DFI CM64-AL Bedienungsanleitung
90200547
CM64-AL
System Board
User’s Manual
Copyright
This publication contains information that is protected by copyright.
No part of it may be reproduced in any form or by any means or
used to make any transformation/adaptation without the prior
written permission from the copyright holders.
This publication is provided for informational purposes only. The
manufacturer makes no representations or warranties with respect to
the contents or use of this manual and specifically disclaims any
express or implied warranties of merchantability or fitness for any
particular purpose.The user will assume the entire risk of the use or
the results of the use of this document. Further, the manufacturer
reserves the right to revise this publication and make changes to its
contents at any time, without obligation to notify any person or
entity of such revisions or changes.
© 2005. All Rights Reserved.
Trademarks
Windows®98, Windows®98 SE, Windows®ME, Windows®2000,
Windows NT®4.0 and Windows®XP are registered trademarks of
Microsoft Corporation. VIA is a registered trademark of VIA
Technologies, Inc. Award is a registered trademark of Award Soft-
ware, Inc. Other trademarks and registered trademarks of products
appearing in this manual are the properties of their respective
holders.
FCC and DOC Statement on Class B
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio TV technician for
help.
Notice:
1. The changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority
to operate the equipment.
2. Shielded interface cables must be used in order to comply with
the emission limits.
Table of Contents
About this Manual................................................................................
Warranty.....................................................................................................
Static Electricity Precaution................................................................
Safety Measures.....................................................................................
About the Package...............................................................................
Before Using the System Board.........................................................
Chapter 1 - Introduction....................................................................
Specifications...................................................................................................................................
Features..............................................................................................................................................
Chapter 2 - Hardware Installation....................................................
System Board Layout ..........................................................................................................
System Memory..........................................................................................................................
CPU.......................................................................................................................................................
Jumper Settings............................................................................................................................
Rear Panel I/O Ports.............................................................................................................
Internal I/O Connectors.....................................................................................................
Chapter 3 - BIOS Setup......................................................................
Award BIOS Setup Utility.................................................................................................
Updating the BIOS..................................................................................................................
Chapter 4 - Supported Softwares.....................................................
Drivers, Utilities and Software Applications......................................................
Installation Notes.......................................................................................................................
Appendix A - System Error Messages...............................................
POST Beep.................................................................................................................................
Error Messages.........................................................................................................................
Appendix B - Troubleshooting..........................................................
Troubleshooting Checklist...............................................................................................
5
5
6
6
7
7
8
8
10
13
13
14
16
17
23
34
47
47
79
81
81
84
85
85
85
87
87
About this Manual
An electronic file of this manual is included in the CD. To view the
user’s manual in the CD, insert the CD into a CD-ROM drive. The
autorun screen (Main Board Utility CD) will appear. Click “User’s
Manual” on the main menu.
Warranty
1. Warranty does not cover damages or failures that arised from
misuse of the product, inability to use the product, unauthorized
replacement or alteration of components and product
specifications.
2. The warranty is void if the product has been subjected to
physical abuse, improper installation, modification, accidents or
unauthorized repair of the product.
3. Unless otherwise instructed in this user’s manual, the user may
not, under any circumstances, attempt to perform service,
adjustments or repairs on the product, whether in or out of
warranty. It must be returned to the purchase point, factory or
authorized service agency for all such work.
4. We will not be liable for any indirect, special, incidental or
consequencial damages to the product that has been modified
or altered.
Introduction
1
6
Static Electricity Precautions
It is quite easy to inadvertently damage your PC, system board,
components or devices even before installing them in your system
unit. Static electrical discharge can damage computer components
without causing any signs of physical damage. You must take extra
care in handling them to ensure against electrostatic build-up.
1. To prevent electrostatic build-up, leave the system board in its
anti-static bag until you are ready to install it.
2. Wear an antistatic wrist strap.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of
the components, contacts or connections.
5. Avoid touching the pins or contacts on all modules and
connectors. Hold modules or connectors by their ends.
Important:
Electrostatic discharge (ESD) can damage your processor, disk
drive and other components. Perform the upgrade instruction
procedures described at an ESD workstation only. If such a
station is not available, you can provide some ESD protection
by wearing an antistatic wrist strap and attaching it to a metal
part of the system chassis. If a wrist strap is unavailable,
establish and maintain contact with the system chassis
throughout any procedures requiring ESD protection.
Safety Measures
To avoid damage to the system:
• Use the correct AC input voltage range.....
To reduce the risk of electric shock:
• Unplug the power cord before removing the system chassis
cover for installation or servicing. After installation or servicing,
cover the system chassis before plugging the power cord.
Battery:
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend
by
the manufacturer.
• Dispose of used batteries according to the battery
manufacturer’s
instructions.
1
Introduction
7
About the Package
The system board package contains the following items. If any of
these items are missing or damaged, please contact your dealer or
sales representative for assistance.
;The system board
;A user’s manual
;One IDE cable
;One floppy cable
;One “Mainboard Utility” CD
The system board and accessories in the package may not come
similar to the information listed above. This may differ in accordance
to the sales region or models in which it was sold. For more
information about the standard package in your region, please
contact your dealer or sales representative.
Before Using the System Board
Before using the system board, prepare basic system components.
If you are installing the system board in a new system, you will need
at least the following internal components.
•A CPU
•Memory module
•Storage devices such as hard disk drive, CD-ROM, etc.
You will also need external system peripherals you intend to use
which will normally include at least a keyboard, a mouse and a video
display monitor.
Introduction
1
8
Chapter 1 - Introduction
Specifications
Processor
Chipset
System Memory
Expansion Slots
BIOS
Power Management
Hardware Monitor
Graphics
Audio
Pentium®III
- FCPGA2 133MHz FSB (1.13GHz-1.26GHz on 0.13µ)
- FCPGA 133MHz FSB (533EB-1GHz)
- FCPGA 100MHz FSB (500E-1.1GHz)
CeleronTM
- FCPGA2 100MHz FSB (≥1.2GHz on 0.13µ)
- FCPGA 100MHz FSB (800MHz-1.1GHz)
VIA®chipset
- North bridge: VIA®Apollo PLE133T 8601T
- South bridge: VIA®82C686B
Supports up to 1GB using VCM (Virtual Channel Memory) or
PC SDRAM DIMM (unbuffered or registered)
Two 168-pin DIMM sockets
Uses x64 PC SDRAM, 3.3V
- PC-100 SDRAM DIMM for 100MHz FSB processors
- PC-133 SDRAM DIMM for 133MHz FSB processors
4 PCI slots
3 ISA slots
Award BIOS
2Mbit flash memory
ACPI and OS Directed Power Management
ACPI STR (Suspend to RAM) function
Wake-On-PS/2 Keyboard/Mouse
Wake-On-USB Keyboard/Mouse
Wake-On-LAN
Wake-On-Ring
RTC timer to power-on the system
AC power failure recovery
Monitors CPU/system temperature and overheat alarm
Monitors VCORE/3.3V/5V/12V voltages and failure alarm
Monitors CPU/chassis fan speed and failure alarm
CPU Overheat Protection function monitors CPU temperature
during system boot-up
Integrated Trident 2D/3D video accelerator
Realtek ALC202A AC’97 audio CODEC
2-channel audio output
1
Introduction
9
LAN
IDE
Rear Panel I/O
Internal I/O
PCB
Realtek RTL8100C PCI LAN
Fully compliant to IEEE 802.3 (10BASE-T) and 802.3u
(100BASE-TX) standards
Supports two IDE connectors that allows connecting up to four
UltraDMA 100Mbps hard drives
1 mini-DIN-6 PS/2 mouse port
1 mini-DIN-6 PS/2 keyboard port
1 RJ45 LAN port
2 USB 1.1 ports
1 parallel port
1 COM port
1 VGA port
1 game port
Line-out, line-in and mic-in jacks
1 connector for 2 additional external USB 1.1 ports
1 connector for 1 external COM port
1 front audio connector for external line-out and mic-in jacks
1 CD-in internal audio connector
1 AUX-in internal audio connector
1 IrDA connector
2 IDE connectors
1 floppy connector
1 Wake-On-LAN connector
1 Wake-On-Ring connector
1 20-pin ATX main power connector
1 front panel connector
2 fan connectors
ATX form factor
20.1cm (7.92") x 30.5cm (12")
Introduction
1
10
Features
The integrated Trident video accelerator supports
optimized Shared Memory Architecture (SMA) and
shares 8MB of the system memory. 3D rendering
features 32-bit true color rendering and MPEG-2 video
textures. It also supports 2D hardware acceleration features.
CPU Overheat Protection has the capability of
monitoring the CPU’s temperature during system boot
up. Once the CPU’s temperature exceeded the
temperature limit pre-defined by the CPU, the system will automatically
shutdown. This preventive measure has been added to protect the
CPU from damage and insure a safe computing environment.
The two DIMM sockets support PC SDRAM
DIMMs. PC SDRAM (Synchronous Dynamic
Random Access Memory) uses a fast memory interface technology
that includes using the clock on the chip to synchronize with the
CPU clock so that the timing of the memory chips and the timing of
the CPU are synchronized. This saves time during transmission of
data, subsequently increasing system performance.
The onboard Realtek ALC202A which is an AC’97
compatible audio codec supports 2-channel audio
output.
The Realtek RTL8100C PCI LAN supports up to
100Mbps.
CPU
Overheat
Protection
PC SDRAM
AUDIO
Andere Handbücher für CM64-AL
1
Inhaltsverzeichnis
Andere DFI Hauptplatine Handbücher
DFI
DFI PT332-DRM Bedienungsanleitung
DFI
DFI KM266Pro-MLV Bedienungsanleitung
DFI
DFI P4M266A-MLV Bedienungsanleitung
DFI
DFI PIC-Q170/H110 Bedienungsanleitung
DFI
DFI G7S600-B Bedienungsanleitung
DFI
DFI AK34-SC Bedienungsanleitung
DFI
DFI SD630-H110 Bedienungsanleitung
DFI
DFI PB50-ZX Bedienungsanleitung
DFI
DFI SR100-L20C Bedienungsanleitung
DFI
DFI KD331-C236/Q170 Bedienungsanleitung
DFI
DFI ADS630 Bedienungsanleitung
DFI
DFI CS100 Series Bedienungsanleitung
DFI
DFI ak75-ec A+ Bedienungsanleitung
DFI
DFI AD75 Bedienungsanleitung
DFI
DFI NB71-SC Bedienungsanleitung
DFI
DFI G586VPS Pro Bedienungsanleitung
DFI
DFI 748-AL Bedienungsanleitung
DFI
DFI AM75-EC Bedienungsanleitung
DFI
DFI Infinity NF series Bedienungsanleitung
DFI
DFI 586ITB Bedienungsanleitung
Beliebte Hauptplatine Handbücher anderer Marken
Gigabyte
Gigabyte GA-9IVDT Bedienungsanleitung
Texas Instruments
Texas Instruments ADS8372EVM Bedienungsanleitung
Commell
Commell MS-C73 Bedienungsanleitung
IBT Technologies
IBT Technologies MB860 Bedienungsanleitung
Nvidia
Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung
Biostar
Biostar M7VIT Bravo Bedienungs- und Montageanleitung
