Delta UNOnext Bedienungsanleitung

1

UNOnext Wiring Guide

ver 1.5

2021/6/23

2

As long as UNOcentral is connected to a power supply, the system will begin to operate.

Through the HDMI connection on the back of UNOcentral, UNOcentral's screen can be output

to displays with HDMI interfaces, such as computer monitors and TVs. UNOcentral is managed

through a web GUI. Users can remotely manage UNOcentral through the browsers of other

hosts, or directly output UNOcentral to a display and use a USB keyboard and mouse for man-

agement. To use UNOcentral remote management or other network services, it is recommend-

ed to connect the network cable to the LAN1 port on the back of UNOcentral (The MAC address

of LAN1 is provided on the UNOcentral’s label). As shown in Figure 1

If RS485 communication interface is used between UNOcentral and UNOnext, they must be

used Daisy-Chain, and the communication mode is Modbus/RTU protocol. It is recommend-

ed to use 22AWG multi-core shielded twisted pair cable or above to achieve the best re-

sults. The simple wiring instructions is below, please use the RS485 adapter include in the

box (Please plug-in on the COM1 of the UNOcentral).

3

UNOnext can directly connect to a controller with RS485 interface, up to 16 devices can be connect-

ed to one controller.

If the UART sengs of UNOnext have been modied, please modify to the default sengs

above before connecng to UNOcentral.

The Modbus slave address of UNOnext can be set by dip switch following below table. Oth-

ers detail UNOnext sengs can be referred the UNOnext user manual. Table 2 Set Modbus slave

address of UNOnext

The UART conguraons of the UNOcentral and UNOnext

Baud Rate: 9600

Data-bit: 8

Parity: None

Stop-bit: 1

4

1. Prepare tools and connector.

2. Connect signal lines.

3. Tighten the screws 4. Need to fix the plastic sheet.

Step of operation.

5

5. Close the lid

6. Install connector on the COM1 of UNOcentral

6

7. Connect the HDMI cable, mouse, and keyboard to the screen to confirm that the number of

UNOnext is the same as the number and sensor data are shown on the screen.

If the sensor data does not show value at all or the number of devices is incorrect, please

check below checklists

◇Are all UNOnext power on?

◇Is RS485 wiring problem?

◇Do use the wrong pin hole?

◇Does follow RS485 installation guideline?

◇All of UNOnext should be used different modbus slave address.

Inhaltsverzeichnis

Andere Delta Messgerät Handbücher

Delta

Delta WS-6975 Bedienungsanleitung

Delta

Delta DPM-C520 Bedienungsanleitung

Delta

Delta CS-LDM-50M Bedienungsanleitung

Delta

Delta TECK II Bedienungsanleitung

Delta

Delta TZU-22 Bedienungsanleitung

Delta

Delta ZS1000-A-V2 Bedienungsanleitung

Delta

Delta DPM-C530 Bedienungsanleitung

Delta

Delta HD2114.0 Bedienungsanleitung

Delta

Delta XVR5432L-I2 Bedienungsanleitung

Delta

Delta DPM-C501L Bedienungsanleitung

Delta

Delta DPM-C510 Bedienungsanleitung

Delta

Delta UNO-C07X011 Bedienungsanleitung

Delta

Delta DPM-D510 Bedienungsanleitung

Delta

Delta DVP08NTC-S Bedienungsanleitung

Delta

Delta DPM-C530A Bedienungsanleitung

Delta

Delta OR-AE-1306 Bedienungsanleitung

Delta

Delta PPM P1_120 Bedienungsanleitung

Delta

Delta R4E Bedienungsanleitung

Delta

Delta DPM-C320 Bedienungsanleitung

Delta

Delta RetroSign GRX Bedienungsanleitung

Delta

Delta REVEZ-HD-TRIO DVB-T/T2 Bedienungsanleitung

Delta

Delta LTL2000S Bedienungsanleitung

Delta

Delta LTL-X Mark II Bedienungsanleitung

Delta

Delta LD-100E-M22 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung