DFI OPS100-SH Bedienungsanleitung

OPS100-SH Installation Guide

Package Contents

• One

OPS100-SH System Unit

• One

OPS-DB Docking Board

•

One Quick Installation Guide

•

One DVD disk includes:

- Manual

DFI reserves the right to change the specications at any time prior to

the product's release. For the latest revision and more details of the

installation procedure, please refer to the user's manual on the website.

Notes:

1. Throughout this guide the OPS100-SH may be referred to as the

OPS+ Module

2. The OPS-DB (referred to as the Docking Board) is an expansion dock, which

provides additional I/O connectivity.

www.d.com

Panel: OPS100-SH

Mic-in

Line-outPower Button

HDD LED

HDMI-in

USB 3.0

COM LAN

Reset Button

microSD Card

Antenna Hole(1)

Front View

Notes:

1. The OPS+ Module is equipped with a Wi-Fi module to provide Wi-Fi connectivity.

Please install antennas to these SMA connectors.

2. There may not be indicator light depending on the installed Wi-Fi module; for

example, the LED will not be lit for Intel®Dual Band Wireless-AC 8260.

Panel: OPS-DB

Rear View

HRS FX18 JAE TX25A

DP(B)

Power Button

DP(A)

COM USB 3.0

HDMI-out

USB 2.0

DC-in

Wireless LED(2)

Removing the Chassis Cover

1. Make sure the system and all other peripheral devices connected to it

have been powered-off.

2. Disconnect all power cords and cables.

3. The 6 mounting screws on the sides and top cover of the system

chassis, and the 3 screws that afx the front panel to the chassis should

all be removed to open the system. Put these screws in a safe place for

later use.

4. Lift the cover up to open the system.

5. The SODIMM sockets are readily accessible after removing the chassis

cover.

Mounting screw

CPU fan SODIMM

The OPS+ Module consists of a computing board in a wrapper chassis.

Pease observe the following guidelines and follow the procedure to open the

system.

Installing the OPS100-SH into a Display

2. Secure the module by attaching two screws on the front panel.

Integrating a computing system into a digital signage display is made easy

by standardizing the connectors and signals between an OPS+ Module

and an OPS-compliant display. Note that the OPS+ Module does not

support hot swapping; do not power on the display before the installation

is complete. Please use the following steps to install the OPS+ Module

into the display panel:

1. Align the OPS+ Module with the slot of the display and slide the module

into the slot. Note that the venting holes should face outward to allow

ambient airow.

Venting holes

Venting area of the panel

Note:

The location of the OPS slot may be at the side or at the bottom of the display

panel depending on the design.

Mounting screw holes

3. Power on the display panel. The OPS+ Module should be automatically

powered on.

2. Secure the module by tightening the thumbscrews on the front panel.

Installing the OPS100-SH into the OPS-DB

The OPS+ Module has an accompanying Docking Board and allows it to

serve as a standalone computing system. The plug and unplug mechanism

between the OPS+ Module and the Docking Board utilizes the combo

connector at the back of the module. Please use the following steps to

install the OPS+ Module into the Docking Board:

1. Align the OPS+ Module with the slot of the Docking Board and slide the

module into the slot. Note that the venting holes should face upward to

allow ambient airow.

3. Connect the included AC power adapter. Turn on the system by

pressing the power switch.

Docking Board

Thumbscrew

Power switch

Board Layout and Jumper Settings: OPS100-SH

67 57

G2 G1

M2 M1

96 1

J22

M.2 Type 2280-S2-M

(PCIe/SATA)

M.2 Type 2230-D2-E

(PCIe/USB)

Clear CMOS J23

Normal (default) 1-2 On

Clear CMOS 2-3 On

Top View

I C

Mic-in

I C

Line-out

LAN 1

Buzzer

139

JAE TX25A-80P

111 140

HRS FX18-60S

LPC

SPI Flash BIOS

DC-in

Reset

COM 1

USB 3.0 USB 3.0

MicroSD

Power-on

Xeon E3-1515M v5

Core™ i5-6440EQ

Core™ i3-6100E

Intel

CM236/HM170

DDR4_1 SODIMM

DDR4_2 SODIMM

Battery (J3)

Clear

CMOS

(J23)

CPU Fan (J1)

110

Bottom View

Board Layout and Jumper Settings: OPS-DB

140

B31

B32

A31

A32

110

111

Power-on

Line_out

(J5)

I2C (J6) GPIO (J4)

USB PWR

(J15)

PCIE1(PCIe 3.0 x4)

JAE TX24A-80R

HRS FX18-60P

DPB

DPA

HDMI 1

USB 2.0

USB 3.0

DC-in

+12V Slide Switch

USB PWR

(J16)

AT/ATX mode

(J17)

SYS Fan (J3)

COM 1

USB Power Select J15 (for the USB 3.0 port)

J16 (for the USB 2.0 ports)

5V 1-2 On

5V Standby (default) 2-3 On

AT/ATX Mode Select J17

ATX mode (default) 1-2 On

AT mode 2-3 On

Connector Pin Assignment

Pins Pin Assignment Description I/O(1) Pins Pin Assignment Description I/O

40 +12V~+19V Power - 80 GND Ground -

39 +12V~+19V Power - 79 GND Ground -

38 +12V~+19V Power - 78 GND Ground -

37 +12V~+19V Power - 77 GND Ground -

36 +12V~+19V Power - 76 GND Ground -

35 +12V~+19V Power - 75 GND Ground -

34 +12V~+19V Power - 74 PWR_STATUS PowerGood OUT(OC)(2)

33 +12V~+19V/NC Power/NC - 73 PS_ON# Pluggable Signal ON IN

32 GND Ground - 72 PB_DET Pluggable Board Detect OUT

31 DVI0_HPD DVI-D IN 71 Not Available Not Available I/O

30 DVI0_DDC_CLK DVI-D I/O 70 AZ_LINEOUT_R Audio-R ch OUT

29 DVI0_DDC_DATA DVI-D I/O 69 AZ_LINEOUT_L Audio-L ch OUT

28 GND Ground - 68 GND Ground -

The OPS+ Module enables the integration of a pluggable module and a

display panel by employing the dened interconnect based on the JAE and

HRS combo plug and their receptacle connectors. The right angle blind

mate plug connector (p/n: JAE TX25A-80P-LT-H1E) should be mated with

the receptacle connector (p/n: JAE TX24A-80R-LT-H1E); together, they

provide interfacing for the following functions:

Power: DC-IN +12V~+19V@12A max

Display Interface: 2*HDMI 2.0 (or DVI or DP, 4K at 60Hz)

Audio: left and right Channel

USB: 1*USB 3.0 and 3*USB 2.0

Control and Sensors: 1*UART and Consumer Electronics Control (CEC, note

that the OPS100-SH does not support this function)

Control and Management Signals: the OPS+ Module power status, power-

on via display panel, OPS+ Module detect, Consumer Electronics Control

(CEC), system fan control, and device reset.

The following table lists the pin assignments of the 80-pin JAE connector:

27 TMDS0_2+ DVI-D OUT 67 USB_PP0 USB I/O

26 TMDS0_2- DVI-D OUT 66 USB_PN0 USB I/O

25 GND Ground - 65 GND Ground -

24 TMDS0_1+ DVI-D OUT 64 USB_PP1 USB I/O

23 TMDS0_1- DVI-D OUT 63 USB_PN1 USB I/O

22 GND Ground - 62 GND Ground -

21 TMDS0_0+ DVI-D OUT 61 USB_PP2 USB I/O

20 TMDS0_0- DVI-D OUT 60 USB_PN2 USB I/O

19 GND Ground - 59 GND Ground -

18 TMDS0_CLK+ DVI-D OUT 58 StdA_SSTX+ USB3.0 OUT

17 TMDS0_CLK- DVI-D OUT 57 StdA_SSTX- USB3.0 OUT

16 GND Ground - 56 GND GND -

15 DDP_HPD DisplayPort IN 55 StdA_SSRX+ USB3.0 IN

14 DDP_AUXP DisplayPort I/O 54 StdA_SSRX- USB3.0 IN

13 DDP_AUXN DisplayPort I/O 53 GND Ground -

12 GND Ground - 52 UART_TXD UART 3.3V OUT

11 DDP_0P DisplayPort OUT 51 UART_RXD UART 3.3V IN

10 DDP_0N DisplayPort OUT 50 SYS_FAN System Fan Control OUT

9GND Ground - 49 RSVD Reserved -

8DDP_1P DisplayPort OUT 48 RSVD Reserved -

7DDP_1N DisplayPort OUT 47 RSVD Reserved -

6GND Ground - 46 RSVD Reserved -

5DDP_2P DisplayPort OUT 45 RSVD Reserved -

4DDP_2N DisplayPort OUT 44 RSVD Reserved -

3GND Ground - 43 RSVD Reserved -

2DDP_3P DisplayPort OUT 42 RSVD Reserved -

1DDP_3N DisplayPort OUT 41 RSVD Reserved -

Notes:

(1) The I/O column denition is in reference to the OPS+ pluggable board.

(2) OC= Open Collector.

The right angle mate plug connector (p/n: FX18-60S-0.8SH) should be

mated with the receptacle connector (p/n: FX18-60P-0.8SH); together, they

provide interfacing for the following functions:

Power Contacts: 5V, [email protected] max

Display Interface: 1*DisplayPort 1.2 (4K at 60Hz)

PCI Express Expansion: 1*PCI-Express 3.0 x4

Control and Management Signals: 1*GPIO, 1*I2C, PHY device management

signals

The following table lists the pin assignments of the 60-pin HRS connector:

Pins Pin Assignment Description I/O(1) Pins Pin Assignment Description I/O

110 DDI1_TXP0 140 Hot Plug - Hot

Plug Detect

109 DDI1_TXN0 139 DDI1_TXP2

108 GND Ground 138 DDI1_TXN2

107 DDI1_TXP1 137 GND Ground

106 DDI1_TXN1 136 DDI1_TXP3

105 GND Ground 135 DDI1_TXN3

104 DDI_AUXP 134 GND Ground -

103 DDI_AUXN 133 GPIO GPIO

102 GND 132 PCIe_RST

101 I2C1_DATA1 I2C Data I/O 131 SLEEP_S3 PHY Status OUT

100 I2C1_CLK I2C Clock OUT 130 LAN_DISABLE PHY Status OUT

99 GND Ground 129 I2C_DATA_LAN I2C/SMBus Data I/O

98 PCIE_CLK_P PCIe CLK OUT 128 I2C_CLK_LAN I2C/SMBus CLK OUT

97 PCIE_CLK_N PCIe CLK OUT 127 GND Ground -

96 GND Ground 126 PCIE-TXP3 PCIe OUT

95 GND Ground -125 PCIE-TXN3 PCIe OUT

94 PCIE-RXP3 PCIe IN 124 GND Ground -

93 PCIE-RXN3 PCIe IN 123 GND Ground -

Andere Handbücher für OPS100-SH

Inhaltsverzeichnis

Andere DFI Desktop Handbücher

DFI

DFI EC510 Bedienungsanleitung

DFI

DFI EB100-KU Bedienungsanleitung

DFI

DFI ST101-CR Bedienungsanleitung

DFI

DFI RC300H-CS111 Bedienungsanleitung

DFI

DFI EC800 Series Bedienungsanleitung

DFI

DFI DT122-SD Bedienungsanleitung

DFI

DFI ES520-CD Bedienungsanleitung

DFI

DFI ES220-CS1S Bedienungsanleitung

DFI

DFI WM342-KD Series Bedienungsanleitung

DFI

DFI ED700-EHL22I Bedienungsanleitung

DFI

DFI EC800 Series Bedienungsanleitung

DFI

DFI DT122-SD Bedienungsanleitung

DFI

DFI ST102-SD Bedienungsanleitung

DFI

DFI DT122-GH Bedienungsanleitung

DFI

DFI RM641-HD Bedienungsanleitung

DFI

DFI DT122-SB Bedienungsanleitung

DFI

DFI EC800-AL Bedienungsanleitung

DFI

DFI EC700-AL Bedienungsanleitung

DFI

DFI U340 Series Bedienungsanleitung

DFI

DFI DT122-CR Bedienungsanleitung

DFI

DFI DT122-HR Bedienungsanleitung

DFI

DFI WM343-MB Bedienungsanleitung

DFI

DFI DT122-CR Bedienungsanleitung

DFI

DFI RM641 Bedienungsanleitung

Beliebte Desktop Handbücher anderer Marken

HP m9060n - Pavilion - Elite Technisches Datenblatt

Asus

Asus E210 Series Bedienungsanleitung

Dell

Dell Inspiron 600m Bedienungsanleitung

Dell

Dell Inspiron 3662 Bedienungsanleitung

TotalFlow

TotalFlow uFLO Bedienungsanleitung

HP Presario SV7000 - Desktop PC Bedienungsanleitung

HP ProDesk 400 G5 Handbuch

Logitech

Logitech MK320 Bedienungsanleitung

Dell

Dell XPS 730 H2C Bedienungsanleitung

Sony

Sony Vaio Series Bedienungsanleitung

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Bedienungsanleitung

Alto

Alto MD 250 Bedienungsanleitung

Lenovo

Lenovo ThinkCentre Edge 72 Handbuch

Lenovo

Lenovo ThinkStation D20 Handbuch

Arbor Technology

Arbor Technology FPC-7800 Series Bedienungsanleitung

Sony

Sony VAIO VGX-TP1 Series Bedienungsanleitung

Asus

Asus Eee Box B204 Bedienungsanleitung

Dell

Dell Optiplex 9010 All In One Bedienungsanleitung