DFI COM630-B Bedienungsanleitung

Introduction

COM630-B

Carrier Board

User’s Manual

935-COM631-050G

I01400909

Introduction

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior writ-

ten permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any ex-

press or implied warranties of merchantability or fitness for any par-

ticular purpose.The user will assume the entire risk of the use or the

results of the use of this document. Further, the manufacturer re-

serves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or en-

tity of such revisions or changes.

Trademarks

Product names or trademarks appearing in this manual are for iden-

tification purpose only and are the properties of the respective own-

ers.

Introduction

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation.This equipment generates, uses and can radiate radio fre-

quency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communi-

cations. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following meas-

ures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

2. Shielded interface cables must be used in order to comply with

the emission limits.

Introduction

Table of Contents

Warranty.................................................................................................

Static Electricity Precaution................................................................

Safety Measures.....................................................................................

About the Package...............................................................................

Chapter 1 - Introduction....................................................................

Specifications...................................................................................................................................

Chapter 2 - Hardware Installation....................................................

System Board Layout ..........................................................................................................

Jumper Settings............................................................................................................................

Rear Panel I/O Ports.............................................................................................................

I/O Connectors..........................................................................................................................

Introduction

Warranty

1. Warranty does not cover damages or failures that arised from

misuse of the product, inability to use the product, unauthorized

replacement or alteration of components and product specifica-

tions.

2. The warranty is void if the product has been subjected to physi-

cal abuse, improper installation, modification, accidents or unau-

thorized repair of the product.

3. Unless otherwise instructed in this user’s manual, the user may

not, under any circumstances, attempt to perform service, adjust-

ments or repairs on the product, whether in or out of warranty.

It must be returned to the purchase point, factory or authorized

service agency for all such work.

4. We will not be liable for any indirect, special, incidental or

consequencial damages to the product that has been modified

or altered.

Introduction

Static Electricity Precautions

It is quite easy to inadvertently damage your PC, system board,

components or devices even before installing them in your system

unit. Static electrical discharge can damage computer components

without causing any signs of physical damage. You must take extra

care in handling them to ensure against electrostatic build-up.

1. To prevent electrostatic build-up, leave the board in its anti-static

bag until you are ready to install it.

2. Wear an antistatic wrist strap.

3. Do all preparation work on a static-free surface.

4. Hold the device only by its edges. Be careful not to touch any of

the components, contacts or connections.

5. Avoid touching the pins or contacts on all modules and connec-

tors. Hold modules or connectors by their ends.

Important:

Electrostatic discharge (ESD) can damage your processor,

disk drive and other components. Perform the upgrade in-

struction procedures described at an ESD workstation

only. If such a station is not available, you can provide

some ESD protection by wearing an antistatic wrist strap

and attaching it to a metal part of the system chassis. If a

wrist strap is unavailable, establish and maintain contact

with the system chassis throughout any procedures requir-

ing ESD protection.

Safety Measures

To avoid damage to the system:

• Use the correct AC input voltage range.....

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend

the manufacturer.

• Dispose of used batteries according to local ordinance.

Introduction

About the Package

The package contains the following items. If any of these items are

missing or damaged, please contact your dealer or sales representa-

tive for assistance.

;The system board

;One IDE cable

;One floppy cable

;One bracket mounted with 2 USB ports

;Two Serial ATA data cables

;Two Serial ATA power cables

;One bracket mounted with a COM port

;One I/O shield

;One QR (Quick Reference)

The board and accessories in the package may not come similar to

the information listed above. This may differ in accordance to the

sales region or models in which it was sold. For more information

about the standard package in your region, please contact your

dealer or sales representative.

Introduction

Audio

Serial ATA

IDE

I/O Chip 1

I/O Chip 2

Damage Free

Intelligence

Temperature

Humidity

Rear Panel I/O

Ports

• Realtek ALC655 AC97 audio codec

• 6-channel audio output

• SATA speed up to 3Gb/s

• 4 SATA ports

• Supports up to Ultra ATA 100

• One IDE channel supports up to 2 IDE devices

Note: We do not recommend using IDE devices and CF card at

the same time.

• Winbond 83627HG-AW controller

• LPC interface

• Watchdog timer function

• Default I/O port address "2eh"

• Fintek F81216D controller

•LPC interface

• Supports 4 COM ports

• Supports IrDA

• Default I/O port address "4eh"

• Monitors system temperature and overheat alarm

• Monitors system fan speed and failure alarm

• Operating: 0oC to 60oC

• Non-operating: -40oC to 85oC

• Operating: 10% to 90%

• 1 mini-DIN-6 PS/2 mouse port

• 1 mini-DIN-6 PS/2 keyboard port

• 3 DB-9 serial ports

• 1 DB-15 VGA port

• 1 RJ45 LAN port

• 4 USB 2.0/1.1 ports

• Mic-in, line-in and line-out

Chapter 1 - Introduction

Specifications

Introduction

I/O Connectors

Expansion Slots

COM Express

Connectors

PCB

• 2 connectors for 4 additional external USB 2.0/1.1 ports

• 1 connector for an external serial port

• 1 LVDS LCD panel connector

• 1 LCD/inverter power connector

• 1 Digital I/O connector

• 1 Digital I/O power connector

• 1 GPIO connector

• 1 front audio connector for line-out and mic-in jacks

• 1 CD-in internal audio connector

• 1 S/PDIF-in/out connector

• 1 connector for IrDA interface

• 4 Serial ATA connectors

• 1 40-pin IDE connector

• 1 FDD connector

• 1 parallel connector (optional)

• 1 24-pin ATX power connector

• 1 4-pin 12V power connector

• 1 Wake-On-Ring connector

• 1 chassis open connector

• 1 front panel connector

• 3 fan connectors

• 1 diagnostic LED (optional)

• 1 CompactFlash socket

• 1 PCI Express x16 (Graphics or Dual SDVO)

• 2 PCI Express x1

• 4 PCI slots (PCI 2.3, 32-bit, 33MHz)

• Two 220-pin COM Express standard connectors

• 4 layers, ATX form factor

• 30.5cm (12") x 24.4cm (9.6")

Hardware Installation

Chapter 2 - Hardware Installation

System Board Layout

VGA

COM 4

COM 1

COM 2

LAN

USB 0

USB 1

USB 2

USB 3

Mic-in

Line-out

Line-in

IrDA

WOR

COM 3

PS/2 power

select ( )JP13

COM Express connector

D1 D110

C1 C110

B1 B110

A1 A110

USB 0-3 power

select ( )JP5

+12V power

Standby

Power LED

CD-in

S/PDIF

Audio

codec

PCI Express x16

PCI Express x1

PCI 4

PCI 3

PCI 2

PCI 1

Front audio

Power-on

select (JP14)

Chassis

open

Winbond

W83627

DIO Parallel

USB 4-5

USB 4-7 power

select ( )JP6

USB 6-7

Fan 1

Front

panel

Fan 2

CF socket

setting (JP15)

CompactFlash socket

LCD/Inverter

power

Panel power

select (J 3)P

LVDS LCD Panel

SATA 2

SATA 3

SATA 0

SATA 1

Battery

GPIO

IDE FDD

113

2412

ATX

power

Fan 3

power

DIO

Mouse

Andere Handbücher für COM630-B

Inhaltsverzeichnis

Andere DFI Hauptplatine Handbücher

DFI

DFI CS331-C246 Bedienungsanleitung

DFI

DFI CMS631-Q470E Bedienungsanleitung

DFI

DFI AD72-SC Bedienungsanleitung

DFI

DFI NB72-SC Bedienungsanleitung

DFI

DFI LANPARTY UT 915P-T12 Bedienungsanleitung

DFI

DFI G586OP Bedienungsanleitung

DFI

DFI PB50-V3 Bedienungsanleitung

DFI

DFI CM100-C Bedienungsanleitung

DFI

DFI CS101-H310 Bedienungsanleitung

DFI

DFI KU553 Bedienungsanleitung

DFI

DFI LanParty 925X-T2 Bedienungsanleitung

DFI

DFI AK70 Bedienungsanleitung

DFI

DFI SD100-H110/Q170 Bedienungsanleitung

DFI

DFI G586IPV Bedienungsanleitung

DFI

DFI Infinity NF650I Ultra Bedienungsanleitung

DFI

DFI P2BLX Bedienungsanleitung

DFI

DFI CS101-C246 Bedienungsanleitung

DFI

DFI HD636-H81CS Bedienungsanleitung

DFI

DFI SU171 Bedienungsanleitung

DFI

DFI AD75 Bedienungsanleitung

DFI

DFI KM400A-MLV Bedienungsanleitung

DFI

DFI PB64-BX Bedienungsanleitung

DFI

DFI G586OPC/E Bedienungsanleitung

DFI

DFI CS620 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung