Desa GA3400T Bedienungsanleitung

WARNING: Fan accessory must be grounded.

Fan comes with a three-prong, grounding plug as

showninFigure1.Theplugisyourprotectionagainst

electrical shock. Plug it into a standard, three-hole,

grounded, outlet. If cord needs replacing, use only a

cord with a three-prong, grounding plug.

GA3400T / GA3450T

Thermostat Blower Accessory

If any of these pieces are missing or damaged, contact the dealer

where you purchased this kit or DESA International at 1-800-972-

7879 for referral information.

Grounding Plug

Figure 1 - Grounding Plug

Grounded Outlet

NOTICE: Cord length from switch plate assembly to

plug is six feet. Make sure grounded outlet is an

appropriate distance from unit.

Hardware kit contains

2 Plastic snap bushings

6 #10 screws

1 Plug button

For use on Fireplace models VMH26 Series, VMH10 Series, CGCF Series, CF26 Series, and FMH26 Series.

See the owner’s manual supplied with your Fireplace for specific installation instructions.

WARNING: Failure to connect all wires as indi-

cated may cause electrical shock or personal injury.

Carton Contents

Description Part Number

Bracket 103966-01

Thermodisc 103972-01

Blower 103283-01

Wire Harness 103968-01

Power Cord 104015-01

AUTO/OFF/ON switch 099998-01

Mounting Hardware kit 098418-08

DESA INTERNATIONAL

REMOVING UPPER LOUVER ASSEMBLY

(For all models except CF26 Series)

To install the blower accessory, you must first remove the upper

louver assembly, hood, and branch support.

1. Lift screen off heater and remove log set.

2. If you have extruded louvers, remove 4 screws from louver

assembly (see Figure 2). If you have sheet metal louver, re-

move 2 screws from louver assembly and 4 screws from hood

(if installed) (see Figure 3). Save these screws.

3. Pull louver assembly straight out from the cabinet. Be careful not

to scratch the paint. Set louver assembly, hood and screws aside.

4. Remove 2 screws from each side of branch support and pull

branch support out (see Figure 2).

Upper Louver

Assembly

Blower Bracket

Mounting Holes

Figure 3 - Removing Hood and Upper Sheet Metal Louver

Assembly

Hood

Continued

Figure 2 - Removing Upper Extruded Louver Assembly and

Branch Support

Blower Bracket Mounting Holes

Upper Louver

Assembly

Branch Support

103967

Installing Blower Assembly

Note:

If you are using a mantel with your heater, use the following

instructions. If your heater is built-in, see For Built-In Installation

on page 3.

1. Install snap bushings found in hardware kit into both holes

in rear of valve cover shield.

2. Make sure the wire harness is firmly connected to the termi-

nals on the blower bracket assembly.

3. Note the wire locations on back of AUTO/OFF/ON switch.

The terminals on back of switch are numbered 1, 2, and 3.

Carefully remove red wire from terminal 3 and blue wire from

terminal 1. Black wire can remain on middle terminal 2 (see

Figure 4).

4. Carefully disconnect green and white wires at their insulated

connectors.

5. In top of the heater cabinet, locate the four mounting holes on the

outercasing.Alignthesefourholeswiththoseontheblowerbracket

assembly.Attachblowerbracketassemblytotheouter casingwith

4 #10 screws provided (see Figure 4).

6. Route the wire harness through the hole in left side of baffle.

Pull wire harness through lower opening on the side of the

valve shield. (see Figure 4).

7. Insert the 4 wire harness into one of the round holes in the rear

of the valve cover shield and through the rectangular hole in

the front of shield (see Figure 4).

8. Reconnect red wire to switch position 3. Reconnect blue wire to

switch position 1. Reconnect green and white wires.

9. Install the switch plate on the valve cover shield with 2 #10

screws provided (see Figure 5). Route power cord out of the

cabinet by inserting it through the bushing on the outer casing

(see Figure 4). Plug fan kit into 120-Volt grounded power sup-

ply and test operation.

Note:

When switch is in the AUTO

position, the fan will start after the heater has run for a few

moments. The fan will continue to run for several moments

after the heater has been turned off. When switch is in the ON

position, the fan will run until turned to OFF.

10. Reinstall upper louver assembly (see Figure 2 or 3, page 1)

and branch support. Close lower louver door.

11. Carefully reinstall log set per instructions in your fireplace

owner’s manual. Reinstall screen before relighting fireplace.

CAUTION: Label all wires prior to disconnection

when servicing controls. Wiring errors can cause

improper and dangerous operation.

CAUTION:Verifyproperoperationafterservicing.

Figure 4 - Installing Blower Bracket Assembly

Valve Cover

Shield

Switch Plate Screw

Figure 5 - Installing Switch Plate to Valve Cover Shield

Wire Harness

Blower Bracket

Assembly

Power

Cord

Wire

Harness

Switch

Baffle

Wiring Routing

Hole in Baffle

Switch

Plate

BlueRed

Valve Cover

Shield

Snap

Bushing

Screw

103967

Continued

1. Install a snap bushing found in hardware kit into

oneof the holes found rear of valvecovershield.

The other hole is for a strain relief clamp (not

supplied) to secure incoming electrical supply.

2. Follow steps 2 through 6 in Installing Blower

Assembly, page 2.

3. A licensed electrician must follow the wiring dia-

gram to connect incoming electrical supply to fan

kit wiring harness.

4. Plug power cord to the outlet receptacle (not

provided) as shown in Figure 6. Wind the extra

cable in power cord and tie it up with the plastic

wire strap (see Figure 6). Set the cable bundle

between the burner bracket and outer casing,

away from the burner.

5. Test to make sure the blower is working properly.

6. Reinstall upper louver assembly (see Figure 2

or 3, page 1) and close lower louver.

7. Carefully reinstall log set per instructions in your

fireplace owner’s manual. Reinstall screen be-

fore relighting fireplace.

Figure 6 - Installing Blower Bracket Assembly

For Built-In Installation

WARNING: A licensed electrician

mustconnectthewiringharnesstoelec-

trical supply following all local codes.

Electrician must provide a clamp on the

box cover to secure the wiring. Wiring

shouldbe routedthroughthe bushingin

the hole on the outer casing of heater.

Blower Bracket

Assembly

Screw Wire

Harness

Power

Cord

Plastic

Wire

Strap

Wire

Harness

Switch

Plate

Switch

Clamp Connector

(not included)

Blue Red

Outlet

Receptacle

(Not Supplied)

EXTENSION CORD

Use extension cord if needed. The cord must have a

three-prong, grounding plug and a three-hole recep-

tacle. Make sure cord is in good shape. It must be

heavyenoughtocarrythecurrentneeded.Anunder-

sized cord will cause a drop in line voltage. This will

resultinlossofpowerandoverheating.UseaNo.16

AWG cord for lengths less than 50 feet.

Note:

Verify proper operation after servicing.

Figure 7 - Wiring Diagram For Fan Accessory Standard Installation

If any of the original wire as supplied with the appliance must be replaced, original

replacements must be used. DESA part no. 104015-01 (105°C) for power cord, and

DESA part no. 103968-01 (200°C) for wire harness.

101584-06

120 Vac. 60 Hz. .30 Amps

DESA International, Bowling Green, KY

Red Red

Fan Switch

(Auto/Off/On)

Blue

Thermostat

Switch

(N.O.)

Green

White Green

White

110/115

V.A.C. Blower

Motor

Black

Off 1

Auto

WARNING: Never attempt to service heater while it is plugged in,

operating, or hot. Burns and electrical shock could result. Only a

qualified service person should service or repair heater.

WARNING: Label all wires prior to disconnection when servicing

controls. Wiring errors can cause improper and dangerous opera-

tion. Verify proper operation after servicing.

WARNING:

Electrical Grounding Instructions:

This appliance is equipped with a three-

prong (grounding) plug for your protec-

tionagainstshockhazardandshouldbe

pluggeddirectlyintoaproperlygrounded

three-prong receptacle.

103967-01

Rev. C

04/00

2701 Industrial Drive

P.O. Box 90004

Bowling Green, KY 42102-9004

Technical Service Department 1-800-323-5190

Parts Department 1-800-972-7879

www.desatech.com

INTERNATIONAL

OFF

OPERATING FAN

Thisblower has three settings: ON, OFF, andAUTO.IntheON

position,theblowerwilloperateconstantly.IntheOFFposition,

the blower will not operate. In the AUTO position, the blower

will start when the thermostat senses a sufficient increase in

firebox temperature.

Note:

Your fireplace andthermostatblowerwill notturnonand

off at the same time. The fireplace may run for several minutes

beforetheblowerturnson.Aftertheheatermodulatestothepilot

position,theblowerwillcontinuetorun.Theblowerwillshutoff

after the firebox temperature decreases.

Note:

It is safe to operate fireplace with blower turned off.

However, the blower helps distribute heated air from the fire-

place.

Figure 8 - Auto/Off/On Switch

Auto/Off/On Switch

103967 01

NOT A UPC

Dieses Handbuch passt für folgende Modelle

Andere Desa Thermostat Handbücher

Desa

Desa PP100 Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Honeywell

Honeywell T6811 Bedienungsanleitung