Digimerge DNB6300V Bedienungsanleitung
HIGH RESOLUTION DUAL-CODEC
HEAVY DUTY VARIFOCAL DAY/
NIGHT BULLET CAMERA
DNB6300V
Q
U
I
C
K
I
N
S
T
A
L
L
A
T
I
O
N
G
U
I
D
E
Page 2
www.digimerge.com
DNB6300V_Quick Installation Guide_En_R1
This installation guide provides instructions for installing the Digimerge DNB6300V High
Resolution Dual-Codec Heavy Duty Varifocal Day/Night Bullet Camera on your network.
For all other aspects of using the product, please refer to the user manual available at
www.digimerge.com or on the Installation CD included with this product.
PACKAGE CONTENTS
IMPORTANT!
This product must be installed in compliance with local laws and regulations.
Package Contents:
1 x High Resolution Dual-
Codec Heavy Duty Varifocal
Day/Night Bullet Camera
1 x Heavy Duty Metal Wall Mount Arm
1 x Mounting Hardware
2 x Security HEX Tools
1 x GPIO Mini-DIN/Terminal
Block Conversion Cable
1 x Software CD with Quick Installation
Guide & Hardware Manual.
1 x hard copies of Quick Installation
Guide, Housing Manual & Warranty Card
1 x 3ft Ethernet Cable
1. Camera Power Input Port
2. Power/Network Status LED Indicators
3. Ethernet Port
4. GPIO Port (Optional Connection)
1 2 3 4
To access the ports on the Camera, the lid
must first be lifted (by unscrewing the 2
holding screws using the large Hex tool).
Connector Ports:
12 3 4
1. Cooling Fan Power Cable
2. IR Sensitivity Adjustment
3. Hard Wired Power Terminal Block
4. IR LED Power Terminal Block
DNB6300V_Quick Installation Guide_En_R1
www.digimerge.com
Page 3
• Hardware installation:
A. Powered Install
B. Optional GPIO Connections
C. Adjusting the Included Lens
• Software installation
• Network configuration
HARDWARE CONNECTIONS
1
Hardware Installation - Powered Install
The basic Hardware installation consists of
mounting the camera and stand, connecting the
hard wired power and connecting the Ethernet cable
to the Camera. Other connections are optional.
NOTE: The cables should be run through the wall or
ceiling to the mounting location, prior to installing
the Camera.
1. Mounting Instructions: Run the Power and
Ethernet cables to the desired location.
• Cut out the cable channel hole in the Rubber
stopper. Place the stopper on the stand.
• Run the cables from the wall and through the
stand before permanently mounting the stand
to the wall or ceiling.
• Mount the stand to the wall or ceiling using the
provided screws.
• Securely connect the camera housing to the
stand.
A
1
Page 4
www.digimerge.com
DNB6300V_Quick Installation Guide_En_R1
HARDWARE CONNECTIONS
1
Continued
2. Use the provided HEX tool to loosen the screws on
the top of the camera housing. Open the lid to
access the ports.
NOTE: Make sure the Power and Ethernet Cables have
been passed through the stand and into the housing
before proceeding.
3. Power: Connect a CSA/UL approved 3 Conductive
Wire Power Cable (not provided) to the 3 terminals
on the far left of the Power Terminal Block as shown:
• Loosen the 3 screws with a screwdriver.
• Connect the wires to the labelled ports (Live,
Earth and Neutral).
• Tighten the screws to hold the wires in place.
NOTE: Please refer to the included INFRARED
ILLUMINATOR HOUSING insert or Hardware Manual
for additional installation details.
4. Network: Connect the network cable to the Camera
Ethernet Cable (Port).
NOTE: CAT-5 Ethernet Cabling has a maximum
effective range of 100m (330 ft.) depending on the
cable/switcher quality. For a longer run, a repeater
device may be required.
To test the video feed locally from the Camera, tem-
porarily connect the GPIO Connector to the Camera
(see Section B) and use the BNC Connector to connect
to a local TV or Monitor (a BNC/RCA Adaptor may be
required).
2
3
4
DNB6300V_Quick Installation Guide_En_R1
www.digimerge.com
Page 5
Hardware Installation - GPIO Connections
The Optional Connection includes the use of the
GPIO Cable for analouge video capture, Alarm
and/or PTZ Control.
• Feed the wires for the desired control into the
Camera through the stand.
• Connect the GPIO Cable to the GPIO Port
located to the right of the Ethernet Cable
Connection.
• Connect the wires to the GPIO Terminal block
inside the camera housing. Tuck the GPIO
terminal block below the bracket once
complete.
NOTE: The GPIO Terminal Block is color coded
and labelled. Please see Appendix #2 of the hard-
ware manual for Alarm Block connections.
HARDWARE CONNECTIONS
1
B
Continued
4i 4ii
Hardware Installation - Adjusting the Included
Lens
• Use the ZOOM and FOCUS controls on the front
of the attached lens to adjust:
FOCUS - Adjust the lens to make the image
appear sharp and well defined once the varifocal
distance has been set.
ZOOM - Increase or Decrease the viewing
distance for the camera image (adjust the varifocal
distance between 7.5~50mm)
NOTE: Once all internal connections have been
made, set the desired angle for the camera and
secure the tightening screw on the camera base.
Replace the cover and tighten the screws with the
HEX tool.
C
Focus Zoom
GPIO Port
GPIO Terminal
Block
OPTIONAL
Page 6
www.digimerge.com
DNB6300V_Quick Installation Guide_En_R1
SOFTWARE INSTALLATION
2
The Digiconsole application loads
from the CD included with your
package, and provides you with the
following:
1. Web links to various resources
and documentation
2. Discovery of all the Digimerge
IP devices on the network
3. Provides Network
configuration of IP Devices
4. Installs DigiConsole and
Surveillance application on your
local PC
5. Warranty information and DDNS
registration
A
Digiconsole Utility screen consists of
the following menus:
1. Home
2. Find Devices
3. Register
4. Install
B
DNB6300V_Quick Installation Guide_En_R1
www.digimerge.com
Page 7
Home:
Provides basic Digiconsole operating
instructions, links to product informa-
tion/documentation as well as 3rd party
software support links.
SOFTWARE SET-UP
A
Find Devices:
Locates all available Digimerge IP
devices on your network and displays
a snapshot of the results. Click on any
available device to display image on
the right side screen display.
NOTE: You may need to press the Find
Devices button several times as some
devices may not respond immediately.
If you do not see a camera image,
please check that all cables running
from the Camera are connected
properly.
B
C
Menu:
The Menu Button or right clicking on
a device icon provides access to
device specific settings:
• Edit Network Parameters
• View Live Image
• Open Device in Browser
• Update Firmware in Video Device
• Refresh the device list - in order to
remove inactive and disconnected
devices
NOTE: It is recommended that you
record the device specific MAC and
IP address for DDNS registration
purposes. If you have multiple
cameras on a local network, only
one camera needs to be configured
for DDNS.
3
MAC:
IP:
Page 8
www.digimerge.com
DNB6300V_Quick Installation Guide_En_R1
SOFTWARE SET-UP
Edit Network Parameters:
The Network Parameters are
automatically assigned to the
Device by the network router (by
using DHCP). These settings can
be manually changed if desired.
1. Select the IP device you would
like to edit by clicking on its icon.
2. Click on the MENU button or
right click the icon for the device
to access the menu. Select
“Edit Network Parameters” from
the menu.
3. Make the necessary changes
and click OK to save changes or
click CANCEL to close the
window without saving any of the
changes made.
NOTE: If a user name and password
were set-up on the IP Device previ-
ously, you will be required to enter
this authentication information when
attempting to access the device.
C1
Continued
View Live Image:
View live video from the IP Device
using the Apple Quicktime program.
If this application is not installed on
your system, please download it (no
charge) at
http://www.apple.com/quicktime
C2
3
OPTIONAL
If by clicking VIEWING LIVE IMAGE
the image is not automatically shown
in Quicktime, follow these steps in
Quicktime:
1. Go to FILE
2. Choose OPEN URL
3. Enter the following: rtsp://<device
IP address> (i.e. rtsp://192.168.2.102)
A device IP address can be obtained
from the Digiconsole device list.
NOTE: Minimum Quicktime version installed
should be 7.1.6. If you cannot install Quick-
time, use Microsoft Internet Explorer to view
the device. See step C3 for details.
DNB6300V_Quick Installation Guide_En_R1
www.digimerge.com
Page 9
SOFTWARE SET-UP
Continued
Open Device in Browser:
Opens up the DigiViewer Video Browser
using your default web browser (e.g.
Internet Explorer).
The DigiViewer browser allows the user
to view streaming video from the device
as well as change certain settings on the
device depending on the level of access
set by the administrator.
C3
3
Once user names and passwords are set
up by the administrator, the users (except
for a VIEWER level user) are required to
enter this information every time they ac-
cess the DigiViewer.
Click (during streaming mode)
to mute the audio.
Click to capture a snapshot image
in a new browser window.
By default, the image refresh rate
is set to OFF. Move slider to the
right to set image refresh rate.
Click to bring up image brightness and contrast controls
Click to capture a video clip and send it to a FTP site. FTP
must be configured in the SETTINGS screen
Click here to start streaming video
Page 10
www.digimerge.com
DNB6300V_Quick Installation Guide_En_R1
SOFTWARE SET-UP
3 Levels of User Access:
• Administrator (current user)
• Operator (general user)
Default User Name: guest
Password:<leave blank>
• Viewer (anonymous guest)
Creating Current User Account:
1. Click SETTINGS
2. Select ACCOUNTS
3. Fill in a user name and
password in the assigned fields
4. Reconfirm password
5. Click UPDATE ACCOUNTS
1. Administrator: Administrator has
unrestricted access to all the
settings of the device. The
interface will only permit creation
of ONE administrator account.
2. Operator: Operator has restricted
access to the settings of the
server. The interface will only
permit creation of FIVE operator
accounts.
Note: Restrictions - View images.
Requires username and password.
3. Viewer: The interface will permit
the creation of ONE viewer
account (i.e. Anonymous Guest).
This account does not require a
password.
Note: Viewer Restrictions - View im-
ages if permission is granted by ad-
ministrator. Note that the permission
in this case refers to providing the
IP address to someone. Whomever
receives the IP address can view the
camera remotely as a anonymous
guest. No password is required.
Multiple users can access the de-
vice at the same time, however this
will limit the quality and speed of the
video as the feed is shared between
all connected users.
Continued
3
Andere Handbücher für DNB6300V
1
Inhaltsverzeichnis
Andere Digimerge Sicherheitskamera Handbücher
Digimerge
Digimerge Flir DBV44TL Bedienungsanleitung
Digimerge
Digimerge DCBHR1037 Bedienungsanleitung
Digimerge
Digimerge DPV14D Bedienungsanleitung
Digimerge
Digimerge DCB13TL Bedienungsanleitung
Digimerge
Digimerge DNP5320E Bedienungsanleitung
Digimerge
Digimerge DPV24D Bedienungsanleitung
Digimerge
Digimerge DPB14TLX Bedienungsanleitung
Digimerge
Digimerge DCV13TL Bedienungsanleitung
Digimerge
Digimerge DPD23D Bedienungsanleitung
Digimerge
Digimerge DPV34D Bedienungsanleitung
Digimerge
Digimerge DPV24D Bedienungsanleitung
Digimerge
Digimerge DCBHR1535 Bedienungsanleitung
Digimerge
Digimerge DPV14D Bedienungsanleitung
Digimerge
Digimerge DPP12D Handbuch
Digimerge
Digimerge DPZ16TO27 Bedienungsanleitung
Digimerge
Digimerge DCV54DL Bedienungsanleitung
Digimerge
Digimerge DPD14T Bedienungsanleitung
Digimerge
Digimerge DPZ36WO23 Bedienungsanleitung
Digimerge
Digimerge DPV34WL Handbuch
Digimerge
Digimerge DCBHR1035 Bedienungsanleitung
