Dexter Laundry COIN COMPACT DRYER Bedienungsanleitung

8514-046-001F

July 2013

OPERATOR’S MANUAL

for COIN COMPACT DRYER

The dryer ust not be stored or installed where it will be exposed to water and/or weather.

WARNING: For your safety the information in this manual must e followed to

minimize the risk of fire or explosion or to prevent property damage, personal

injury or death.

-Do not store or use gasoline or other flamma le vapors and liquids in the vicinity of

this or any other appliance.

-WHAT TO DO IF YOU SMELL GAS

-Do not try to light any appliance.

-Do not touch any electrical switch: do not use any telephone in your uilding.

-Clear the room, uilding or area of all occupants.

-Immediately call your gas supplier from a neigh or’s telephone. Follow the

gas supplier’s instructions.

-If you cannot reach your gas supplier, call the fire department.

Installation and service must e performed y a qualified installer, service agency or

the gas supplier.

You, the purchaser, ust post in a pro inent location instructions to be followed in the event the user s ells

gas. Consult your local gas supplier for procedure to be followed if the odor of gas is present.

Post the following

“For Your Safety”

caution in a pro inent location:

FOR YOUR SAFETY

Do not store or use gasoline or other fla able vapors or liquids in the vicinity of this or any other appliance.

FOR YOUR SAFETY

THIS MACHINE IS FOR DRYING ONLY FABRICS CLEANED IN WATER.

avoid possibility of fire, including spontaneous co bustion, do not dry oiled floor ops, ite s

containing foa rubber or si ilarly textured rubberlike aterials or any aterial on which you

have used a cleaning solvent or which contains fla able liquids or solids (such as gasoline,

kerosene, waxes, etc.)

It is i portant that you read this Manual and retain it for future reference.

For service or replace ent parts, contact the distributor in your area or:

Dexter Laundry, Inc

2211 W. Gri es

Fairfield, Iowa 52556, USA

French Language Warnings

AVERTISSEMENT. Assurez-vous de ien suivre les instructions données dans cette

notice pour réduire au minimum le risque d’incendie ou d’explosion ou pour éviter

tout dommage matériel, toute lessure ou la mort.

Ne pas entreposer ni utiliser d’essence ni d’autres vapeurs ou liquides infla ables dans

le voisinage de cet appareil ou de tout autre appareil.

I. QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:

· Ne pas tenter d’allu er d’appareil.

· Ne touchez à aucun interrupteur. Ne pas vous servir des téléphones se trouvant

dans le bâti ent oú vous vous trouvez.

· Évacuez la pièce, le bâti ent ou la zone.

· Appelez i édiate ent votre fournisseour de gaz depuis un voisin. Suivez les

instructions du fournisseur.

· Si vous ne pouvez rejoindre le founisseur de gaz, appelez le service des

incendies.

L’installation et l’entretien doivent être assurés par un installateur ou un service d’entretien

qualifié ou par le fournisseur de gaz.

POUR VOTRE SÉCURITÉ

Ne pas enteposer ni utiliser d’essence ni d’autres

vapeurs ou liquides infla ables dan le voisinage

de cet appareil ou de tout autre appareil.

TABLE OF CONTENTS

Page No.

Warnings about use and operation ...................................................................................... 3

Installation Instructions ................................................................................................5, 6, 7

Dryer Shutdown .................................................................................................................10

Operating Instructions.........................................................................................................11

Preventative Maintenance Instructions................................................................................16

ILLUSTRATIONS

Figure 1 - Dryer Di ensions .................................................................................................4

Figure 2 - Vertical Clearance Di ensions ............................................................................6

Figure 3 - Dryer Exhausting ..................................................................................................9

WARNINGS ABOUT USE AND OPERATION

It is ABSOLUTELY ESSENTIAL that the dryer be grounded to a known earth (zero)

ground. This is not only for personal safety, but is necessary for proper operation.

KEEP SHIELDS, GUARDS AND COVERS IN PLACE. These safety devices are

provided to protect everyone fro injury.

A DRYER SHOULD BE CONNECTED TO POWER FOR THREE (3) MINUTES

before it is operated or before a progra change is ade. Operation or progra changes, which

occur during this "power up" period, are subject to loss in case of power interruption. After the

initial three inutes, all progra ed data is protected fro power interruptions of any length

and the custo er's individual cycle is protected up to 3 seconds. This is done without batteries.

LEAVE THE ELECTRICAL POWER TO THE DRYER ON AT ALL TIMES except

when necessary for service or other si ilar activities. The hour eter function adds only full

hours to its reading. If the power is shut off every night, any fraction of an hour of ti e that is on

the achine at that ti e will be lost. Turning the power off every night could also have so e

effect on the long-ter life of the e ory after a nu ber of years. Turning power off

occasionally won’t affect the unit.

THIS DRYER IS EQUIPPED WITH A MANUALLY RESETTABLE OVER-

TEMPERATURE THERMOSTAT located on the end of the burner housing below the gas valve.

Should the dryer cease to heat, reset the ther ostat by inserting a wooden (nonconductive)

pencil or dowel through the guide bushing in the cover. Should the ther ostat continue to trip,

the dryer ust be inspected by a qualified service person.

CHECK THIS THERMOSTAT WHEN INSTALLING DRYER to assure it is not

tripped. I pacts, such as rough handling in ship ent, ay trip the ther ostat. It ay be reset by

inserting a wooden (nonconductive) pencil or dowel through the guide bushing in the cover.

INSTALLATION AND OPERATING INSTRUCTIONS

This dryer may have een supplied as part of a washer/dryer stacked

appliance. If so, refer to the washer instructions for uncrating and hard

mounting the stacked unit to a concrete floor and o serve the dryer clearances

listed elow.

UNCRATING AND PLACING DRYER (Stand alone dryer unit):

Tools Required: ½ in. hex socket and ratchet driver, wood block 4 in. or 5 in. (102-127 )

thick, a knife and a groove joint pliers, which will open to 1 3/8 in. (35 ).

1. Re ove and discard stretch-wrap, posts, cap and inner packing.

2. The crate base is attached to the dryer by (4) cap screws driven upward fro below the crate

base. Re ove crate base fro dryer, by tipping dryer sidewise and place block under crate base

rail in center of dryer. Using a ratchet and ½ in. hex socket, re ove and discard (2) crating bolts

fro side, which is raised. Re ove block fro under crate base. Repeat for other side.

3. Install the leveling legs, which are shipped inside the dryer dru . Using a walking otion,

ove dryer sideways about 6 in. (152 ) off crate base. Tip dryer up and place block under

edge of dryer. Thread two leveling legs about two-thirds into the T-nuts on the base fro which

the crating bolts were re oved. Re ove block fro under dryer.

With a walking otion ove dryer co pletely off crate base. Discard crate base.

Tip dryer sidewise, as previously done, and place block under edge of dryer on raised side.

Thread leveling legs into nuts as was done for the first side.

Slide unit into position where it will be installed. Adjust leveling legs, using the groove joint

pliers, to level and align dryer with adjacent units.

DRYER INSTALLATION

1. CODE CONFORMITY: All co ercial dryer installations ust confor to the local and

national codes for the location of installation.

2. INSTALLATION CLEARANCES: This unit ay be installed at the following alcove

clearance.

I. Left Side 0

II. Right Side 0

III. Back 18 in. (457 ) clearance is necessary behind the otors to allow

servicing and aintenance.

IV. Front 48 in. (1220 ) to allow use of dryer.

V. Top Refer to figure labeled “Vertical Clearance Di ensions”.

AB. 0 clearance is allowable at the top; 4 in. (102 ) back fro the

front. However 1/4 in. (6 ) clearance should be allowed in case the

dryer needs oving.

C. 10 in. (254 ) clearance is required fro top at all other points.

VI. Floor If used as a stand alone dryer, this unit is intended to be installed upon an

elevated surface. The surface ust be of suitable strength to support 450

pounds (205 kg), and the dryer should be bolted or anchored to prevent

horizontal ove ent. The dryer ay be installed upon a co bustible

surface.

Refer to the label attached to the Belt Guard on the rear of the dryer for other installation

infor ation and start-up instructions.

3. MAKE-UP AIR. Adequate ake-up air, 440 CFM (12.5

/ in.), ust be supplied to

replace air exhausted by dryers on all types of installations. Provide a ini u of 1 sq. ft.

(.14

) ake-up air opening to outside for each dryer. This is a net require ent of effective area.

Screens, grills or louvers, which will restrict the flow of air, ust be considered. Consult the

supplier to deter ine the free area equivalent for the grill being used.

The source of ake-up air should be located sufficiently away fro the dryers to allow an even

airflow to the air intakes of all dryers. Multiple openings should be provided.

NOTE: The following considerations ust be observed for gas dryer installation where dry

cleaners are installed.

The sources of all ake-up air and roo ventilation air ove ent to all dryers ust be located

away fro any dry cleaners. This is necessary so that solvent vapors will not be drawn into the

dryer inlet ducts. Dry cleaner solvent vapors will deco pose in contact with open fla e such as

the gas fla e present in clothes dryers. The deco position products are highly corrosive and will

cause da age to the dryer(s) ducts and clothes loads.

4. ELECTRICAL REQUIREMENTS. The electrical power require ents necessary to operate

the unit satisfactorily are listed on the serial plate located on the back panel of each dryer. The

electrical connection should be ade to the ter inal board, on the rear of the unit in the upper

control box using copper conductors of 15A ini u capacity. It is absolutely necessary that the

dryer be grounded to a known (earth) ground.

The installation ust eet the National Electrical Require ents of the country of installation.

Individual 15A circuit breakers for each dryer are required. The installer ust provide a

disconnect switch which will interrupt both lines. It ay be a local or national require ent to

provide an electrical interruption switch visible and accessible fro the roo in which the dryer is

installed. The wiring diagra is located on the belt guard on the back of the dryer.

5. GAS REQUIREMENTS. The co plete gas require ents necessary to operate the dryer

satisfactorily are listed on the serial plate located on the back panel of the dryer.

The inlet gas connection to the unit is ½ in. NPT pipe thread. However, the size of the piping to

supply the dryer should be deter ined by reference to national installation practice and

consultation with the local gas supplier.

A joint co pound resistant to all fuel gases ust be e ployed in aking threaded pipe

connections.

A drip tee should be provided in the unit gas piping to catch dirt and other foreign articles.

All pipe connections should be checked for leakage with soap solution. Never check with an

open fla e.

CAUTION: The dryer and its individual shutoff valve ust be disconnected fro the gas supply

piping syste during any pressure testing of that syste at test pressures in excess of ½ psig

(35 bar). The dryer ust be isolated fro the gas supply piping syste by closing its individual

anual shutoff valve during any pressure testing of the gas supply piping syste at test pressures

equal to or less than ½ psig (35 bar).

6. EXHAUST INSTALLATION. (Refer to Figure 3 at the end of section 6.) Exhausting of the

dryer(s) should be planned and constructed so that no air restrictions occur. Any restriction due to

pipe size or type of installation can cause slow drying ti e, excessive heat, and lint in the roo .

Fro an operational standpoint, incorrect or inadequate exhausting can cause a cycling of the

high li it ther ostat, which shuts off the ain burners and results in inefficient drying.

Individual exhausting of the dryers is reco ended. All heat, oisture, and lint should be

exhausted outside by attaching a pipe of the proper dia eter to the dryer adapter collars and

extending it out through an outside wall. This pipe ust be very s ooth on the inside, as rough

surfaces tend to collect lint, which will eventually clog the duct and prevent the dryer fro

exhausting properly. All elbows ust be s ooth on the inside. All joints ust be ade so the

exhaust end of one pipe is inside the next one downstrea . The addition of an exhaust pipe tends

to reduce the a ount of air the blower can exhaust. This does not affect the dryer operation if

held within practical li its. For the ost efficient operation, it is reco ended that no ore than

14 ft. (4.25 ) of straight 6 in. (152 ) dia eter pipe with two right angle elbows be used for

each cylinder.

If the exhaust pipe passes through a wall, a etal sleeve of slightly larger dia eter should be set

in the wall and the exhaust pipe passed through this sleeve. This practice is required by so e

local codes and is reco ended in all cases to protect the wall.

This type of installation should have a eans provided to prevent rain and high winds fro

entering the exhaust when the dryer is not in use. A hood with a hinged da per can be used for

this purpose. Another ethod would be to point the outlet end of the pipe downward to prevent

entrance of wind and rain. In either case, the outlet should be kept clear, by at least 24 in. (610

) of any objects, which would cause air restriction.

Provide a screen or grill over the ter ination of the exhaust or flue outlet such as will prevent the

entry of a ball of 5/8 (16 ) in dia eter while the achine is not operating but will allow entry

of a ball 1/4 (6 ) in dia eter while operating.

When exhausting a dryer straight up through a roof, the overall length of the duct has the sa e

li its as exhausting through a wall. A rain cap ust be placed on top of the exhaust and ust be

of such a type as to be free fro clogging. The type using a cone shaped “roof” over the pipe is

suitable for this application.

Exhausting the dryer into a chi ney or under a building is not per itted. In either case there is a

danger of lint buildup, which can be highly co bustible.

Installation of several dryers, where a ain discharge duct is necessary, will need the following

considerations for installation (see Figure 3). Individual 6 in. (152 ) exhaust ducts fro the

each dryer should enter ain discharge duct at a 45-degree angle in the direction of discharge

airflow.

NOTE: Never install the individual ducts at a right angle into the ain discharge duct.

The individual ducts fro the dryers can enter at the sides or botto of the ain discharge

duct. Figure 3 indicates the various round ain duct dia eters to use with the individual

dryer ducts. The ain duct can be rectangular or round, provided adequate airflow is

aintained. The total exhausting ( ain discharge duct plus duct outlet fro the dryer)

should not exceed the equivalent of 14 ft. (4.5 ) and two elbows. The dia eter of the

ain discharge duct at the last dryer ust be aintained to exhaust end.

NOTE: A s all dia eter duct will restrict airflow; a large dia eter duct will reduce air velocity

- both contributing to lint build up. An inspection door should be provided for periodic clean out

of the ain duct.

7. DRYER IGNITION (SOLID STATE IGNITION). The solid-state ignition syste lights the

ain burner gas by spark. The gas is ignited and burns only when the gas-valve relay (in the

electronic controller) calls for heat. The procedure for first-ti e starting of a dryer is as follows:

A. First, review and co ply with the “WARNINGS ABOUT USE AND OPERATION” found

on the inside front cover of this anual. Be sure the electrical power supply is connected

correctly. The dryer MUST be properly grounded.

B. Make sure all gas supply lines are purged of air. Close the ain gas shut-off valve and wait

for five inutes before turning the valve back on.

C. Turn on the ain electrical power switch. The dryer ay be started by following the

“OPERATING INSTRUCTIONS” found later in this anual.

D. Natural gas and liquefied petroleu gas fired dryers both operate in the sa e anner. When

the gas-valve relay contacts are closed (indicating a de and for heat), the solid-state ignition

control will auto atically supply energy to the redundant gas valve. Spark will continue until a

fla e is detected by the sensing probe, but not longer than 10 seconds. If the gas fails to ignite

within 10 seconds, the gas will shut off for 15 seconds. The control will atte pt to ignite two

ore ti es in a si ilar anner. If the gas fails to ignite after three tries, the gas valve closes and

the syste will “lock out”. No further atte pts at ignition will be perfor ed auto atically. It is

then necessary to interrupt electrical power to the ignition syste before aking another atte pt

at igniting the burners. This can be done by opening the dryer door, allowing the dryer to co e to

a stop for 15 seconds, closing the door, and pushing the Start button. The dryer will then repeat

the ignition trial cycle.

DRYER SHUTDOWN

To render the dryer inoperative, turn off the ain gas shut-off valve and disconnect electrical

power to the dryer.

Inhaltsverzeichnis

Andere Dexter Laundry Trockner Handbücher

Dexter Laundry

Dexter Laundry T-30 Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-50X2 Administratorhandbuch

Dexter Laundry

Dexter Laundry V Series Handbuch

Dexter Laundry

Dexter Laundry C Series Kurzanleitung

Dexter Laundry

Dexter Laundry T-30X2 Bedienungsanleitung

Dexter Laundry

Dexter Laundry DRC55 Series Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-80 Bedienungsanleitung

Dexter Laundry

Dexter Laundry C Series Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-30 Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-20X2 Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-30 Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-20 SWD Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-50X2 Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-30X2 Montageanleitung

Dexter Laundry

Dexter Laundry T-30 Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-20SWD Montageanleitung

Dexter Laundry

Dexter Laundry DDAD30KC Series Bedienungsanleitung

Dexter Laundry

Dexter Laundry STACK DRYER Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-50X2 Leitfaden

Dexter Laundry

Dexter Laundry DTCH30 series Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-30 SWD Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-30SWD Bedienungsanleitung

Dexter Laundry

Dexter Laundry B-Series Bedienungsanleitung

Dexter Laundry

Dexter Laundry DC50X2 Bedienungsanleitung

Beliebte Trockner Handbücher anderer Marken

Bosch

Bosch WTA79200GB Bedienungsanleitung

Amana

Amana W10233410A Bedienungsanleitung

Asko

Asko T760 Bedienungsanleitung

Bosch

Bosch Logixx 10 WTB76556GB Technisches Datenblatt

Electrolux

Electrolux EW2H328R2 Bedienungsanleitung

Beko

Beko DS8433RX1M Bedienungsanleitung

Dawlance

Dawlance Spinner DS 6000 C Bedienungsanleitung

Electrolux

Electrolux TP5080TW Bedienungsanleitung

AEG

AEG TR838P4OB Bedienungsanleitung

Indesit

Indesit IDV 75 Bedienungsanleitung

Infiniton

Infiniton SD-DG85C Bedienungsanleitung

BOMANN

BOMANN WT 5019 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Bedienungsanleitung

Asko

Asko T793C Bedienungsanleitung

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Bedienungsanleitung

Frigidaire

Frigidaire CAQE7077KW0 Betriebsanleitung

Bosch

Bosch WTX8HKM9SN Bedienungsanleitung

Sharp

Sharp KD-NHH9S7GW2-PL Bedienungsanleitung