www.desatech.com 119355-01A2
Figure 5 - Wiring Diagram For Blower
Accessory
WALL MOUNTING INSTRUCTIONS
FOR MODELS WITH MOUNTING
BRACKET
1. Mount heater to wall by following steps un-
der Installing to Wall in owner’s manual.
2. Plug power cord of blower into grounded
outlet.
LIMITED WARRANTY
DESA Heating Products warrants this product to be free from defects in materials and workmanship for
one(1)yearfromthedateofrstpurchase,providedthattheproducthasbeenproperlyoperated.
This warranty is extended only to the original purchaser. DESA Heating Products shall either replace the
product or refund the full purchase price. Warranty service is available only through authorized dealers.
Thiswarrantydoesnotapplytothefailureofanypartresultingfromaccidentormisusebytheowner,
nor does it apply to use in commercial applications.
To the full extent allowed by the law of the jurisdiction that governs the sale of the product: this express
warranty excludes any and all other expressed warranties. The above expressed warranty is in lieu of
all other warranties either expressed or implied including but not limited to the implied warranties of
merchantabilityandtnessforaparticularpurpose.DESAHeatingProducts’liabilityisherebylimitedto
thepurchasepriceoftheproduct,andDESAHeatingProducts’shallnotbeliableforanyotherdamages
whatsoeverincludingindirect,incidental,orconsequentialdamages.
Somestatesdonotallowalimitationonhowlonganimpliedwarrantylasts,oranexclusionorlimitation
ofincidentalorconsequentialdamages,sotheabovelimitationonimpliedwarranties,orexclusionor
limitation on damages may not apply to you.
Thiswarrantygivesyouspeciclegalrights,andyoumayalsohaveotherrightswhichvaryfromstatetostate.
For information about this warranty write:
2701 Industrial Drive
P.O. Box 90004
BowlingGreen,KY42102-9004,USA
Thermostat
Sensor
Switch
Green
White
Green
White
110/115
V.A.C. Blower
Motor
Black Black
6. Position blower assembly on cabinet back
panelwithinletoverslotsinpanel,andout-
let pointed towards front (see Figure 4).
7. While holding blower against inside of
back panel, attach blower with two #10
screws (supplied) as shown in Figure 4.
8. Attachblowerswitchtoupperbafewith
two #8 screws (see Figure 4).
9. Reattach front panel to heater using four
painted screws.
10. Complete installation of heater by follow-
ing the steps in your owner’s manual.
Figure 4 - Front of Heater, Attaching Blower
Screws
Power Cord Placement
Blower
Slots
Blower
Outlet
Back
Panel
Bafe
EXTENSION CORD
Use extension cord if needed. The cord must
have a three-prong, grounding plug and a
three-hole receptacle. Make sure cord is in
good shape. It must be heavy enough to carry
the current needed. An undersized cord will
cause a drop in line voltage. This will result in
loss of power and overheating. Use a No. 16
AWG cord for lengths less than 50 feet.
CAUTION: Verify proper op-
eration after servicing.
OPERATING BLOWER
The blower is connected to a thermostat.
Whenunitheatsup,theblowerwilloperate.
A few minutes after unit cycles off or is turned
off,blowerwillshutoff.Blowerwillcycleon
and off in this manner. Note: If you have a
heater with a thermostat, the heater and
blower will not turn off and on at exactly the
same time. Blower cycle times will vary with
heat setting selected.
Fan
Switch
