Digimerge DPV24D Bedienungsanleitung
Please read this manual thoroughly before use and keep it handy for future reference.
Vandal Models: DPV24D / DPV24TLX
Indoor Models: DPD23D / DPD24D
Ultra Resolution
Day & Night Dome Camera
INSTRUCTION MANUAL
INTRODUCTION
Features
All Models Feature:
• 1/3”SonySuperHAD™IICCD
• Excellentlowlightperformanceusing
PolarisVision2technology.
• 0.15Lux/F1.2(Color)
0.001Luxw/Sense-Upatx256
• 600TVlines(Color)ofresolution
• 3DDigitalNoiseReduction(3D-DNR)
• OSDmenucontrol
• PrivacyMasking/MotionDetection
• VIDEOOUT(BNC)
• Operatesin12VDCor24VAC
• TestMonitorOutput
• CameraMounting:Surface/Flushmounting
(IndoorModelonly)
DPD23D
• IndoorDomeModel
• 3.6mmFixedLens
DPD24D
• IndoorDomeModel
• 2.8-10.5mmVarifocalDay/NightLensF1.4DCIris
DPV24D
• VandalResistantDomeModel
• 2.8-10.5mmVarifocalDay/NightLensF1.4DCIris
DPV24TLX
• VandalResistantDomeModel
• 2.8-10.5mmVarifocalDay/NightLensF1.4DCIris
• SmartIRtechnology
• ICRltertogiveclearnightvision
• ArcticProtechnologywithbuilt-inheater
• 0LuxwithIRLED
General DPD23D DPD24D DPV24D DPV24TLX
Power source DC 12V / AC 24V +10%
Power consumption 2.5 Watts 10 Watts
(Heater On)
Image sensor 1/3”SonySuperHAD™IICCD
Total pixels 811 (H) x 508 (V)
Scanning system 2:1 interlace
Scanning frequency 15.734KHz(H), 59.95Hz(V)
Sync.system Internal / Line Lock
Resolution 600 TV Lines
Min.Illumination 0.15Lux / 0.001Lux
Sense Up at x256 0 Lux IR LED On
Video output 1.0 Vp-p (75 ohm, composite)
S/N Ratio more than 50dB (AGC OFF)
Operating Temperature -10°C - +50°C -40°C - +50°C
Power input 2-Pin terminal block (Detachable)
Video output BNC Connector (2nd video RCA)
Lens mount Fixed mount
Lens 3.6mm Fixed 2.8 - 10.5mm F1.4 Varifocal DC Auto iris
Operating humidity 0-90% (non-condensing)
SPECIFICATIONS
-1-
-2-
MEASUREMENTS
Vandal Dome Dimensions
3/4’’ -14
NPS thread
97.0 mm
3.82 in
Base hole positions
40 mm
1.57 in
55.5 mm
2.19 in
Ø 0.1"
3.5 mm
3.9"
100.0 mm
3.4"
87 mm
5.1"
130 mm
112 mm
4.4 in
112 mm
4.4 in
39 mm
1.5 in
115 mm
4.5 in
27 mm
1.1 in
137°
123°
100°
7 mm
.28 in
Underside Base hole positionsIndoor Dome Dimensions
Recess cutout and tting clearance.Recess Mount Fitting dimensions
5.1"
130 mm
-3-
PACKING CONTENTS
Indoor Dome package contains the following:
Camera in housing ---------------------------------1
Camera Locking screws (PA3 Type) -----------2
Instruction guide (This Document)-------------1
Surface & Flush Mounting Templates----------2
RCA - BNC test cable------------------------------1
Junction Box Plate----------------------------------1
Mounting screw pack ------------------------------1
Vandal Dome package contains the following:
Camera in housing ---------------------------------1
Camera Locking screws (PM4 Type) ----------3
Instruction guide (This Document)-------------1
Surface Mounting Template ----------------------1
RCA - BNC test cable------------------------------1
Junction Box Plate----------------------------------1
Mounting screw pack ------------------------------1
Tamper allen key------------------------------------1
Conduit Key ------------------------------------------1
Junction box plate allows tting of either Vandal dome or
Indoor dome to standard 2S, 4S and Octagon junction
boxes.
NOTE: Flush side of junction box plate should be attached
to junction box
Junction Box tting plate accessories:
Junction Box Fitting plate ------------------------1
2S / 4S plate screws (KM3.5 Type) ------------4
Octagon tting screws (KM4 Type)-------------2
Base Fitting Screws PWM3 ----------------------3
JUNCTION BOX PLATE
Screw hole overview Vandal dome tting illustration Junction box tting plate attached to camera
Base Fitting
Screws
88.9 mm
3.5 in
83.3 mm
3.28 in
46.0 mm
1.8 in
Base Fitting
Screw.
Octagon
Screw
2S / 4S
Screw
Locking
Screw
Conduit
Key
Allen Key
Mounting Screws Pack.
3pc 70mm / 2.8in Screws
3pc 30mm / 1.2in Screws
3pc 40mm 1.6in plugs
-4-
JUNCTION BOX INSTALLATION TYPES
2S FITTING
a. 2S Fitting requires only 2pcs of base
attachment screws.
Note: You have a reduced space in which
to hide cables using this type of
installation. Recommended for indoor
dome only.
TWO GANG FITTING
a. Two gang tting (switch box) requires 4pcs
of base attachment screws.
Note: A two gang provides the most robust
tting. Suitable for both indoor and
vandal domes.
4S FITTING
a. 4S Fitting requires 2pcs of base attachment
screws.
Note: Screws used for the 4S box are larger
compared to those used for the 2S (M4
type). Suitable for both indoor and
vandal domes
OCTAGON FITTING
a. 4” Octagon tting requires only 2pcs of
base attachment screws.
Note Screws used for the octagon tting
are larger compared to those used for
the 2S/4S (M4 type). Suitable for both
indoor and vandal domes
Cable
Entry
Screws
Cable
Entry
Screws
Cable
Entry
Screws
Cable
Entry
Screws
-5-
VANDAL DOME FITTINGS
Pendant Cap - model # MNTV2XPC
Replaces the need for the camera base.
Compatible with ceiling conduit installations
Pole Mount - model # MNTV2XPJunction Box Accessory - model # MNTV2XJ
Fits either wall mount and corner mount bracket.
Symmetrical so reversible for top or bottom
conduit.
Corner Mount bracket - model # MNTV2XR
Can t either Wall Bracket or Junction Box. Pendant Mount - model # MNTV2XC
Wall Mount - model # MNTV2XW
-6-
INSTALLATION. VANDAL DOME
1) Remove the three tamper screws using the provided
allen key. Size is standard T-15
Note: If you plan to use conduit tting, remove conduit
cap using the prodivded conduit key.
DPV24TLX ONLY
When using DC power, note the correct polarity stated on the
label attached to the power cord.
Note: If you plan on installing onto a junction
box, attach provided tting plate rst to
the junction box and then you attach the
camera base to the tting plate.
3a) Reinsert camera module into camera base
by ligning up the arrow notches, and turning
camera module clockwise to lock into place.
3b) Use the supplied three base locking screws to
secure camera base to camera module.
Go to step 4on page 7 to complete installation.
Method 1 - Direct Attach Install
2a) Use included mounting template to mark and pre-
drill the required holes. Use 2pc of the 2.8” screws
to mount the camera directly to the mounting
surface.
Remove (one base locking screw, used for shipping
purposes) and install the 3rd 2.8” screw.
Go to step 4on page 7 to complete installation.
OR
Method 2 - Camera Base Install
Note: Use this method if installing onto junction box
plate.
2b) Remove the camera base by unscrewing the base
locking screw, and turn camera module approx. 5
degrees counter-clockwise to detach camera base
from the camera module. Now you install the base
to the correct holes as indicated on the mount
template using the 1.2” screws.
1
3
a
b
a
b
2
Andere Handbücher für DPV24D
3
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere Digimerge Sicherheitskamera Handbücher
Digimerge
Digimerge DBD14 Bedienungsanleitung
Digimerge
Digimerge DPV24D Bedienungsanleitung
Digimerge
Digimerge DCBHR1535 Bedienungsanleitung
Digimerge
Digimerge DCBHR1035 Bedienungsanleitung
Digimerge
Digimerge DPV34WL Handbuch
Digimerge
Digimerge DPV24D Bedienungsanleitung
Digimerge
Digimerge DCV54DL Bedienungsanleitung
Digimerge
Digimerge DPV24DL Bedienungsanleitung
Digimerge
Digimerge DPV24D Bedienungsanleitung
Digimerge
Digimerge DPV14D Bedienungsanleitung
Digimerge
Digimerge DCDHR2532 Bedienungsanleitung
Digimerge
Digimerge DPV34D Bedienungsanleitung
Digimerge
Digimerge DPV24DL Bedienungsanleitung
Digimerge
Digimerge DPZ36WO23 Bedienungsanleitung
Digimerge
Digimerge DCV24DL Bedienungsanleitung
Digimerge
Digimerge DPZ16TO27 Bedienungsanleitung
Digimerge
Digimerge DCV13TL Bedienungsanleitung
Digimerge
Digimerge DPV14D Bedienungsanleitung
Digimerge
Digimerge DCS100033 Bedienungsanleitung
Digimerge
Digimerge DCBHR1535 Bedienungsanleitung
