Digilock Next Mech Bedienungsanleitung

Installation Guide

Lock Parts

Mounting

Screws

Screw type

M3×10 ✓

0 – 5 mm

✓

M3×145 – 8 mm

M3×108 – 12 mm

M3×1412 – 16 mm

M3×1816 – 20 mm

Mounting plate

Accommodates door

thickness up to 20 mm

Mortise Hole Dimensions

Spacer Requirements

Spacer required* for door

thickness less than 8 mm

Factory default combination 0-0-0-0

Removal keyManager key

Door thickness *Spacer required

77 mm

31.5 mm

min. 6.35 mm

Cam in Locked Position

must overlap Strike

Plate by at least ¼"

(6.35 mm)

Mounting

Screws

Screw type

M3×10 ✓

0 – 5 mm

✓

M3×145 – 8 mm

M3×108 – 12 mm

M3×1412 – 16 mm

M3×1816 – 20 mm

Mounting plate

Accommodates door

thickness up to 20 mm

Mortise Hole Dimensions

Spacer Requirements

Spacer required* for door

thickness less than 8 mm

Factory default combination 0-0-0-0

Removal keyManager key

Door thickness *Spacer required

77 mm

31.5 mm

min. 6.35 mm

Cam in Locked Position

must overlap Strike

Plate by at least ¼"

(6.35 mm)

Mounting

Screws

Screw type

M3×10 ✓

0 – 5 mm

✓

M3×145 – 8 mm

M3×108 – 12 mm

M3×1412 – 16 mm

M3×1816 – 20 mm

Mounting plate

Accommodates door

thickness up to 20 mm Mortise Hole Dimensions

Spacer Requirements

Spacer required* for door

thickness less than 8 mm

Factory default combination 0-0-0-0

Removal keyManager key

Door thickness *Spacer required

77 mm

31.5 mm

min. 6.35 mm

Cam in Locked Position

must overlap Strike

Plate by at least ¼"

(6.35 mm)

Setup

Note: Removing the Programming Key in the circle mark position will remove the core. See Replace Key Set and Core instructions to reinsert the core.

Mounting

Screws

Screw type

M3×10 ✓

0 – 5 mm

✓

M3×145 – 8 mm

M3×108 – 12 mm

M3×1412 – 16 mm

M3×1816 – 20 mm

Mounting plate

Accommodates door

thickness up to 20 mm Mortise Hole Dimensions

Spacer Requirements

Spacer required* for door

thickness less than 8 mm

Factory default combination 0-0-0-0

Removal keyManager key

Door thickness *Spacer required

77 mm

31.5 mm

min. 6.35 mm

Cam in Locked Position

must overlap Strike

Plate by at least ¼"

(6.35 mm)

Assign a User Combination

Once a new user combination is assigned, the previously assigned user combination will no longer operate the lock. If the current user code

is unknown, follow the Reset Combination instructions to ﬁnd the current assigned code then continue to Assign a new User Combination.

1. Set the dial to show the current assigned combination.

2. Insert the Programming Key and turn the knob to the

circle mark position.

3. Set any 4-digit combination.

4. Turn the knob to the locked position and remove the

Programming Key.

5. Scramble the code.

Dial Combo

Assigned Use

Product Guide

Rear UnitFront Unit

Locked Position

Reset Pin Holes

Key Slot

Unlocked Position

Programming

Position

Comibination Dial

Cam

Mounting

Screws

Screw type

M3×10 ✓

0 – 5 mm

✓

M3×145 – 8 mm

M3×108 – 12 mm

M3×1412 – 16 mm

M3×1816 – 20 mm

Mounting plate

Accommodates door

thickness up to 20 mm Mortise Hole Dimensions

Spacer Requirements

Spacer required* for door

thickness less than 8 mm

Factory default combination 0-0-0-0

Removal keyManager key

Door thickness *Spacer required

77 mm

31.5 mm

min. 6.35 mm

Cam in Locked Position

must overlap Strike

Plate by at least ¼"

(6.35 mm)

Operating Instructions

Operate with a Combination

Reset Combination

Operate with a Manager Key

To Lock:

1. Close the door.

2. Turn the knob to the locked position.

3. Scramble the combination.

To Unlock:

1. Enter the assigned 4-digit combination.

2. Turn the knob to the unlocked position.

3. Open the door.

To Unlock with Manager Key:

1. Insert the Manager Key.

2. Turn the knob to the unlocked position.

3. Open the door.

To Lock with Manager Key:

4. Close the door.

5. Turn the knob to the locked position.

6. Remove the Manager Key.

Mounting

Screws

Screw type

M3×10 ✓

0 – 5 mm

✓

M3×145 – 8 mm

M3×108 – 12 mm

M3×1412 – 16 mm

M3×1816 – 20 mm

Mounting plate

Accommodates door

thickness up to 20 mm Mortise Hole Dimensions

Spacer Requirements

Spacer required* for door

thickness less than 8 mm

Factory default combination 0-0-0-0

Removal keyManager key

Door thickness *Spacer required

77 mm

31.5 mm

min. 6.35 mm

Cam in Locked Position

must overlap Strike

Plate by at least ¼"

(6.35 mm)

Note: The Manager key cannot be inserted or removed when the knob is in

the unlocked position.

Note “M” for

Manager on key

Programming Instructions

Dial Combo

Assigned Use

Product Guide

Note “M” on

Manager Key

If the door is locked, use the Manager Key to

open the door.

1. Using the Manager Key, turn the knob to

the locked position.

2. Remove the Manager Key.

Insert the Reset Tool into the four pin holes on

the rear of the unit.

Push in the Reset Tool and simultaneously turn

all dials until they stop.

The ﬁnal code displayed is the current code. In

this example, the combination was 5-9-9-4.

Remove the Reset Tool and turn the knob to

the unlocked position.

Follow instructions to Assign a User Combination.

Reset Tool

Phone: +852 2776 0800

www.digilock.com | [email protected]PG-NLMD-AP-AEN

Support

Mounting screws

Screw type

M3X10 ✓

0 - 5

✓

M3X145 - 8

M3X108 - 12

M3X1412 - 16

M3X1816 - 20

Mounting plate

Accommodates door thickness up to 20mm Through hole dimensions

Spacer required for

door thickness less than 8mm

Factory default code 0-0-0-0

Removal keyManager key

Door thickness (mm) Spacer required

31.50

Programming Key

Does not Unlock with Assigned Combination

The previously assigned combination has not been cleared, follow instructions to Assign a User Combination to set a new combination. If the

currently assigned combination is unknown, see instructions to “Reset Combination”.

Dials do not stop when Using the Reset Tool

The Reset Tool must be inserted ﬁrmly while simultaneously turning the dials. If the dials do not stop try pushing the Reset Tool with more force.

Note “P” for

Programming

on key

Dial Combo

Assigned Use

Product Guide

092419

Replace Key Set and Core

Please contact [email protected]m if your Manager or Programming key(s) are lost or stolen to purchase a new set of keys and replacement

cores for all locks.

If your Manager Key was lost or stolen, you can remove lock cores with your existing Programming key. Once you remove the lock cores, contact

[email protected] to purchase a new set of keys and lock cores.

Turn the knob to the unlocked position. Insert the old Programming Key.

Turn the Knob to the Core Programming

Position. The triangle mark on the Knob will

align with the circle mark on the face.

Pull the Programming Key to remove the old

Knob and Core.

Insert the replacement Programming Key into

the old Knob and place the NEW Core on the

Knob. The triangle mark on the knob should

be aligned with the Raised Wafers.

Insert the new Core subassembly into the lock.

The triangle mark on the Knob will align with

the circle mark on the face.

Turn the knob to the unlocked position.

Remove the Replacement Programming Key.

New Core

Triangle Mark

aligned with

Raised Wafers

Inhaltsverzeichnis

Andere Digilock Sperren Handbücher

Digilock

Digilock DL330BT Bedienungsanleitung

Digilock

Digilock Numeris Versa Standard Bedienungsanleitung

Digilock

Digilock Numeris Versa Bedienungsanleitung

Digilock

Digilock DCK1-APV1 Bedienungsanleitung

Digilock

Digilock numeris aspire Bedienungsanleitung

Digilock

Digilock DCR1-APV1 Bedienungsanleitung

Digilock

Digilock Shared Use RFID Camlock Bedienungsanleitung

Digilock

Digilock DAK1-APS1 Bedienungsanleitung

Digilock

Digilock DAR1-APV1 Bedienungsanleitung

Digilock

Digilock Lockup M Bedienungsanleitung

Digilock

Digilock ATS Bedienungsanleitung

Digilock

Digilock Next Mech Dial Combo Bedienungsanleitung

Digilock

Digilock NEXTLOCK CUE Series Bedienungsanleitung

Digilock

Digilock DK-APS 4G Betriebsanleitung

Digilock

Digilock Curve Bedienungsanleitung

Digilock

Digilock ADA User Key Betriebsanleitung

Digilock

Digilock DAR1-ATS1 Bedienungsanleitung

Digilock

Digilock numeris aspire Bedienungsanleitung

Digilock

Digilock NEXT Sola3 Touch RFID Bedienungsanleitung

Digilock

Digilock DCR1-ATV1 Bedienungsanleitung

Digilock

Digilock Assigned Use RFID Camlock Bedienungsanleitung

Digilock

Digilock NEXT Sola3 Keypad Bedienungsanleitung

Digilock

Digilock NEXT Sola3 Keypad Bedienungsanleitung

Digilock

Digilock Numeris Versa Mini Bedienungsanleitung

Beliebte Sperren Handbücher anderer Marken

Magic

Magic 105 Bedienungsanleitung

Gantner

Gantner GAT NET.Lock 7020 System Kurzanleitung

Wittkopp

Wittkopp Insys 7202 Bedienungsanleitung

Dorma

Dorma Studio Classic Bedienungsanleitung

Securam

Securam ECSL-601 Bedienungsanleitung

Sudhaus

Sudhaus 3003 Bedienungsanleitung

Safety 1st

Safety 1st 48517 Bedienungsanleitung

Pado

Pado FDS-10 Bedienungsanleitung

Esco

Esco systeQ Series Bedienungsanleitung

COMPX

COMPX National D8951 Bedienungsanleitung

secureo

secureo Key Box Bedienungsanleitung

Stock Loks

Stock Loks C8713 Bedienungsanleitung

COMPX

COMPX 1T-058 Betriebsanleitung

Auslock

Auslock T11 Bedienungsanleitung

ELCOM

ELCOM 7205 Bedienungsanleitung

Stealth SAFES

Stealth SAFES ShadowVault Bedienungsanleitung

Knox

Knox KeySecure 5 Bedienungsanleitung

Kwikset

Kwikset 48334/01 Bedienungsanleitung