DFI CT930-B Bedienungsanleitung

CT930-B

ECX Board

User’s Manual

935-CT9303-050G

I01910743

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior writ-

ten permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any ex-

press or implied warranties of merchantability or fitness for any par-

ticular purpose.The user will assume the entire risk of the use or the

results of the use of this document. Further, the manufacturer re-

serves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or en-

tity of such revisions or changes.

Trademarks

Product names or trademarks appearing in this manual are for iden-

tification purpose only and are the properties of the respective own-

ers.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation.This equipment generates, uses and can radiate radio fre-

quency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communi-

cations. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following meas-

ures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

2. Shielded interface cables must be used in order to comply with

the emission limits.

Table of Contents

About this Manual................................................................................

Warranty.................................................................................................

Static Electricity Precaution................................................................

Safety Measures.....................................................................................

About the Package...............................................................................

Before Using the System Board.........................................................

Chapter 1 - Introduction....................................................................

Specifications...................................................................................................................................

Features..............................................................................................................................................

Chapter 2 - Hardware Installation....................................................

System Board Layout ..........................................................................................................

Mechanical Diagram................................................................................................................

System Memory..........................................................................................................................

CPU.......................................................................................................................................................

Jumper Settings............................................................................................................................

Rear Panel I/O Ports.............................................................................................................

I/O Connectors..........................................................................................................................

Chapter 3 - BIOS Setup......................................................................

Award BIOS Setup Utility.................................................................................................

Updating the BIOS..................................................................................................................

Chapter 4 - Supported Softwares.....................................................

Drivers for Windows Vista System..........................................................................

Drivers for Windows XP System..............................................................................

Installation Notes.......................................................................................................................

Appendix A - System Error Messages...............................................

Appendix B - Troubleshooting..........................................................

Appendix C - Watchdog Timer........................................................

100

114

115

117

121

About this Manual

An electronic file of this manual is included in the CD. To view the

user’s manual in the CD, insert the CD into a CD-ROM drive. The

autorun screen (Main Board Utility CD) will appear. Click “User’s

Manual” on the main menu.

Warranty

1. Warranty does not cover damages or failures that arised from

misuse of the product, inability to use the product, unauthorized

replacement or alteration of components and product specifica-

tions.

2. The warranty is void if the product has been subjected to physi-

cal abuse, improper installation, modification, accidents or unau-

thorized repair of the product.

3. Unless otherwise instructed in this user’s manual, the user may

not, under any circumstances, attempt to perform service, adjust-

ments or repairs on the product, whether in or out of warranty.

It must be returned to the purchase point, factory or authorized

service agency for all such work.

4. We will not be liable for any indirect, special, incidental or

consequencial damages to the product that has been modified

or altered.

Introduction

Static Electricity Precautions

It is quite easy to inadvertently damage your PC, system board,

components or devices even before installing them in your system

unit. Static electrical discharge can damage computer components

without causing any signs of physical damage. You must take extra

care in handling them to ensure against electrostatic build-up.

1. To prevent electrostatic build-up, leave the system board in its

anti-static bag until you are ready to install it.

2. Wear an antistatic wrist strap.

3. Do all preparation work on a static-free surface.

4. Hold the device only by its edges. Be careful not to touch any of

the components, contacts or connections.

5. Avoid touching the pins or contacts on all modules and connec-

tors. Hold modules or connectors by their ends.

Important:

Electrostatic discharge (ESD) can damage your processor,

disk drive and other components. Perform the upgrade in-

struction procedures described at an ESD workstation

only. If such a station is not available, you can provide

some ESD protection by wearing an antistatic wrist strap

and attaching it to a metal part of the system chassis. If a

wrist strap is unavailable, establish and maintain contact

with the system chassis throughout any procedures requir-

ing ESD protection.

Safety Measures

To avoid damage to the system:

• Use the correct AC input voltage range.....

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis

cover for installation or servicing. After installation or servicing,

cover the system chassis before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend

the manufacturer.

• Dispose of used batteries according to local ordinance.

Introduction

About the Package

The system board package contains the following items. If any of

these items are missing or damaged, please contact your dealer or

sales representative for assistance.

;The system board

;One IDE cable (44-pin to 44-pin)

;One audio cable - Speaker-out, mic-in and line-in (optional)

;One serial cable

;One Serial ATA data cable

;One Serial ATA power cable

;One PS/2 keyboard/mouse cable

;One power cable

;One CPU cooler

;One “Main Board Utility” CD

;One QR (Quick Reference)

The system board and accessories in the package may not come

similar to the information listed above.This may differ in accordance

to the sales region or models in which it was sold. For more infor-

mation about the standard package in your region, please contact

your dealer or sales representative.

Before Using the System Board

Before using the system board, prepare basic system components.

If you are installing the system board in a new system, you will need

at least the following internal components.

•A CPU

•Memory module

•Storage devices such as hard disk drive, CD-ROM, etc.

You will also need external system peripherals you intend to use

which will normally include at least a keyboard, a mouse and a video

display monitor.

Important:

Use the power cable included in the package. This cable is

exclusively for CT930-B. Refer to the I/O Connectors section in

chapter 2 for the pin functions of the power connector.

Introduction

Processor

Chipset

System Memory

BIOS

Energy Efficient

Design

Damage Free

Intelligence

• Intel®CoreTM Duo/Solo processor

- 667MHz/533MHz system data bus

• Intel®Celeron®M processor

- 533MHz system data bus

• Processor socket: mPGA478M

Note: Ultra Low Voltage (ULV) and Low Voltage (LV) processor

is available on special order.

• Intel®chipset

- Intel®945GME Express chipset

- Intel®82801GBM I/O Controller Hub (ICH7M)

• One 200-pin SODIMM socket

• Supports 400MHz, 533MHz and 667MHz DDR2 SDRAM

• Supports maximum of 2GB system memory using 256Mbit,

512Mbit or 1Gbit technology for x8 and x16 devices

• Award BIOS

• 4Mbit flash memory

• Supports ACPI specification and OS Directed Power Manage-

ment

• Wake-On-Events include:

- Wake-On-PS/2 Keyboard/Mouse

- Wake-On-USB Keyboard/Mouse

- Wake-On-LAN

- Wake-On-Ring

- RTC timer to power-on the system

• System power management supported

• CPU stopped clock control

• Microsoft®/Intel®APM 1.2 compliant

• Soft Power supported - ACPI v1.0a specification

• AC power failure recovery

• Monitors CPU/system temperature and overheat alarm

• Monitors CPU/system fan speed and failure alarm

• Read back capability that displays temperature, voltage and fan

speed

Chapter 1 - Introduction

Specifications

Introduction

Graphics

Audio

LAN

Serial ATA

IDE Interface

I/O Ports

I/O Connectors

• Integrated graphics interface

- Analog CRT

- Integrated 400MHz RAMDAC

- Analog monitor supports up to UXGA

- LVDS interface

- Panel support up to UXGA (1600x1200)

- 25MHz-112MHz single/dual channel @ 18bpp, TFT panel

type support

• Internal graphics features

- DVMT 3.0 support

- Intel®Dual-Frequency Graphics Technology

- Intel®Smart 2D Display Technology

- Dual Independent display pipes

- Intel Gen 3.5 Integrated Graphics Engine

• Realtek ALC655

• 16-bit stereo full-duplex codec with independent variable sam-

pling rate

• 5.1-channel audio output

• One Marvell 88E8053 PCI Express Gigabit controller

• Supports 10Mbps, 100Mbps and 1Gbps data transmission

• IEEE 802.3 (10/100Mbps) and IEEE 802.3ab (1Gbps) compliant

• Supports 2 SATA (Serial ATA) interfaces which are compliant

with SATA 1.0 specification

• SATA speed up to 1.5Gb/s

• One 44-pin IDE connector supports up to two IDE devices

• Supports Ultra ATA 100/66/33 (this will depend on the IDE cable

used)

Note: We do not recommend using IDE devices and CF card at

the same time.

• 1 DB-15 VGA port

• 1 TV-Out (S-Video I/F) - Does not support Macrovision

• 1 RJ45 LAN port

• 2 USB 2.0/1.1 ports

• 1 port for PS/2 Keyboard and PS/2 Mouse ports

• 1 DB-9 serial port

• 2 Serial ATA ports

• 1 CompactFlash socket

Note: By default, CompactFlash is fixed in Slave mode.

• 1 connector for 1 external serial port

• 1 LVDS LCD panel connector

• 1 LCD/inverter power connector

• 1 audio connector for mic-in, line-in and line-out jacks

• 1 44-pin IDE connector

• 1 10-pin ATX power connector

• 1 front panel connector

• 2 fan connectors

Introduction

Temperature

Humidity

PCB

Daughterboard

Connector

EXT-ECX1

Daughterboard

(optional)

•0

oC to 60oC

• 10% to 90%

• 10 layers, ECX form factor

• 10.5cm (4.14") x 14.6cm (5.75")

• 1 daughterboard connector for EXT-ECX1daughterboard

• Chrontel CH7307C DVI transmitter chip

• 2 USB ports

• 1 DVI port

• 1 mini PCI slot

• 4 layers

• 9.35cm (3.68") x 9.55cm (3.76")

Inhaltsverzeichnis

Andere DFI Hauptplatine Handbücher

DFI

DFI ADS310-R680E/Q670E Bedienungsanleitung

DFI

DFI LanParty nF4 Bedienungsanleitung

DFI

DFI NS80-EA Bedienungsanleitung

DFI

DFI G7B630-N Bedienungsanleitung

DFI

DFI P5BV3+/e Bedienungsanleitung

DFI

DFI CS631-C246 Bedienungsanleitung

DFI

DFI AL102 Bedienungsanleitung

DFI

DFI 586ITX Bedienungsanleitung

DFI

DFI AD73 Pro Bedienungsanleitung

DFI

DFI CA64-TC Bedienungsanleitung

DFI

DFI BT253 Bedienungsanleitung

DFI

DFI SD330 Bedienungsanleitung

DFI

DFI G586IPC Bedienungsanleitung

DFI

DFI PW65 Series Bedienungsanleitung

DFI

DFI AR100-DR Bedienungsanleitung

DFI

DFI WL051 Bedienungsanleitung

DFI

DFI NB32-SL Bedienungsanleitung

DFI

DFI BT160 Bedienungsanleitung

DFI

DFI Blood-Iron LanParty Bi 785G-M35 Bedienungsanleitung

DFI

DFI 845GV-MLV Bedienungsanleitung

DFI

DFI LT600-DR/D/L Bedienungsanleitung

DFI

DFI AK74-SC Bedienungsanleitung

DFI

DFI SB331-D Bedienungsanleitung

DFI

DFI 845GV-MLV Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung