DFI EC800-AL Bedienungsanleitung
1
EC800-AL Installation Guide
Package Contents
www.dfi.com
•
1 EC800-AL system unit
•
Mounting screws for Mini PCIe modules
• Accessories for M.2 modules
•
1 Quick Installation Guide
•
1 CD disk includes:
-Drivers / Manual
Panel
Rear View
Front View
Note:
The system offers another SKU with a different combination of display outputs: VGA + 2 Micro HDMI. It also
supports dual-display and triple-display functions: VGA + 2 Micro HDMI or DVI + 2 Mini DP.
DFI reserves the right to change the specifications at any time prior to the product's release. For the latest revision and details of the
installation process, please refer to the user's manual.
HDD LED
(blue)
Reset Switch
Power Button
(green)
USB 3.0
Remote Power
Switch
Mic-in
USB 2.0
Status LED
(blue)
LAN 1
LAN 2
COM 1
DC-in
COM 2 Line-out
Mini DisplayPort
Antenna hole
DVI-I
(DVI-D signal)
Antenna hole
2
4. Lift the cover to open the system. The M.2 and Mini PCIe sockets are readily
accessible after removing the bottom cover.
Removing the Chassis Cover
Please observe the following guidelines and follow the procedure to open the
system.
1. Make sure the system and all other peripheral devices connected to it have
been powered off.
2. Disconnect all power cords and cables.
3. The 4 mounting screws on the bottom side of the system are used to secure
the cover to the chassis. Remove these screws and then put them in a safe
place for later use.
Chassis screw
Chassis screw
M.2 socekt
Mini PCIe socket
3
Installing an M.2 Card
To install a 42mm M.2 card:
1. Align the notch at the edge of the M.2 card with the key in the connector.
2. Insert the M.2 card into the connector.
3. Place the plastic spacer on top of the screw hole; push down on the other
end of the M.2 card and use the provided mounting screw (the longer one) to
secure the card on the system board.
The system is equipped with two M.2 sockets, supporting one M.2 22x42mm (B
key) and one M.2 22x30mm (AE key) form factor.
Mounting screw
4
To install a 30mm M.2 card:
1. Align the notch at the edge of the M.2 card with the key in the connector.
2. Insert the M.2 card into the connector.
3. Push down on the other end of the M.2 card and use the provided mounting
screw (the shorter one) to secure the card on the system board.
Mounting screw
5
Notes:
1. The 42mm M.2 slot provides PCIe, USB, and SATA signals (for common mobile
broadband and storage modules) whereas the 30mm M.2 slot provides only PCIe and
USB signals (for common Wi-Fi and Bluetooth modules).
2. To switch between PCIe and SATA signals for the 42mm M.2 slot, refer to Jumper
Settings below.
To install both 42mm and 30mm M.2 cards:
1. Align the notch at the edge of the 30mm M.2 card with the key in the
connector.
2. Insert the 30mm M.2 card into the connector.
3. Push down on the other end of the card and place the plastic spacer on top of
the card.
4. Insert the 42mm M.2 card into the connector.
5. Push down on the other end of the card and use the provided mounting screw
(the longer one) to secure both cards on the system board.
Mounting screw
Mounting screw
6
Installing a Mini PCIe or an mSATA Card
Notes:
1. This Mini PCIe slot can accommodate either a Mini PCIe or an mSATA card; refer to
Jumper Settings for signal selection for this slot.
2. If installing a wireless module, route the antenna cable(s) along the side of the chassis
and underneath the system board to reach the antenna holes.
The system board is equipped with 1 Mini PCIe slot.
1. Grasp the Mini PCIe card by its edges and align the notch of the PCIe card
with the key in the connector on the system board.
2. Push down on the other end of the Mini PCIe card and use the provided
mounting screw to secure the card on the system board.
Mounting screw
7
Board Layout and Jumper Settings
Note:
You cannot use COM 2 and DIO at the same time.
Please set JP8 and JP9 together.
1
1
Reset
Power
DDR4
LAN 1
COM 2
JP6 JP1
Battery
LINE-out
DP
Intel
WGI211AT
JP9
LAN 1
DP
USB 3.0
USB 2.0
LAN 2 LAN 1
COM 1
MIC-in
DVI-I
Buzzer
DDR4
DDR4
DDR4
E3900 Series
Intel Atom
®
Intel
WGI211AT
Realtek
ALC262
1
11
1
JP3
JP2
JP8
Mini-PCIe/mSATA
COM 2/DIO
JP2, JP3
JP8, JP9
PCIe/SATA
Clear CMOS
JP1
JP6
SMBus (J19)
USB 2.0 (J3)
1
5
6
13
Power on/off (J11)
Standby LED
111
2
3
3
10 12
12
10 10
9
Clear CMOS Data JP6
Normal 1-2 On (default)
Clear CMOS 2-3 On
COM2 / DIO Pin Select JP8, JP9
COM 1-2, 4-5, 7-8,
10-11 On (default)
DIO 2-3, 5-6, 8-9,
11-12 On
Mini PCIe (CN15)
PCIe/SATA Select
JP2, JP3
mSATA 1-2 On
(default)
Mini PCIe 2-3 On
22x42mm M.2 (CN12)
PCIe/SATA Select
JP1
SATA 1-2 On
(default)
PCIe 2-3 On
www.dfi.com
A46801731
Andere Handbücher für EC800-AL
1
Inhaltsverzeichnis
Andere DFI Desktop Handbücher
DFI
DFI ED700-EHL22I Bedienungsanleitung
DFI
DFI DT122-SB Bedienungsanleitung
DFI
DFI WM343-MB Bedienungsanleitung
DFI
DFI RM641-HD Bedienungsanleitung
DFI
DFI WM343-SD Series Bedienungsanleitung
DFI
DFI VC230-AL Bedienungsanleitung
DFI
DFI EC70A-SU Bedienungsanleitung
DFI
DFI WM343-KD330 Bedienungsanleitung
DFI
DFI EC700-AL Bedienungsanleitung
DFI
DFI EC70B-SU Bedienungsanleitung
DFI
DFI KS310-IMX6 Bedienungsanleitung
DFI
DFI OPS100-SH Bedienungsanleitung
DFI
DFI DT122-HR Bedienungsanleitung
DFI
DFI EC800 Series Bedienungsanleitung
DFI
DFI EB100-KU Bedienungsanleitung
DFI
DFI RM641 Bedienungsanleitung
DFI
DFI WM342-KD Series Bedienungsanleitung
DFI
DFI EC510-SD Bedienungsanleitung
DFI
DFI EC700-AL Bedienungsanleitung
DFI
DFI EC200 Series Bedienungsanleitung
