, and insert the

plastic anchors K.

- Fix the 2 metal brackets H using the two screws I

provided.

- Hang the appliance on the bracket.

- Mark out the 2 lower xing points. Remove the

appliance, drill the lower holes and insert the wall

anchors K.

- Now, you can hang back the heater on the bracket and

x the lower part of the appliance with the 2 remaining

screws I.

USE

Operation and use

- Plug into the outlet socket.

- The appliance emits a beep. The power indicator light

(A) comes on and remains lit while the appliance is

powered.

- The appliance switches to stand-by.

- Press the ON/OFF (B) to turn the appliance on. It begins

heating the room according to the current settings.

- Press the MODE (D) button to select one of the following

operating modes:

- Freeze prevention

In this mode, the appliance keeps the room at a

temperature of 45°F (7°C) to avoid freezing.

- Heating 1, 2, 3 and Heating 3 + Fan

Inthis mode, the desired temperaturecan beselectedby

pressing the adjustment buttons + and –. By pushing

the + or - button once, the temperature (shown on the

display) will increase or decrease by 1 degree.

Heating 1

The appliance operates at low power.

Heating 2

The appliance operates at medium power.

Heating 3

The appliance operates at high power.

Heating 3 + Fan

The appliance operates at the maximum power with

the fan.The setting temperature range available is from

60°F to 90°F (16°C to 32°C).

“ECO plus” function

The “ECO plus” function is available in Heating 1, 2 3 and 3

+ fan modes only. To activate the function, press the “ECO

plus”(E) button.

When this function is active the appliance automatically sets

the most appropriate power level to guarantee optimum

comfort while reducing energy consumption. While the

“ECO plus” function is active, the appliance may switch

automatically to a lower heating power than the one

displayed.

Working indicator

The symbol indicates the heating status by means of its

colors.

RED: the unit is heating at the maximum power.

YELLOW: the unit is heating at the medium power.

GREEN: the unit is heating at the minimum power.

absent: the unit is not heating.

Brightness of the display

The appliance allows two dierent brightness settings for the

display.

The highest is active when any key button is pressed.

After a few seconds of keyboard inactivity, the brightness will

decrease to the operating brightness level.

Key lock

In order to avoid accidental operation, you can lock the

keyboard using the keylock function.

To activate this function press buttons + and - (C) together

for at least 3 seconds. The display shows the symbol and

a double acoustic signal will be emitted. To deactivate the

function proceed in the same way.

Timer function

This function can be activated in two dierent ways.

Delayed start: With the appliance OFF press the timer

button (F) .The symbol is displayed ashing together

with the hours left before the appliance comes on. Change

the hours using the + and - (C) buttons, then wait a few

seconds for the program to be stored.

The display will return to o and the symbols remains on.

When the programmed time has elapsed, the appliance will

come on with the previous settings.

Delayed stop: with the appliance ON,pressthetimer button

(F). The symbol is displayed ashing together with

the hours left before the appliance goes on-standby. Change

the hours using the + and - (C) buttons, then wait a few

seconds for the program to be stored. The current settings

and symbol are displayed.

At the end of the set time the appliance switches on-standby

automatically. To go back to operating without the timer,

press the timer button twice.

The timer symbol disappears from the display.

Please note: the time is settable from 0.5 to 24 hours.

Changing of the temperature scale

The display can show the temperature in both °F (Fahrenheit)

and °C (Celsius). To select the desired temperature scale,

when the unit is in standby position, press and hold the "+"

key for at least 10 seconds, then release.

The change of scale will be indicated by two short beeps.

SAFETY FUNCTIONS

- Safety device: The appliance is tted with a safety

cuto device which will switch the appliance o in case

of accidental overheating. To reset the cuto, disconnect

the plug from the power supply for a few minutes,

remove the cause of overheating, then reconnect the

appliance. If this abnormal situation happens several

times, contact customer service.

- Tip-oversafety device:Thisdeviceturnsthe appliance

o if it falls over or is positioned inappropriately in such

a way as to jeopardize safety. The appliance emits a

beep and a dot ashes on the display. The appliance

resumes operation a few seconds after being placed in

an upright position again.

Alarms

The appliance has a diagnostic system that makes it possible

to signal malfunctions.

In case of problems, the display will show an alarm message:

(Probe failure) and (High temperature),

see

troubleshooting section.

MAINTENANCE

Before carrying out any maintenance, unplug the heater

from the outlet and wait for it to cool o completely.

This heater requires no particular maintenance. It is

sucient to remove the dust with a soft, dry cloth.

Never use abrasive powders or solvents. If necessary

remove concentrated areas of dirt with a vacuum cleaner.

WARNING: any other servicing should be performed by an

authorized representative.

Should the heater not be in use over a certain length of time,

roll the cable around the feet and store it in a dry place.

TROUBLESHOOTING

PROBLEM CAUSE SOLUTION

The appliance doesn't work Be sure it is plugged in and that the electrical

outlet is working

The temperature may be set too low

The Key lock may be activated

Plug into the power outlet

Set the temperature to a higher

position

See the section "Key lock"

The display shows a blinking

dot and you hear an intermittend

"beep"

The appliance could be tipped over or is

positioned in an improper way

Make sure the appliance is standing

upright on a at surface. Position the

appliance correctly

The display shows "PF"The temperature sensor is malfunctioning Contact the De longhi toll free number

The display shows "Ht" blinking The internal temperature is too high.

The air intake or outlet grille is obstructed

Check the appliance is correctly

positioned respecting the minum

distances from the wall, or objects, as

indicated on the instruction manual, if

not, position the appliance correctly

Remove the obstruction

Disconnect theplug from the outlet and

let the appliance cool down. After few

minutes plug the appliance again. If the

appliance doesn't work please contact

the De longhi toll free number

Inhaltsverzeichnis

Andere DeLonghi Heizung Handbücher

DeLonghi

DeLonghi TRD40615ECA Bedienungsanleitung

DeLonghi

DeLonghi HFS50 Series Bedienungsanleitung

DeLonghi

DeLonghi HCS Bedienungsanleitung

DeLonghi

DeLonghi HVF3533 Bedienungsanleitung

DeLonghi

DeLonghi HBC3052T Bedienungsanleitung

DeLonghi

DeLonghi DCH 6031 Bedienungsanleitung

DeLonghi

DeLonghi BAMBINO Bedienungsanleitung

DeLonghi

DeLonghi TRD50615ECA Bedienungsanleitung

DeLonghi

DeLonghi EW 7707CM Bedienungsanleitung

DeLonghi

DeLonghi CERAMIC FAN HEATER Bedienungsanleitung

DeLonghi

DeLonghi HVY1020 Mini Bedienungsanleitung

DeLonghi

DeLonghi HMH550-3R Bedienungsanleitung

DeLonghi

DeLonghi SCF 1000 Bedienungsanleitung

DeLonghi

DeLonghi HBP Series Bedienungsanleitung

DeLonghi

DeLonghi Electric oil Filled Radiator Bedienungsanleitung

DeLonghi

DeLonghi 6507L Installationsanleitung

DeLonghi

DeLonghi TRD41500ET Bedienungsanleitung

DeLonghi

DeLonghi CATALYTIC HEATER Bedienungsanleitung

DeLonghi

DeLonghi DCH4120 Bedienungsanleitung

DeLonghi

DeLonghi SRI Bedienungsanleitung

DeLonghi

DeLonghi DCH6031 Bedienungsanleitung

DeLonghi

DeLonghi TRD40615EBK Bedienungsanleitung

DeLonghi

DeLonghi HSX2320 Series Bedienungsanleitung

DeLonghi

DeLonghi HFX30 Series Bedienungsanleitung

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

IRSAP

IRSAP The Radiator Company Ovali Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung