Dexter Laundry DRC55 Series Bedienungsanleitung

INSTRUCTION MANUAL

for

DRC55 Series Dryers (25Kg Capacity)

The dryer must not be stored or installed where it will be exposed to water and/or weather and is

suitable for use in room temperatures between 5C and 45C.

WARNING: For your safety the information in this manual must be followed to minimize

the risk of fire or explosion or to prevent property damage, personal injury or loss of life.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or

any other appliance.

- WHAT TO DO IF YOU SMELL GAS

- Do not try to light any appliance.

- Do not touch any electrical switch; do not use any phone in your building.

- Clear the room, building or area of all occupants.

- Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s

instructions.

- If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency or the

gas supplier.

You, the purchaser, must post in a prominent location instructions to be followed in the

event the user smells gas. Consult your local gas supplier for procedure to be followed if

the odor of gas is present.

Post the following “For Your Safety” caution in a prominent location:

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or

any other appliance or machine.

It is important that you read this Manual and retain it for future reference.

For service or replacement parts, contact the Dexter Distributor in your area or the manufacturer.

The Dexter Company

2211 W. Grimes

Fairfield, Iowa 52556, USA 8514-027-005

-2-

TABLE OF CONTENTS

Page No.

Dryer Dimensions (Figure 1).............................................................................................. 3

Uncrating .......................................................................................................................... 4

Field Assembly.................................................................................................................. 4

Dryer Installation............................................................................................................... 5

Dryer Exhaust System (Figure 2)........................................................................................6, 7

Dryer Shutdown.................................................................................................................10

Operating Instructions.........................................................................................................10

Preventative Maintenance...................................................................................................14

Schematic/Wiring Diagrams.................................................................................................17, 18

WARNINGS ABOUT USE AND OPERATION

KEEP SHIELDS, GUARDS AND COVERS IN PLACE. These safety devices are

provided to protect everyone from injury.

A DRYER SHOULD BE CONNECTED TO POWER FOR THREE (3) MINUTES

before it is operated or before a program change in made. Operation or program changes which

occur during this “power up” period are subject to loss in case of power interruption. After the

initial three minutes, all programmed data is protected from power interruptions of any length and

the customer’s individual cycle is protected up to 3 seconds. This is done without batteries.

LEAVE THE ELECTRICAL POWER TO THE DRYER ON AT ALL TIMES except

when necessary for service or other similar activities. The hour meter function adds only full

hours to its reading. If the power is shut off every night, any fraction of an hour of time that is on

the machine at that time will be lost. Turning the power off every night could also have some

effect on the long term life of the memory after a number of years. Turning power off

occasionally won’t affect the unit.

From a safety aspect shutting off the gas supply at night would be better than shutting off

the electrical power.

THIS DRYER IS EQUIPPED WITH A MANUALLY RESETTABLE OVER-

TEMPERATURE THERMOSTAT located on the back side of the return air boot beside the

burner housing. Should the dryer cease to heat, reset the thermostat by inserting a wooden

(nonconductive) pencil or dowel through the guide bushing in the cover. Should the thermostat

continue to trip, the dryer must be inspected by a qualified service person.

CHECK THE THERMOSTAT WHEN INSTALLING DRYER to assure it is not

tripped. Impacts, such as rough handling in shipment, may trip the thermostat. It may be reset by

inserting a wooden (nonconductive) pencil or dowel through the guide bushing in the cover.

-3-

FIGURE 1 - DRYER DIMENSIONS

-4-

INSTALLATION AND OPERATING INSTRUCTIONS

Note: Before installation, check that the local distribution conditions, nature of gas and

pressure, and the adjustment of the appliance are compatible.

UNCRATING

1. Remove cardboard container and innerpack.

2. Complete the uncrating as described in the procedure listed on the instruction sheet taped to

the loading door glass.

FIELD ASSEMBLY

For secure packaging, the dryer is shipped with the tee, one part of the heat reclaimer, inside the

lower service door.

To install:

STEP 1.

Remove 4 metal screws from the bag in coin box. Go to the rear of the dryer and remove the

tape holding the top of the vertical 8 in. (200 mm) pipe.

STEP 2.

Install the tee into both the vertical pipe and the horizontal boot. Using the four pilot holes

provided, drill 4 matching 9/64 in. (3.6 mm) diameter mounting holes; 2 holes through the boot

into the tee outlet, and 2 holes through the tee inlet into the 8 in. (200 mm) vertical pipe. Install

the 4 screws provided to secure the tee to the pipe and boot.

STEP 3.

Install your exhaust system to the tee. Tape all joints with 2 in. (50 mm) duct tape.

DRYER INSTALLATION

1. CODE CONFORMITY: All commercial dryer installations must conform to the local and

national codes for the location of installation.

2. INSTALLATION CLEARANCES: This unit may be installed at the following alcove

clearance.

I. Left Side 0 in.

II. Right Side 1 in. (25 mm)*

-5-

III. Back 18 in. (450 mm) clearance is necessary behind the belt guard to allow

servicing and maintenance.

IV. Front 48 in. (1200 mm) to allow use of dryer.

V. Top Refer to figure labeled “Vertical Clearance Dimensions”.

AB. 0 clearance at the top, 1 in. (25 mm) back from the front.

However 1/4 in. (6 mm) clearance is required to allow opening the upper

service door.

CD. A 4 in. (100 mm) clearance is required at the top between 1 in. (25

mm) and 4 in. (100 mm) from front.

E. A 10" (250 mm) clearance is required from top at all other points.

VI. Floor This unit may be installed upon a combustible floor.

*Units may be installed in direct contact with an adjacent dryer, providing allowance is made for

opening upper and lower service doors.

Refer to installation label attached to the inside surface of the upper service door of the dryer for

other installation information.

-6-

MAKE-UP AIR. Adequate make-up air (910 CFM) (26 m3/Min.) must be supplied to replace air

exhausted by dryers on all types of installations. Provide a minimum of 1.25 sq. ft.

(.12 m2) make-up air opening to the outside of each dryer. This is a net requirement of effective

area. Screens, grills or louvers which will restrict the flow of air must be considered. Consult the

supplier to determine the free area equivalent for the grill being used.

The source of make-up air should be located sufficiently away from the dryers to allow an even

air flow to the air intakes of all dryers. Multiple openings should be provided.

NOTE: The following considerations must be observed for gas dryer installations where dry

cleaners are installed. The sources of all make-up air and room ventilation air movement to all

dryers must be located away from any dry cleaners. This is necessary so that solvent vapors will

not be drawn into the dryer inlet ducts. Dry cleaner solvent vapors will decompose in contact

with open flame such as the gas flame present in clothes dryers. The decomposition products are

highly corrosive and will cause damage to the dryer(s) ducts and clothes loads.

The operation of this appliance may affect the operation of other types of gas appliances which

take their air for safe combustion from the same room. All other gas appliances should be tested

with the Dexter dryer in operation and all the windows and doors closed. If in doubt consult the

appliance manufacturer(s).

4. ELECTRICAL REQUIREMENTS: 230V~ 50Hz 1.2kW

The electrical power requirements necessary to operate the unit satisfactorily are listed on the

serial plate located on the back panel of each dryer. The electrical connection should be made to

the terminal board in the control box on the rear of the unit using a wire size adequate to handle

the amperage and voltage listed on the serial plate. It is absolutely necessary that the dryer be

grounded to a known (earth) ground.

The installation must meet the National Electrical Requirements of the country of installation.

Individual 15 A circuit breakers for each dryer are required. The installer must provide a

disconnect switch which will interrupt both lines. It may be a local or national requirement to

provide an electrical interruption switch visible and accessible from the room in which the dryer is

installed. The wiring diagram is located on the belt guard on the back of the dryer.

5. GAS REQUIREMENTS. The complete gas requirements necessary to operate the dryer

satisfactorily are listed on the serial plates located on the back panel of the dryer.

This appliance has been certified for use in the following countries: GB, IE, BE, FR, DE, NL, ES,

CH, DK and GR. This appliance is factory adjusted for G20 gas supply at either 20 or 50 mbar

supply pressure.

-7-

This appliance must be installed in accordance with the rules in force and used only in a

sufficiently ventilated space. Consult instructions before installation of this appliance.

GAS SYSTEM INFORMATION

HEAT INPUT 38.1 kW GROSS

GAS FLOW RATE 3.5 m3PER HOUR

BURNER PRESSURE 8.7 mbar G20 / 12.2 mbar G25

INJECTOR SIZE 3.9 mm

COUNTRY CATEGORY ORIFICE (mm)

2ND / 3RD FAMILY REGULATOR. SETTING mBAR

2ND / 3RD FAMILY

GB IE IT CH

ES II 2H3+ 3.9 / 2.4 8.7 / ANNULLED

FR II

Er3+(29/37) 3.9 / 2.4 8.7 (G20),12.2 (G25) /

ANNULLED

BE I 2E(S)B 3.9 / NA 8.7 (G20),12.2 (G25) / NA

DE II 2EB/P 3.9 / 2.4 8.7 / 22.4

NL II 2L3B/P(50) 3.9 / 2.4 12.2 / 22.4

DK GR II 2H3B/P 3.9 / 2.4 8.7 / 22.4

The inlet gas connection to the unit is ISO 7-RC 3/4 thread. The connection to the appliance

shall be made with a flexible hose suitable for the appliance category in accordance with national

installation regulations. The size of the piping to supply the dryer should be determined by

reference to national installation practice and consultation with the local gas supplier.

A joint compound resistant to all fuel gases must be employed in making threaded pipe

connections.

A drip tee is to be provided in the gas piping entering the unit to catch dirt and other foreign

articles.

All pipe connections should be checked for leakage with a suitable leak detection fluid. Never

check with an open flame.

Note: There are two 9 mm pressure taps, one at the inlet side, one at the outlet side of the gas

valve, for use if it is necessary to check either pressure.

-8-

CONVERSION TO LP GAS (G30):

Conversion of this appliance to LP gas requires a kit supplied by the Dexter Company. Please

contact your local Dexter distributor to purchase the proper conversion kit. Be sure to keep the

instructions provided with the kit along with these instructions for reference.

PRESSURE REGULATOR ADJUSTMENT

Adjustments should be made by qualified personnel only.

1. With dryer off , unscrew the outlet pressure tap on the gas control valve a half turn and

slip pressure gauge tube over nipple. Ensure that screw is retightened after the regulator

is adjusted.

2. Remove regulator cap screw to expose regulator adjustment screw.

3. Start the dryer. Using a screwdriver, slowly turn the adjustment until the required

burner pressure is indicated on the pressure gauge. Turn adjustment screw clockwise to

increase and counter-clockwise to decrease gas pressure to burner. Turn dryer off.

4. Replace pressure regulator cap screw.

5. Remove pressure gauge and retighten pressure tap screw.

CAUTION: The dryer and its individual shutoff valve must be disconnected from the gas supply

piping system during any pressure testing of that system at test pressures in excess of ½ psig (35

mbar). The dryer must be isolated from the gas supply piping system by closing its individual

manual shutoff valve during any pressure testing of the gas supply piping system at test pressures

equal to or less than ½ psig (35 mbar).

6. EXHAUST INSTALLATION. (Refer to Figure 2 at the end of section 6.) Exhausting of

the dryer(s) should be planned and constructed so that no air restrictions occur. Any restriction

due to pipe size or type of installation can cause slow drying time, excessive heat, and lint in the

room.

From an operational standpoint, incorrect or inadequate exhausting can cause a cycling of the

high limit thermostat which shuts off the main burners and results in inefficient drying.

Individual exhausting of the dryers is recommended. All heat, moisture, and lint should be

exhausted outside by attaching a pipe of the proper diameter to the dryer adapter collar and

extending it out through an outside wall. This pipe must be very smooth on the inside, as rough

surfaces tend to collect lint which will eventually clog the duct and prevent the dryer from

exhausting properly. All elbows must be smooth on the inside. All joints must be made so the

exhaust end of one pipe is inside the next one downstream. The addition of an exhaust pipe tends

to reduce the amount of air the blower can exhaust. This does not affect the dryer operation if

held within practical limits. For the most efficient operation, it is recommended that no more than

20 ft. (6 m) of straight 8 in. (200 mm) diameter pipe be used with two right angle elbows. When

more than two elbows are used, 2 ft. (600 mm) of straight pipe should be removed for each

additional elbow. No more than four right angle elbows should be used to exhaust a dryer.

-9-

If the exhaust pipe passes through a wall, a metal sleeve of slightly larger diameter should be set

in the wall and the exhaust pipe passed through this sleeve. This practice is required by some

local codes and is recommended in all cases to protect the wall. This type of installation should

have a means provided to prevent rain and high winds from entering the exhaust when the dryer is

not in use. A hood with a hinged damper can be used for this purpose. Another method would

be to point the outlet end of the pipe downward to prevent entrance of wind and rain. In either

case, the outlet should be kept clear, by at least 24 in. (600 mm), of any objects which would

cause air restriction.

Provide a screen or grill over the termination of the exhaust or flue outlet such as will prevent

the entry of a ball of 16 mm in diameter while the machine is not operating but will allow entry of

a ball 6 mm in diameter while operating.

When exhausting a dryer straight up through a roof, the overall length of the duct has the same

limits as exhausting through a wall. A rain cap must be placed on top of the exhaust and must be

of such a type as to be free from clogging. The type using a cone shaped “roof” over the pipe is

suitable for this application.

Exhausting the dryer into a chimney or under a building is not permitted. In either case there is a

danger of lint buildup which can be highly combustible.

Installation of several dryers, where a main discharge duct is necessary, will need the following

considerations for installation (see Figure 2). Individual ducts from the dryers into the main

discharge duct should be at a 45 degree angle in the direction of discharge air flow.

NOTE: Never install the individual ducts at a right angle into the main discharge duct.

The individual ducts from the dryers can enter at the sides or bottom of the main discharge

duct. Figure 2 indicates the various round main duct diameters to use with the individual

-10-

dryer ducts. The main duct can be rectangular or round, provided adequate air flow is

maintained. For each individual dryer, the total exhausting (main discharge duct plus

duct outlet from the dryer) should not exceed the equivalent of 20 ft. (6 m) and two

elbows. The diameter of the main discharge duct at the last dryer must be maintained to

exhaust end.

NOTE: A small diameter duct will restrict air flow; a large diameter duct will reduce air velocity

- both contributing to lint build up. An inspection door should be provided for periodic clean-out

of the main duct.

DRYER SHUTDOWN

To render the dryer inoperative, turn off the manual gas shut-off valve and disconnect electrical

supply to the dryer.

OPERATING INSTRUCTIONS

Maximum Load Capacity: 25Kg Dry Weight

1. Deposit coins to satisfy vend price display of idle dryer. Each deposit decreases the vend price

until the display changes to show the amount of time purchased. WARM light illuminates.

2. Select drying cycle. Other cycle selections may be made now or later by pressing the

appropriate key (button).

3. Close the loading door. Press “START” and the dryer will start. The time remaining is

displayed in whole minutes (rounded up) and will count down each minute. The colon flashes on

and off indicating the timer is counting down.

4. Clothes should be removed promptly after the cycle is completed to prevent excessive

wrinkling.

Once started, the “timer” cannot be stopped. However, extra coins will be acknowledged by

adding time to the display. The dryer may be stopped by opening the loading door which

interrupts the drive motor and gas burners. Close the loading door and push “START” to restart

the dryer.

Cool-down time (owner programmable) is always part of the cycle time and is purchased by the

customer. For example, if cool-down time is 2 minutes, the last two minutes of the cycle will

have no heat.

Inhaltsverzeichnis

Andere Dexter Laundry Trockner Handbücher

Dexter Laundry

Dexter Laundry STACK DRYER Bedienungsanleitung

Dexter Laundry

Dexter Laundry C Series Bedienungsanleitung

Dexter Laundry

Dexter Laundry DDAD30HC-59 Series Dryers Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-20 SWD Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-30 SWD Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-30X2 Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-120 Kurzanleitung

Dexter Laundry

Dexter Laundry B-Series Bedienungsanleitung

Dexter Laundry

Dexter Laundry DN20X2 Leitfaden

Dexter Laundry

Dexter Laundry DL2X30Q Handbuch

Dexter Laundry

Dexter Laundry V Series Handbuch

Dexter Laundry

Dexter Laundry T-30X2 Montageanleitung

Dexter Laundry

Dexter Laundry DTCH30 series Bedienungsanleitung

Dexter Laundry

Dexter Laundry DTCH 80 V Handbuch

Dexter Laundry

Dexter Laundry T-20SWD Montageanleitung

Dexter Laundry

Dexter Laundry DDAD50KC Series Bedienungsanleitung

Dexter Laundry

Dexter Laundry DDAD30KC Series Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-80 Bedienungsanleitung

Dexter Laundry

Dexter Laundry DCT30KC Series Bedienungsanleitung

Dexter Laundry

Dexter Laundry C Series Kurzanleitung

Dexter Laundry

Dexter Laundry T-50X2 Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-30 Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-30 Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-30 Bedienungsanleitung

Beliebte Trockner Handbücher anderer Marken

Bosch

Bosch WTA79200GB Bedienungsanleitung

Amana

Amana W10233410A Bedienungsanleitung

Miele

Miele TWH 780 WP Bedienungsanleitung

Asko

Asko T760 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems 25 Series Bedienungsanleitung

Bosch

Bosch Logixx 10 WTB76556GB Technisches Datenblatt

STIEBEL ELTRON

STIEBEL ELTRON Ultronic S Bedienungsanleitung

Electrolux

Electrolux EW2H328R2 Bedienungsanleitung

Beko

Beko DS8433RX1M Bedienungsanleitung

Dawlance

Dawlance Spinner DS 6000 C Bedienungsanleitung

Electrolux

Electrolux TP5080TW Bedienungsanleitung

AEG

AEG TR838P4OB Bedienungsanleitung

Indesit

Indesit IDV 75 Bedienungsanleitung

Infiniton

Infiniton SD-DG85C Bedienungsanleitung

BOMANN

BOMANN WT 5019 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Bedienungsanleitung

Asko

Asko T793C Bedienungsanleitung

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Bedienungsanleitung