Denver CR-416 Bedienungsanleitung

CR-416

INSTRUCTION MANUAL

BRUKSANVISNING

BETJENINGSVEJLEDNING

BEDIENUNGSANLEITUNG

MANUAL DE INSTRUÇÕES

INSTRUCCIONES DE USO

KÄYTTÖOHJEET

GEBRUIKERSHANDLEIDING

INSTRUKCJA OBSLUGI

www.denver-electronics.com

www.facebook.com/denverelectronics

English

FUNCTION AND CONTROLS

1. MEMORY.SET / MEMORY+ / DISPLAY LIGHT AUTO ON/OFF /

NAP

2. ALARM 1 ON / OFF SET

3. ALARM 2 ON / OFF SET

4. SNOOZE / SLEEP / DIMMER

5. CLK.ADJ. (TIME SET) / TEMP

6. << / TUNE -/ YEAR/MONTH/DAY

7. >> / TUNE + / DST/C-F

8. VOLUME UP / DISPLAY AUTO CHANGE ON/OFF

9. ON/OFF

10. VOLUME DOWN

11. DISPLAY

12. BATTERY COMPARTMENT (REAR OF UNIT)

13. RESET

14. RATING LABEL (REAR OF UNIT)

15. SPEAKER

16. TEMPERATURE SENSOR (IN DOOR)

17. FM ANTENNA

18. AC POWER CORD

POWER CONNECTION

Plug the AC power cord to a household outlet AC source. This unit

is equipped with a battery back up system, it requires a 3V CR2032

at lithium battery (not included). Insert the battery in the battery

compartment, making certain that the positive and negative (+ and -)

battery terminals are attached to the corresponding terminals on the

plate in the battery compartment. If an AC power failure occurs, the

clock automatically switches to the battery power supply, the clock and

timer memory continue running. When the AC power resumes, the clock

switches back to AC again.

GETTING STARTED

Press the RESET button (13) locates on the back of unit after AC plug

in.

- The unit will display full segment for 2 seconds, then it will enter the

normal mode.

1. TIME AND CALENDAR MANUAL SETTING

A. Setting Time and Calendar – Press Time set button (5) in normal

mode and keep depress over 2 seconds to enter time set mode,

after enter the setting mode, press Time set button (5) to change the

mode cycle as follows :

Normal → Year → Month → Day → 12/24 H → Real time Hour → Real

time Min → Normal

Action (during data adjustment):

- Press << / Tune -button (6) to adjust data backward.

- Press >> / Tune + button (7) to adjust data forward.

- Keep depress << or >> button for 2 seconds to enable auto forward.

LED DISPLAY

TIME Indicator

MHz Indicator

ALARM 2 Indicator

PM Indicator

SANDBYIndicator

ALARM 1Indicator

B. Setting Alarm 1 and Alarm 2 – Press alarm set button (2/3) during

normal mode and keep depress over 2 seconds to enter alarm set

mode, after enter the setting mode, press alarm set button (2/3) to

change the mode cycle as follows :

Normal → AL 1 Hour → AL1 Min → AL 1 weekday Alarm → AL 1 wake

beep → AL 1 wake radio → AL 1 wake radio volume → Normal

Normal → AL 2 Hour → AL2 Min → AL 2 weekday Alarm → AL 2 wake

beep → AL 2 wake radio → AL 2 wake radio volume → Normal

Select alarm weekday mode as follows

1-5 : Monday to Friday

1-7 : Whole week

6-7 : Saturday & Sunday

1-1 : One day of week

Action (during data adjustment) :

- Press << / Tune -button (6) to adjust data backward.

- Press >> / Tune + button (7) to adjust data forward.

- Keep depress << or >> button for 2 seconds to enable auto forward.

2. SETTING ALARM OUTPUT ON/OFF

Press MEMORY.SET / MEMORY+ / DISPLAY LIGHT AUTO ON/OFF

/ NAP button (1) to the Auto off mode, alarm wake up the display is

auto turn on.

Press alarm 1 on/off set button (2) to toggle on and off alarm output

function.

Press alarm 2 on/off set button (3) to toggle on and off alarm output

function.

3. ALARM DURATION AND SNOOZE FUNCTION

Alarm Duration – Beep alarm or radio alarm will continue output for

30 minutes if no key press, then it will stop automatically and wait for

same alarm time on next day.

Action for Snooze :

- During alarming, press Snooze button (4) will enable snooze

function, Beep alarm or Radio alarm will stop.

- Snooze interval is 9 minute (not include second offset)

- Snooze will continue unless press ON/OFF button (12) to alarm off

of Buzzer alarm or Radio Alarm stop automatically after 30 minutes.

Press MEMORY.SET / MEMORY+ / DISPLAY LIGHT AUTO ON/OFF

/ NAP button (1) to the Auto off mode, during alarming display auto

turn on, press snooze / sleep button (4) will enable snooze function,

buzzer alarm or radio / display will stop & off.

4. CHANGE DISPLAY CONTENT Press << / Tune -/ YEAR/MONTH/

DAY button (6) during normal can switch to display Year / Month /

Day, after 5 seconds timeout and return back to display time.

Listening to Radio

Press the ON/OFF button (9) to turn the unit on. Use the Tune + or

Tune – button to select the desired FM station. If you press and hold

the Tune + or Tune – button for one second, the release, the unit will

automatically scan to the next broadcasting station. Press the ON/OFF

button (9) to turn the radio OFF.

To set / recall the radio presets

Press the ON/OFF button (9) to turn the unit ON.

Use the Tune + or Tune -button to select the desired FM station.

Press the memory / memory + button; “P01” will blink in the display.

Press the memory / memory + button again to set the preset.

Repeat steps 2 through 4 to set more presets.

The unit can preset 10 stations totally for FM.

When “P01-P10” is blinking, press the Tune+ or Tune-button to select

YEAR Indicator

MONTH Indicator DAY Indicator

the preset number.

When recalling preset stations, press memory / memory + to select the

preset number.

Sleep operation

When listening to radio, press Snooze / Sleep button (4) to enter sleep

mode. You can just adjust the sleep timer from 90 mins to 15 mins by

pressing the Snooze / Sleep button (4). The unit will automatically turn

off after the selected time.

NAP timer function (count down timer)

During radio off mode, press MEMORY.SET / MEMORY+ / DISPLAY

LIGHT AUTO ON/OFF / NAP button (1) to turn on NAP mode, the NAP

time will keep by 5 seconds, within 5 seconds and press MEMORY.

SET / MEMORY+ / DISPLAY LIGHT AUTO ON/OFF / NAP button (1)

button can change the duration from 90 min – 10 min. The alarm buzzer

will sound for 30 min and then shut off automatically. To stop the alarm

buzzer, press the ON/OFF button (9).

Press the MEMORY.SET / MEMORY+ / DISPLAY LIGHT AUTO ON/

OFF / NAP button (1) has no effect during alram operation. Press ON/

OFF button (9) to cancel NAP function.

SPECIFICATIONS

Frequency range : FM 87.5 – 108 MHz

Battery backup : 3V (CR2032 Flat Lithium battery x 1) not included

Power supply : AC230V 50Hz

RESET

The reset button is located on the back of unit. Use a ballpoint pen to

press it whenever you change the batteries, or unit is not performing as

expected. This will return all settings to default value, and you will lose

any stored data (alarm and clock settings).

Note :

- Ensure that the FM antenna is completely unrolled and extended for

best FM reception.

WARNING

1 No naked ame sources, such as lighted candles, should be placed

on the apparatus.

2 Do not place the product in closed bookcases or racks without

proper ventilation.

3 Where the mains plug is used as the disconnect device, the

disconnect device shall remain readily operable.

4 The ventilation should not be impeded by covering the ventilation

openings with items, such as newspapers, table-cloths, curtains,

etc.

5 It shall not be exposed to dripping or splashing and that no objects

lled with liquids, such as vases, shall be placed on the apparatus.

6 Do not connect FM antenna to outside antenna.

7 The unit should not be exposed to direct sunlight, very high or low

temperature, moisture, vibrations or placed in dusty environment.

8 Do not use abrasive, benzene, thinner or other solvents to clean the

surface of the unit. To clean, wipe it will mild non-abrasive detergent

solution and clean soft cloth.

9 Never attempt to insert wires, pins or other such objects into the

vents or opening of the unit.

10. Disconnect device warning : Mains plug is used as the connection,

so it should always remain ready operate.

11.Batteries shall not be exposed to excessive heat such as sunshine,

re or the like.

12.Class 1LED product.

CAUTION

Danger of explosion if battery is incorrectly replaced Replace only with

the same or equivalent type

Electric and electronic equipment contains materials, components and

substances that can be hazardous to your health and the environment,

if the waste material (discarded electric and electronic equipment) is

not handled correctly.

Electric and electronic equipment is marked with the crossed out trash

can symbol, seen below. This symbol signies that electric and

electronic equipment should not be disposed of with other household

waste, but should be disposed of separately.

All cities have established collection points, where electric and

electronic equipment can either be submitted free of charge at recycling

stations and other collection sites, or be collected from the households.

Additional information is available at the technical department of your

city.

DENVER ELECTRONICS A/S

www.denver-electronics.com

www.facebook.com/denverelectronics

Swedish

FUNKTIONER OCH KONTROLLER

1. Minne/Minne Upp/Display ljus auto på/av/NAP

2. Alarm 1 På / Av / inställt

3. Alarm 2 På / Av / Inställt

4. Snooze / Sleep / DIMMER

5. Tid inst/temp Radio frekvens

6. « / Inställning - / ÅR / DAG

7. » / Inställning + /C-F/ DST

8. Volym Up / Display auto ändring på/av

9. PÅ/AV

10. Minska Volym

11. Display

12. Batterfack (bak på enheten)

13. ÅTERSTÄLL

14. Klassiceringsetikett (bak på enheten)

15. HÖGTALARE

16. TEMPERATURGIVARE (INOMHUS)

17. FM Antenn

18. AC STRÖMSLADD

STRÖMANSLUTNING

Anslut strömsladden till ett vägguttag för växelström. Denna apparat

är försedd med ett uppbackningssystem, det kräver ett 3V CR2032

platt litiumbatteri (ingår inte). Lägg i batteriet i batterifacket, se till

att batteriets positiva och negativa (+ och -) batteripolerna ansluts

till motsvarande poler på plattan i batterfacket. Uppstår ett fel på

växelströmförsörjningen, kopplar klockan automatiskt till batterkraft,

klockan och tidminnet fortsätter att gå. När växelströmmen återkommer,

kopplar klockaan automatiskt tillbaka till huvudströmmen.

KOMMA IGÅNG

Efter att kontakten anslutits tryck återställningsknappen (13) placerad

på enhetens baksida.

- Enheten visar helt segment i 2 sekunder, därefter normalt läge.

1. MANUELL INSTÄLLNING AV TID OCH DATUM

A. Ställa in tid och datum - Tryck tidknappen (5) i normalt läge och

håll nedtryckt i 2 sekunder för att öppna inställningsläge tid, efter att

inställningsläget öppnats tryck tidknappen (5) för att ändra

lägescykeln som följer :

Normal → År → Månad → Dag → 12/24 tim → RTC tim → RTC Min →

Normal

Aktivitet (vid datajustering)

- Tryck << / Inställning- knappen (6) för att justera data bakåt

- Tryck << / Inställning + (7) för att justera data framåt

- Håll nedtryckt « eller» knappen i 2 sekunder för att aktivera auto

fram.

B. Ställa in Alarm 1 och Alarm 2 - Tryck alarmknappen (2/3) i normalt

läge och håll nedtryckt i 2 sekunder för att öppna inställningsläge

alarm, efter att inställningsläget öppnats tryck alarmknappen (2/3) för

LED DISPLAY

Tidsindikering

MHz Indikering

ALARM 2 indikering

PM indikering

STANDBY Indikering

ALARM 1 indikering

Inhaltsverzeichnis

Sprachen:

Andere Denver Radiowecker Handbücher

Denver

Denver CRL-330 Bedienungsanleitung

Denver

Denver CRL-330 Bedienungsanleitung

Denver

Denver CR-323 Bedienungsanleitung

Denver

Denver TR-52 Technisches Datenblatt

Denver

Denver CR-918BLACK Bedienungsanleitung

Denver

Denver CRP-121 Bedienungsanleitung

Denver

Denver CRI-812 Bedienungsanleitung

Denver

Denver CRP-515 Bedienungsanleitung

Denver

Denver CR-418 Bedienungsanleitung

Denver

Denver CRP-112 Bedienungsanleitung

Denver

Denver CR-490 Bedienungsanleitung

Denver

Denver CRP-210 Bedienungsanleitung

Denver

Denver CR-812 Bedienungsanleitung

Denver

Denver CR-715 Bedienungsanleitung

Denver

Denver CRL-290 Bedienungsanleitung

Denver

Denver CRP-718 Bedienungsanleitung

Denver

Denver CR-419 Bedienungsanleitung

Denver

Denver CRP-717 Bedienungsanleitung

Denver

Denver IFM-90 Bedienungsanleitung

Denver

Denver CR-419 MK2 Bedienungsanleitung

Denver

Denver CRL-330 Bedienungsanleitung

Denver

Denver CRL-340 Bedienungsanleitung

Denver

Denver CR-412 Bedienungsanleitung

Denver

Denver CR-421 Bedienungsanleitung

Beliebte Radiowecker Handbücher anderer Marken

Audiovox

Audiovox CE90 Bedienungsanleitung

Sony

Sony Dream Machine ICF-C763L Bedienungsanleitung

Sanyo

Sanyo DMP-P6 Bedienungsanleitung

Yamaha

Yamaha ISX-80 Bedienungsanleitung

Pyle

Pyle PLMR20W Bedienungsanleitung

Blaupunkt

Blaupunkt CR7BK Bedienungsanleitung

Philips

Philips AJ3180 Bedienungsanleitung

HoMedics

HoMedics SS-5500-2EU Bedienungsanleitung

RCA

RCA RC66i Bedienungsanleitung

Versaudio

Versaudio Vers Bedienungsanleitung

SOUNDMASTER

SOUNDMASTER UR8100 Bedienungsanleitung

Audiovox

Audiovox CE90 Bedienungsanleitung

Jensen Audio

Jensen Audio JCR-222 - AM/FM Projection Alarm Clock Radio Bedienungsanleitung

Roberts

Roberts ChronoDAB Bedienungsanleitung

AEG

AEG MRC 4132 BT Bedienungsanleitung

Tokai

Tokai TC-155 Bedienungsanleitung

Timex

Timex T300 Bedienungsanleitung

Sony

Sony DREAM MACHINE ICF-C318 Bedienungsanleitung