Digi TA2020B Bedienungsanleitung

2000 Series Routers

ISDN Terminal Adapter

ISDN Router

Installation Guide

TA2020B & IR2110B Installation Guide

Disclaimer

Digi International makes no representations or warranties with respect to the contents or

use of this manual, any software drivers or associated application software provided with

this product and specifically disclaims any expressed or implied warranties of

merchantability or fitness for any particular purpose.

Digi International reserve the right to modify or revise all or part of this document, its

contents, and any products described herein at any time without prior notification and

shall not be responsible for any loss, cost, or damage, including consequential damage,

caused by reliance on these materials.

Product disposal instructions

The WEEE (Waste Electrical and Electronic Equipment: 2002/96/EC) directive has been

introduced to ensure that electrical/electronic products are recycled using the best

available recovery techniques to minimise the impact on the environment.

This product contains high quality materials and components which can be recycled. At

the end of its life this product MUST NOT be mixed with other commercial waste for

disposal. Check with the terms and conditions of your supplier for disposal information.

Digi International Ltd WEEE Registration number: WEE/HF1515VU

or mechanical, including photocopying, recording, taping, or information and retrieval

systems without written permission of Digi International.

May 2009. Part # 6211-0021 REV B

TA2020B & IR2110B Installation Guide

Safety Notices

1) Please read all instructions before installing and powering the unit. You should keep

these instructions in a safe place for future reference.

2) The TA2020B and IR2110B use a 12V DC/1.5A power supply (mains adapter). If the

mains adapter shows signs of damage or malfunction, you should stop using it

immediately - turn off the power at the mains and disconnect it from the mains supply

before contacting your supplier for a repair or replacement.

3) Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment. Use only the

accessories, attachments, and power supplies provided by the manufacturer –

connecting non-approved antennas or power supplies may damage the unit, cause

interference or create an electric shock hazard, and will void your warranty.

4) Do not attempt to repair the product. The unit contains no electronic components that

can be serviced or replaced by the user. Any attempt to service or repair the unit by

the user will void the product warranty.

5) The TA2020B and IR2110B are designed for indoor use only and should be used in

an environment that is suitable for computers and other electronic equipment.

6) Ports that are capable of connecting to other apparatus are defined as SELV ports.

To ensure conformity with EN60950 ensure that these ports are only connected to

ports of the same type on other apparatus.

TA2020B & IR2110B Installation Guide

Preface

This guide describes the installation procedure for the TA2020B and IR2110B. It is

intended to provide sufficient information for you to be able to connect the unit to your

terminal equipment and power supply. A complete reference guide to the software

features that are available on the product is available separately in PDF format that can

be downloaded from the Digi International website (www.digi.com).

Both models feature:

1 x RS232 sync/async serial ports (25-way D)

1 x RS232 async serial port (9-way D)

1 x ISDN BRI interface

In addition to the above, the IR2110B also incorporates a 10/100-BaseT Ethernet port.

Package Contents

When you receive the router carefully unpack it and check the contents. These should

include:

TA2020B or IR2110B system unit (one of the following models) :

81-TA2020B-SSEU-00

81-IR2110B-SSEU-00

100V-230VAC, 50 - 60/13A –12V DC mains adapter

this Installation Guide

2M CAT5 LAN cable (IR2110B only)

If any item is missing or damaged, please contact your supplier. You should also make a

record of any damage that may have occurred during shipping and report it to the carrier.

TA2020B & IR2110B Installation Guide

1 Introduction

The TA2020B and IR2110B facilitate the transmission of data over ISDN networks.

The units can be configured either by using commands entered at the serial port (much

like a modem), or via the built-in Web interface. We recommend that you use the Web

interface whenever possible.

1.1 Front Panel Features

The front panel of the unit incorporates number of LED indicators depending on the model

as shown in the following illustration (IR2110B):

Status Indicators

The status indicators operate as follows:

Illuminates steady red when power is applied.

LAN

On the IR2110B illuminates steady when there is a network

connection to the LAN port and flashes when data is transmitted

or received.

ISDN:

D, B1, B2

Flash when data is transmitted/received over the ISDN D, B1 or

B2 channels.

DTE 0, 1

Illuminate steady if a terminal is connected to the respective

serial port and the DTR signal is on. Flashes when data is

transmitted or received. DTE 1 is only present on the TA2020B.

TA2020B & IR2110B Installation Guide

Rear Panel Features

The functions of these connectors are described in the following table:

12V DC

This jack socket is used to connect the unit to the power supply

using 12V DC mains adapter.

SERIAL 0

This 25-way D socket provides a synchronous/asynchronous

RS2322 serial port which may be used to connect the unit to a

compatible serial device. The unit is supplied with a suitable 2

metre serial cable. To comply with EMC requirements it should

not be used with a longer cable.

SERIAL 1

On the TA2020B this 9-way D socket provides an asynchronous

RS2322 serial port which may be used to connect the unit to a

compatible serial device. The unit is supplied with a suitable 2

metre serial cable. To comply with EMC requirements it should

not be used with a longer cable.

On the IR2110B, this port is disabled.

LAN

On the IR2110B this socket is used to connect the unit to a

10/100-BaseT LAN using the 2-metre STP (Shielded Twisted

Pair) cable supplied or a suitable alternative. This port is auto-

sensing for speed and wiring (straight-through or cross-over). To

comply with EMC requirements it should not be used with non-

STP cable.

ISDN

This socket is used to connect the unit to an ISDN line.

Reset switch

This is located on the underside of the unit near the front. Pressing the switch gently with

the tip of a pen or other suitable implement will generate a hardware reset.

TA2020B & IR2110B Installation Guide

2 Installation

The TA2020B and IR2110B are designed for indoor use (office or home). The router

should be positioned on a smooth, level surface making sure that there is adequate

ventilation. Do not expose the router to extremes of heat or cold, strong magnetic fields or

liquids.

Step 1 –Connecting the serial cable

For connection to a serial terminal device, connect the 25-way D plug on the serial cable

provided to the SERIAL connector on the rear of the unit. Connect the other end of the

cable (9-way D socket) to the terminal. If the serial connector on the terminal is not a 9-

way D plug, you will need a suitable adapter.

Step 2 –Connecting the LAN cable (if applicable)

Plug one end of one of the supplied 2 metre CAT5 cable into the RJ45 socket labelled

LAN 0. Plug the other end into the LAN socket on your PC or notebook.

Step 3 –Connecting the power supply

Plug the jack plug on the mains adapter into the socket labelled 12V DC. When power is

first applied, the ON indicator will illuminate and the unit will initiate a series of diagnostic

self-tests. During this process one or more of the other indicators, will flash to show that

the unit is busy. When the flashing stops, the unit is ready to use.

TA2020B & IR2110B Installation Guide

3 Configuration

Once the TA2020B or IR2110B has be installed and powered up, you must now configure

the unit so that it can communicate with your network and the Internet.

3.1 Configuring the TA2020B

The TA2020B is configurable only through its serial port.

To access the web interface through the unit's serial port (using Windows dial-up

networking) follow the steps below.

Note: To use Dial-up Networking you must have the TCP/IP >Dial-up adapter installed in

the Network Configuration for Windows. Check this by selecting Settings >Control Panel

>Network >Configuration.

Step 1 –Installing the driver file

You will need to install the “DIGI_MULTI_PORT.INF” driver file and create a Windows

PPP Dial-up Networking connection (DUN) for the unit as described below. This driver is

available from the Digi International website (www.digi.com). It is assumed that you

already have a basic knowledge of Windows networking concepts and terminology.

The precise procedure for installing the .inf driver file for the unit will vary slightly between

different versions of Windows. The following description applies to Windows XP. Start by

selecting Start >Control Panel >Phone and Modem Options. You must be in Classic

View. Select the Modems tab and you will see a dialog similar to the following:

Click on Add… to install a new modem driver.

TA2020B & IR2110B Installation Guide

Check the Don't detect my modem, I will select it from a list option before clicking

Next > to display the following dialog screen:

This screen lists the manufacturers and models of modem currently available on your

system. Click on Have Disk….

Use the Browse button to locate the DIGI_MULTI_PORT.INF file that was downloaded

earlier. A list of routers will appear in the Models list.

Each entry in the list is the same driver, set up for a different COM port. Choose the entry

corresponding to the COM port your router is connected to, and click Next >. The wizard

will ask you which COM port you wish to install the modem on.

Select the appropriate port and click Next >, and Windows will install the driver. Once

installation is complete click Finish to return to the Phone and Modem Options dialog,

where your unit will be listed:

Click on the OK button if you are satisfied with the installation.

Note: During the installation you may receive a warning that the driver is not digitally

signed. Click on Continue Installation to install the driver.

TA2020B & IR2110B Installation Guide

Step 2 –Creating a new Dial-Up Network connection

You now need to create a new DUN connection through which you can access your unit.

If you are planning to connect the unit directly to your PC for configuration purposes,

connect it to the appropriate COM port now using a suitable serial cable.

If you wish to configure a remote unit, make sure it is connected to a suitable ISDN line

and make a note of the ISDN number.

From the Windows Start menu, select All Programs >Accessories >Communications >

New Connection Wizard. You will be presented with the New Connection Wizard

introduction screen. Click on Next > to proceed to the Network Connection Type dialog

box.

Select the Connect to the network at my workplace radio-button then click on Next >:

Select the Dial-up connection radio-button then click on Next >.

From the Select a Device dialog, select the unit you have just installed and make sure that

any other devices in the list are unchecked. Click Next >.

You must now enter a name for the connection. It is helpful to choose a name that you will

easily remember such as “My Local TA” or “TA2020B - Bristol Office”. Click Next >. The

next dialog allows you to fill in the phone number for the connection.

If the connection is being created for direct local access using a COM port, you should set

the phone number to 123. This number will be intercepted by the unit and recognised as

an attempt to connect locally.

If the connection is being created for remote access, enter the correct ISDN telephone

number (including the area code) for the remote unit.

When you have done this click Next >. The final dialog screen will confirm that the

connection has been created and includes a check box to allow you to create a shortcut

on your desktop if necessary. Click on Finish to complete the task.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Digi Netzwerk-Router Handbücher

Digi

Digi CR4110 Bedienungsanleitung

Digi

Digi Connect Series Benutzerhandbuch

Digi

Digi TransPort WR41 Bedienungsanleitung

Digi

Digi TX64 Bedienungsanleitung

Digi

Digi TransPort WR11 Bedienungsanleitung

Digi

Digi Transport DR64-H Bedienungsanleitung

Digi

Digi TransPort WR31 Montageanleitung

Digi

Digi XLR PRO Bedienungsanleitung

Digi

Digi TransPort WR64 Anwendungshandbuch

Digi

Digi XPress Bedienungsanleitung

Digi

Digi One TS W Bedienungsanleitung

Digi

Digi TransPort WR11 XT Bedienungsanleitung

Digi

Digi TransPort LR54 Bedienungsanleitung

Digi

Digi 6310-DX Bedienungsanleitung

Digi

Digi TransPort WR21 Bedienungsanleitung

Digi

Digi TransPort WR11 Bedienungsanleitung

Digi

Digi Connect EZ 4 Bedienungsanleitung

Digi

Digi ConnectPort WAN GPS Bedienungsanleitung

Digi

Digi Connect Series Benutzerhandbuch

Digi

Digi ConnectPort X4 H Bedienungsanleitung

Digi

Digi TX64 Bedienungsanleitung

Digi

Digi IX10-00G4 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Digi

Digi ConnectPort X2e ZB Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung