Digisol DG-GR6010 Bedienungsanleitung
V1.0
2019-9-12
XPON ONU Router with
1 PON and 1 Giga Port
DG-GR6010
Copyright 2019 by DIGISOL SYSTEMS LTD. All rights reserved.
Company has an on-going policy of upgrading its products and it may be
possible that information in this document is not up-to-date.
Please check with your local distributors for the latest information.
No part of this document can be copied or reproduced in any form without
written consent from the company.
Trademarks:
TM
DIGISOL is a trademark of DIGISOL SYSTEMS LTD. All other trademarks
are the property of the respective manufacturers.
Copyright
Figure 1
1:2 Application Chart
DG-GR6010 ONU meets telecom operators FTTO (office), FTTD (Desk),
FTTH (Home) broadband speed, SOHO broadband access, video
surveillance and other requirements to design an GEPON / GPON Ethernet
network. It is based on mature and stable, cost-effective EPON & GPON
technology. It is highly reliable, easily manageable, provides configuration
flexibility and good quality of service (QoS) guarantees. They are fully
compliant with GPON and EPON technical regulations such as ITU-T
G.984.x & IEEE802.3ah. Dual mode ONU can detect and exchange PON
mode automatically.
1:1 Product Description
Overview
Figure 2
1:3 Technical Parameters
Parameter Name EPON GPON
PON SC single-mode/ SC single-mode/
single-fiber. single-fiber.
Symmetric 1.25Gbps. Uplink 1.25Gbps,
downlink 2.5Gbps
Wavelength Tx 1310nm, Rx 1490nm
Sensitivity <-28dBm(PX20+) <-28dBm(CLASS B+)
Overload >-3dBm(PX20+) >-8dBm(CLASS B+)
Optical Type SC/UPC
Interface Type 1*10/100/1000Mbps
Auto adaptive Ethernet interfaces, Full/Half Duplex,
RJ45 connector
Indicators 3, For SYS, LINK/ACT, REG.
Ambient temperature -30 ~ +70 °C
Ambient humidity 10% ~ 90% (non-condensing)
Store temperature -30 ~ +70 °C
Store humidity 10% ~ 90% (non-condensing)
Dimension(L x W x H) 82mm×82mm×25mm
Power 12V,0.5A
Power Consumption ≤4W
Gross weight Around 230g
1:4 Package Content
Contents Quantity
ONU 1 PCS
Power Adapter 1 PCS
QIG 1 PCS
To avoid equipment damage caused by improper use and personal injury,
please observe the following precautions:
● Do not place the device near water or in damp places, in order to
prevent water or moisture from entering the device.
● Do not place the device in an unstable place, avoid falling damage to
equipment.
● Make sure that the supply voltage of the device matches the required
voltage value.
● Do not open the equipment chassis without permission.
● Unplug before cleaning the power plug; prohibit the use of liquid cleaning.
Installation Environment Requirements
ONU equipment must be installed in the interior and ensure the following
conditions are meet:
● Confirmation at the ONU installation site to have sufficient space to
facilitate cooling machine.
● ONU suitable operating temperature of -10 ~55 , °C °C
humidity 10% to 90%.
Electromagnetic Environment
ONU equipment in use can be affected by external electromagnetic
interferences, such as radiation and conduction through the impact on the
device, this should note the following:
● Device workplace should avoid radio transmitters, radar stations, and
high-frequency interference from power equipment.
● Users cable typically require alignment indoors if outdoor lightning
traces measures should be taken.
Equipment Installation
ONU product is a fixed configuration cassette equipment, site equipment
installation is relatively simple. Simply install the device on a specified place,
connecting the upstream fiber subscriber line connections, connect the
power cable. Actual operation is as follows:
2:1 Installation Requirements
Installation
1. Installed on the desktop
Place the machine on a clean bench, this installation is relatively simple,
you can observe the following operation:
● Ensure the smooth workbench.
● There should be enough space around the device for heat dissipation.
● Do not place objects on the device.
2. Mounted on the wall
● Observation ONU equipment chassis consist two cruciform recess, in
accordance with the position of the groove, installed two screws in the
wall.
● The original selected two mounting screws gently snap into recesses
aligned.
● Slowly let go, so that the device under the support of the screw
hanging on the wall.
2:2 Panel Lights
LED Mark Status Description
Registration REG
On and
Green in
colour
The device is registered to the PON system
Off / Red
in colour
Device is not registered to the PON system
Blink Device registration is incorrect
Fast Blink Port is sending or/and receiving data
Interface LINK/
ACT
On Port is connected properly (LINK)
Off Port connection exception or not connected
Blink Port is sending or/and receiving data (ACT)
System SYS
On / Off System is not running or fatal error
Blink Normal running
The following is the default device configuration information.
● Local (LAN access) Username: admin / Password: admin
● LAN port management IP address: 192.168.1.1/24
3:1 Default configuration
Web Management
DG-GR6010 provides simple Web management functions including Device
Information, modification of LAN Management IP address, LOID and
Password, Configuration File Backup and Restore, Firmware Upgrade etc...
NOTE:
Detailed ONU Configuration is possible via CTC OAM Protocols on the OLT.
Figure 3 Web Login
3:2 Default configuration
Web login default username: admin, password: admin
Figure 4 Device Information
Device Info Menu displays the current device base informations,
including Hardware Version, Software Version, Boot Loader Version.
Note:
1. All the device information may be changed, the received device shall
prevail.
Figure 5 Modify Loid and Password
LOID Menu displays the current device LOID and Password informations.
LOID: 0-24 bytes. Password: fixed 10 bytes.
Note:
1. Usually no need to modify the Version and Vendor Product Code
information, otherwise it may lead to ONU registration problems.
2. All the changes to take effect in the equipment after the restart.
Figure 6 Reboot/ Restore Default
Reboot: The operation to reboot the device.
Restore Default: The operation to restore the device to its factory
configuration.
Note:
1. Pressing the RST button for 10 seconds or more will reset the ONU to
its default settings.
2. Pressing the RST button for a shorter duration will simply reboot the
ONU.
Andere Handbücher für DG-GR6010
1
Inhaltsverzeichnis
Andere Digisol Netzwerk-Router Handbücher
Digisol
Digisol DG-GR1010 Bedienungsanleitung
Digisol
Digisol DG-BG1100U Bedienungsanleitung
Digisol
Digisol DG-GS1500E series Programmierhandbuch
Digisol
Digisol DG-GS4528S Bedienungsanleitung
Digisol
Digisol DG-HR1400 Bedienungsanleitung
Digisol
Digisol DG-IS4512HP Bedienungsanleitung
Digisol
Digisol DG-HR1160M Bedienungsanleitung
Digisol
Digisol DG-GS1512HP Bedienungsanleitung
Digisol
Digisol RANGER SERIES Bedienungsanleitung
Digisol
Digisol DG-HR1400 Bedienungsanleitung
Digisol
Digisol DG-BG100 Bedienungsanleitung
Digisol
Digisol DG-FS4528E Bedienungsanleitung
Digisol
Digisol DG-BR5411QAC Bedienungsanleitung
Digisol
Digisol DG-HR1060MS Bedienungsanleitung
Digisol
Digisol DG-LB1054UV Bedienungsanleitung
Digisol
Digisol DG-BG1100U Bedienungsanleitung
Digisol
Digisol DG-FS1526HP Bedienungsanleitung
Digisol
Digisol DG-BR5411QAC Bedienungsanleitung
Digisol
Digisol DG-HR1400 Abmessungen
Digisol
Digisol DG-FS4510 Bedienungsanleitung
Beliebte Netzwerk-Router Handbücher anderer Marken
NETGEAR
NETGEAR FS526T - Switch Bedienungsanleitung
Korenix
Korenix JetNet 5710G Series Bedienungsanleitung
Automated Logic
Automated Logic ZN551 Betriebsanleitung
Cisco
Cisco ASR 1000 Series Bedienerhandbuch
EnGenius
EnGenius ESR-9710 Bedienungsanleitung
Cisco
Cisco 805 Series Bedienungs- und Sicherheitshinweise