Dexter Laundry T-30 Bedienungsanleitung

8514-286-001 REV B PAGE 1

WAR

NING: For your safety the

information in this manual must be

followed to minimize the risk of fire

or explosion or to prevent property

dama e, personal injury or loss of

life.

Ne pas entreposer ni utiliser d'essence ni d'autres

apeurs ou liquides inflammables dans le oisinage

de cet appareil ou de tout autre appareil.

– QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE

GAZ:

• Ne pas tenter d'allumer d'appareil.

• Ne touchez à aucun interrupteur. Ne pas

ous ser ir des téléphones se trou ant

dans le bâtiment où ous ous trou ez.

• É acuez la pièce, le bâtiment ou la zone.

• Appelez immédiatement otre

fournisseour de gaz depuis un oisin.

Sui ez les instructions du fournisseur.

• Si ous ne pou ez rejoindre le fournisseur

de gaz, appelez le ser ice des incendies.

– L'installation et l'entretien doi ent être assurés par

un installateur ou un ser ice d'entretien qualifié

POUR VOTRE SÉCURITÉ

Ne pas enteposer ni utiliser d'essence ni d'autres

vapeurs ou liquides inflammables dans le voisinage

de cet appareil ou de tout autre appareil.

You, the purchaser, must post in a prominent loca-

tion instructions to be followed in the event the user

smells gas. Consult your local gas supplier for

procedure to be followed if the odor of gas is

present.

AVERTISSEMENT. Assurez

vouz

de bien suivre les instructions

données dans cette notice pour

réduire au minimum le risque

d incendie ou d explosion ou pour

éviter tout dommage matérial,

toute blessure ou la mort.

COMMERCIAL DRYER

MODEL T-30 SWD VENDED

C-SERIES CONTROL, NATURAL GAS/LP HEATED

OPERATOR’S MANUAL

INSTALLATION & OPERATION INSTRUCTIONS

The dryer must not be stored or installed where it will be exposed to water and/or weather.

Post the following “For Your Safety” caution in a

prominent location:

It is important that you read this Manual and retain it

for future reference. For ser ice or replacement parts,

contact the distributor in your area or the

manufacturer.

Dexter Laundry, Inc.

2211 W. Grimes

Fairfield, Iowa 52556

Do not store or use gasoline or other flammable

apors and liquids in the icinity of this or any

other appliance.

– WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do

not use any phone in your building.

• Clear the room, building or area of all

occupants.

• Immediately call your gas supplier from

a neighbor’s phone. Follow the gas

supplier’s instructions.

• If you cannot reach your gas supplier,

call the fire department.

– Installation and ser ice must be performed by

a qualified installer, ser ice agency or the

gas supplier.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable

vapors or liquids in the vicinity of this or any other

appliance.

8514-286-001 REV B PAGE 2

TABLE OF CONTENTS

Page No.

Warnings about use and operation 2

Dryer Specifications 3

Dryer Dimensions 5

Installation Instructions 6-10

Dryer Shutdown 10

Operating Instructions 11

Programming the Dryer Control 12-22

Ser icing and Troubleshooting 23

Pre entati e Maintenance Instructions 24

WARNINGS ABOUT USE AND OPERATION

DO NOT MODIFY THIS APPLIANCE. KEEP SHIELDS, GUARDS AND COVERS IN PLACE. These safety

de ices are pro ided to protect e eryone from injury.

It is ABSOLUTELY ESSENTIAL that the dryer be grounded to a known earth (zero) ground in accordance with

local codes or, in the absence of local codes, with the latest editions of the National Electric Code, ANSI//NFPA 70 or

Standard CSA C22.1 Canadian Electrical Code Part 1. This is not only for personal safety, but is necessary for

proper operation of the controller. Failure to do so will oid the warranty of the controller.

A DRYER SHOULD BE CONNECTED TO POWER FOR THREE (3) MINUTES before it is operated or

before a program change is made. Operation or program changes, which occur during this "power up" period, are

subject to loss in case of power interruption. After the initial three minutes, all programmed data is protected

from power interruptions of any length and the customer's indi idual cycle is protected up to 3 seconds. This is

done without batteries.

LEAVE THE ELECTRICAL POWER TO THE DRYER ON AT ALL TIMES except when necessary for ser ice

or other similar acti ities. The hour meter function adds only full hours to its reading. If the power is shut off e ery night,

any fraction of an hour of time that is on the machine at that time will be lost. Turning the power off e ery night

could also ha e some effect on the long-term life of the memory after a number of years. Turning power off

occasionally won’t affect the unit.

THIS DRYER IS EQUIPPED WITH AN OVER-TEMPERATURE THERMOSTAT located on the end of

the burner housing abo e the gas al e. Should the dryer cease to operate, refer to your “Ser ice Procedure and

Parts Data” book for instructions.

CHECK THIS THERMOSTAT WHEN INSTALLING DRYER to assure it is not tripped. Impacts such as

rough handling in shipment, may trip the thermostat. It may be reset by inserting a wooden pencil or dowel

through the bushing in the co er.

DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE while it is in operation.

THIS APPLIANCE SHALL NOT BE USED TO DRY OFF CLOTHES CONTAINING SOLVENTS OR DRY

CLEANING FLUIDS.

8514-286-001 REV B PAGE 3

SPECIFICATIONS

30 lb. Commercial Dryer: T-30 SWD DCS030N_-15EC_X (60Hz), DCS030N_-39AC_X (50Hz)

Cabinet Height (As a stand-alone dryer) 38 7/8” 987 mm.

(Assumes minimum le eling leg adjustment)

Cabinet Height (Combo washer/dryer) 78 3/4” 2000 mm.

Cabinet Width 31 1/2” 800 mm.

Cabinet Depth 49 7/16 1256 mm.

Floor to Door Center (Stand-alone) 7” 178 mm.

Floor to Door Center (Combo) 47” 1194 mm.

Door Opening 22 5/8” 575 mm.

Dry Wt. Capacity 30 lbs. 13.6 kg.

Cylinder Diameter 30” 762 mm.

Cylinder Depth 27 1/2” 699 mm.

Cylinder Volume 11.25 cu. ft. 319 liters

Lint Screen Area 453 sq. in. 2923 sq. cm.

Gas Input (60 hz) 80,000 Btu/hr 23.4 kW or 84 MJ/Hr

Gas Input (50 hz) 74,000 Btu/hr 21.7 kW or 78 MJ/Hr

Gas Supply Connection 1/2” 12.7 mm.

Natural Gas Supply (Water Column) 5-10” 127 mm. - 254 mm.

Natural Burner Manifold Pressure

(60 hz Water Column) 3.5” .87 kPa

(50 hz Water Column) 3.4” .84 kPa

L.P. Supply (Water Column) 11 ½ -14” 292 mm. - 356 mm.

L.P. Burner Manifold Pressure

(60 hz Water Column) 11” 2.7 kPa

(50 hz Water Column) 10” 2.5 kPa

Exhaust Size 6” 152 mm.

Make-up Air 1.0 sq. ft. 929 sq. cm.

Example: 1.0 sq. ft = 1 ft. long X 1 ft. wide

Motor Size 1/2 H.P. .373 kW

Airflow (60 hz) 500 CFM 14.2 m^3/min

Airflow (50 hz) 450 CFM 12.7 m^3/min

Dryer Electrical Specifications – 208-240/60/1

Voltage/Hz/Phase 208-240V/60Hz/1Phase

Running Amps 2.5

Circuit Protection Amps 15

Wire Size 12 gauge

Electrical Ser ice 2 wire + ground

Dryer Electrical Specifications - 120/60/1

Voltage/Hz/Phase 120V/60Hz/1Phase

Running Amps 4.0

Circuit Protection Amps 15

Wire Size 12 gauge

Electrical Ser ice 2 wire + ground

Dryer Electrical Specifications - 230/50/1

Voltage/Hz/Phase 230V/50Hz/1Phase

Running Amps 5.0

Circuit Protection Amps 15

Wire Size 12 gauge

Electrical Ser ice 2 wire + ground

8514-286-001 REV B PAGE 4

Stand-alone Dryer

Shipping Weight 420 lbs. 191 kg.

Net Weight 380 lbs. 172 kg.

Clearance Behind Machines (min.) 18” 457 mm.

Combo Stack Washer/Dryer

Shipping Weight 1101 lbs. 499 kg.

Net Weight 1051 lbs. 477 kg.

Clearance Behind Machines (min.) 24” 611 mm.

8514-286-001 REV B PAGE 5

DRYER DIMENSIONS

8514-286-001 REV B PAGE 6

INSTALLATION INSTRUCTIONS

This dryer may have been supplied as part of a washer/dryer stacked appliance. If

so, refer to the washer instructions for uncrating and hard mounting the stacked

unit to a concrete floor and observe the dryer clearances listed below.

STACK WASHER / DRYER INSTALLATION (when necessary):

1. Place dryer on top of washer and align (4) mounting holes. The front (2) mounting holes are located inside

the lint compartment 5 ¾” from the front of the machine. The back (2) mounting holes are located on the

right/left side of the machine, at the base of the back panel. Remo ing the rear guard is necessary to access

the back mounting hole located opposite the duct work.

2. Use (4) supplied 5/16” x 1-1/4 dog tip bolts to secure the dryer on top of the washer.

DRYER INSTALLATION

1. CODE CONFORMITY: All commercial dryer installations must conform with local codes, or in the absence of

local codes, with the latest edition of the National Fuel Gas Code ANSI Z223.1. Canadian installations must

comply with the current Standard CAN/CGA-B149 (.1 or .2) Installation Code for Gas Burning Appliances or

Equipment, and local codes if applicable. Australian installations must meet installation requirements and pipe

sizing requirements of AS/NZA 5601. The appliance, when installed, must be electrically grounded in

accordance with the latest edition of the National Electric Code, ANSI/NFPA70, or, when installed in

Canada, with Standard CSA C22.1 Canadian Electrical Code Part 1.

2. INSTALLATION CLEARANCES: This unit may be installed at the following alco e clearances:

I. Left Side 0"

II. Right Side 0"

III. Back 18" (457 mm) (Certified for 6" (150 mm) clearance; howe er, 18" (457 mm) clearance is

necessary behind the motors to allow ser icing and maintenance.)

IV. Front 48" (1220 mm) (to allow use of dryer)

V. Top Refer to figure labeled “Vertical Clearance Dimensions”.

AB. Certification allows 0" clearance at the top 4" (100 mm) back from the front.

Howe er, a 1/4" (6 mm) clearance should be allowed in case the dryer needs to be

mo ed.

C. A 10" (250 mm) clearance is required from top at all other points.

VI. Floor If used as a stand-alone dryer, this unit is intended to be installed upon an ele ated

surface. The surface must be of suitable strength to support 450 pounds (205 kg),

and the dryer should be bolted or anchored to pre ent horizontal mo ement. This

unit may be installed upon a combustible floor.

Do not obstruct the flow of combustion and entilation air.

Maintain minimum of 1" (25 mm) clearance between duct and combustible material.

Refer to the label attached to the Belt Guard on the rear of the dryer for other installation information and

start-up instructions.

8514-286-001 REV B PAGE 7

FIGURE 2 - VERTICAL CLEARANCE DIMENSIONS

3. MAKE-UP AIR: Adequate make-up air must be supplied to replace air exhausted by dryers on all types of

installations. Refer to specifications for the minimum amount of make-up air opening to outside for each dryer.

This is a net requirement of effecti e area. Screens, grills or lou ers, which will restrict the flow of air, must be

considered. Consult the supplier to determine the free area equi alent for the grill being used. The source of

make-up air should be located sufficiently away from the dryers to allow an e en airflow to the air intakes

of all dryers. Multiple openings should be pro ided.

The sources of all make-up air and room entilation air mo ement to all dryers must be located away

from any dry cleaners. This is necessary so that sol ent apors will not be drawn into the dryer inlet

ducts. Dry cleaner sol ent apors will decompose in contact with open flame such as the gas flame present

in clothes dryers. The decomposition products are highly corrosi e and will cause damage to the dryer(s)

ducts and clothes loads.

4. ELECTRICAL REQUIREMENTS. The electrical power requirements necessary to operate the unit satisfactorily

are listed on the serial plate located on the back panel of each dryer and in the specifications section of

this manual. The electrical connections should be made to the terminal board in the electrical control box

8514-286-001 REV B PAGE 8

on the rear of the unit. It is absolutely necessary that the dryer be grounded to a known ground.

Indi idual circuit breakers for each dryer are required.

5. GAS REQUIREMENTS. The complete gas requirements necessary to operate the dryer satisfactorily are

listed on the serial plate located on the back panel of the dryer and in the specifications section of this

manual. The inlet gas connection to the unit is 1/2-inch pipe thread. Howe er, the size of the piping to supply

the dryer should be determined by reference to the National Fuel Gas Code ANSI Z223.1A and consultation

with the local gas supplier.

An indi idual gas shutoff al e is recommended for each dryer and may be required by local code (not

supplied).

A joint compound resistant to the action of liquefied petroleum gases should be employed in making pipe

connections.

A 1/8-inch NPT plugged tapping, accessible for test gage connection, must be installed immediately

upstream of the gas supply connection to the dryer.

A drip tee is pro ided in the unit gas piping to catch dirt and other foreign articles.

All pipe connections should be checked for leakage with soap solution. Ne er check with an open flame.

For altitudes abo e 2,000 feet (610m), it is necessary to de-rate the BTU input. Contact your local

distributor for instructions.

L.P. gas con ersion kits are a ailable for this dryer. Contact your local distributor.

CAUTION: The dryer must be disconnected from the gas supply piping system during any pressure

testing of that system. Do not expose the dryer’s gas control al e to testing pressure.

6. EXHAUST INSTALLATION. (Refer to Figure 3) Exhausting of the dryer(s) should be planned and

constructed so that no air restrictions occur. Any restriction due to pipe size or type of installation can

cause slow drying time, excessi e heat, and lint in the room.

From an operational standpoint, incorrect or inadequate exhausting can cause a cycling of the high limit

thermostat, which shuts off the main burners and results in inefficient drying.

The exhaust duct connection near the top of the dryer will accept a 6” (152 mm) round duct. Indi idual

exhausting of the dryers is recommended. All heat, moisture, and lint should be exhausted outside by

attaching a pipe of the proper diameter to the dryer adapter collars and extending it out through an

outside wall. This pipe must be ery smooth on the inside, as rough surfaces tend to collect lint, which

will e entually clog the duct and pre ent the dryer from exhausting properly. All elbows must be

smooth on the inside. All joints must be made so the exhaust end of one pipe is inside the next one

downstream. The addition of an exhaust pipe tends to reduce the amount of air the blower can exhaust.

This does not affect the dryer operation if held within practical limits. For the most efficient operation, it

is recommended that no more than 14 ft. (4.25 m) of straight 6 in. (152 mm) diameter pipe with two

right angle elbows be used for each cylinder.

Maintain a minimum of 1” (25mm) clearance between duct and combustible material.

If the exhaust pipe passes through a wall, a metal slee e of slightly larger diameter should be set in the

wall and the exhaust pipe passed through this slee e. This practice is required by some local codes and is

recommended in all cases to protect the wall.

This type of installation should ha e a means pro ided to pre ent rain and high winds from entering the

exhaust when the dryer is not in use. A hood with a hinged damper can be used for this purpose.

Another method would be to point the outlet end of the pipe downward to pre ent entrance of wind

and rain. In either case, the outlet should be kept clear, by at least 24 in. (610 mm) of any objects,

which would cause air restriction.

8514-286-001 REV B PAGE 9

Ne er install a protecti e screen o er the exhaust outlet.

When exhausting a dryer straight up through a roof, the o erall length of the duct has the same limits as

exhausting through a wall. A rain cap must be placed on top of the exhaust and must be of such a type

as to be free from clogging. The type using a cone shaped “roof” o er the pipe is suitable for this

application.

Exhausting the dryer into a chimney or under a building is not permitted. In either case there is a danger

of lint buildup, which can be highly combustible.

Installation of se eral dryers, where a main discharge duct is necessary, will need the following

considerations for installation (see Figure 3). Indi idual 6” (152 mm) exhaust ducts from each dryer

should enter main discharge duct at a 45-degree angle in the direction of discharge airflow.

NOTE: Ne er install the indi idual ducts at a right angle into the main discharge duct.

The indi idual ducts from the dryers can enter at the sides or bottom of the main discharge

duct. Figure 3 indicates the arious round main duct diameters to use with the indi idual

dryer ducts. The main duct can be rectangular or round, pro ided adequate airflow is

maintained. The total exhausting (main discharge duct plus duct outlet from the dryer)

should not exceed the equi alent of 14 ft. (4.25 m) and two elbows. The diameter of the

main discharge duct at the last dryer must be maintained to exhaust end.

NOTE: A small diameter duct will restrict airflow; a large diameter duct will reduce air

elocity - both contributing to lint build up. An inspection door should be pro ided for

periodic clean out of the main duct.

7. DRYER IGNITION (SOLID STATE IGNITION): The solid-state ignition system lights the main burner gas by spark.

The gas is ignited and burns only when the gas-relay (in the electronic controller) calls for heat. The procedure for

first-time starting of a dryer is as follows.

i. First re iew and comply with the "Warnings About Use and Operation" found on the inside front co er

of this manual. Be sure electrical power is connected correctly. The dryer must be properly grounded.

ii. Make sure all gas supply lines are purged of air. Close the main gas shut-off al e and wait for fi e

minutes before turning it back on.

8514-286-001 REV B PAGE 10

iii. Turn on the main electrical power switch. The dryer may be started by following the "Operating

Instructions" found later in this manual.

i . Natural gas and LPG fired dryers operate in the same manner. When the gas al e relay contacts are

closed (indicating a demand for heat), the solid-state ignition control will automatically supply energy to the

redundant gas al e. Sparking will continue until a flame is detected by the sensing probe, but not longer than

ten seconds. If the gas fails to ignite in 10 seconds, the gas al e closes and the gas system pauses to allow gas to

purge from the inside of the dryer. After the pause, the ignition control repeats the ignition trial cycle twice more.

If the gas system fails to detect ignition after the three attempts, the system will "lock out". No further attempts

will be performed automatically. To reset the ignition control electrical power to the ignition control must be

interrupted. This can be done by opening the dryer door (stopping the dryer) for 15 seconds. Closing the door and

pushing the "Start" button will repeat the ignition trial cycle.

DRYER SHUTDOWN

To render the dryer inoperati e, turn off the main gas shut off al e and disconnect the electrical supply to the

dryer.

NOTE: It is recommended that the installer test the dryer for operation and instruct the

user before lea ing the installation.

Andere Handbücher für T-30

Inhaltsverzeichnis

Andere Dexter Laundry Trockner Handbücher

Dexter Laundry

Dexter Laundry V Series Handbuch

Dexter Laundry

Dexter Laundry T-30 Bedienungsanleitung

Dexter Laundry

Dexter Laundry DC50X2 Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-20SWD Montageanleitung

Dexter Laundry

Dexter Laundry DN0170 XL Bedienungsanleitung

Dexter Laundry

Dexter Laundry O Series Kurzanleitung

Dexter Laundry

Dexter Laundry T-20 SWD Bedienungsanleitung

Dexter Laundry

Dexter Laundry DDAD30HC-59 Series Dryers Bedienungsanleitung

Dexter Laundry

Dexter Laundry C Series Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-30SWD Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-30X2 Bedienungsanleitung

Dexter Laundry

Dexter Laundry C Series Kurzanleitung

Dexter Laundry

Dexter Laundry T-30 Administratorhandbuch

Dexter Laundry

Dexter Laundry DDAD T-30 2 Series Administratorhandbuch

Dexter Laundry

Dexter Laundry DRC55 Series Bedienungsanleitung

Dexter Laundry

Dexter Laundry COIN COMPACT DRYER Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-20 SWD Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-30X2 Montageanleitung

Dexter Laundry

Dexter Laundry T-30 Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-50X2 Bedienungsanleitung

Dexter Laundry

Dexter Laundry O Series Kurzanleitung

Dexter Laundry

Dexter Laundry T-30 Bedienungsanleitung

Dexter Laundry

Dexter Laundry B-Series Bedienungsanleitung

Dexter Laundry

Dexter Laundry T-50X2 Leitfaden

Beliebte Trockner Handbücher anderer Marken

Bosch

Bosch WTA79200GB Bedienungsanleitung

Amana

Amana W10233410A Bedienungsanleitung

Asko

Asko T760 Bedienungsanleitung

Bosch

Bosch Logixx 10 WTB76556GB Technisches Datenblatt

Electrolux

Electrolux EW2H328R2 Bedienungsanleitung

Beko

Beko DS8433RX1M Bedienungsanleitung

Dawlance

Dawlance Spinner DS 6000 C Bedienungsanleitung

Electrolux

Electrolux TP5080TW Bedienungsanleitung

AEG

AEG TR838P4OB Bedienungsanleitung

Indesit

Indesit IDV 75 Bedienungsanleitung

Infiniton

Infiniton SD-DG85C Bedienungsanleitung

BOMANN

BOMANN WT 5019 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Bedienungsanleitung

Asko

Asko T793C Bedienungsanleitung

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Bedienungsanleitung

Frigidaire

Frigidaire CAQE7077KW0 Betriebsanleitung

Bosch

Bosch WTX8HKM9SN Bedienungsanleitung

Sharp

Sharp KD-NHH9S7GW2-PL Bedienungsanleitung