Digisol DG-GS1510PL Bedienungsanleitung

V1.0

2019-01-24

8 Port Gigabit Web Managed PoE

Switch with 2 Giga SFP Ports

DG-GS1510PL

PORTS

Trademarks:

Company has an on-going policy of upgrading its products and it may be

possible that information in this document is not up-to-date.

Please check with your local distributors for the latest information.

No part of this document can be copied or reproduced in any form without

written consent from the company.

DIGISOL is a trademark of DIGISOL SYSTEMS LTD. All other trademarks

are the property of the respective manufacturers.

This is a Gigabit Web Managed POE Switch, It provides 8 10/100/

1000Mbps Auto-Negotiation RJ45 POE ports and 2 Gigabit SFP Ports. It

supports the port's full line speed forwarding to ensure the stable

transmission of data. The machine can be used as a small local core switch

or a small and medium-size LAN switch, also can be used as an access

switch for large LAN. It can be widely used in monitoring, wireless, Internet

cafe and other fields.

Grounding: use specialized ground lead connect

Connect the power adapter output terminal to this port. Supports input

voltages +44 ~ +57 VDC

PWR LED：The Power LED lights up when the Switch is connected to a

power source.

Link/Act LED: The Link/Act LED will flash which indicates a network link

through the corresponding port. Blinking indicates that the Switch is either

sending or receiving data to the port.

PoE LED:

Green: Indicates the PoE powered device (PD) is connected and the port

supplies power successfully.

Light off: Indicates no powered device (PD) connected.

RST: By pressing the Reset button for 5 seconds the switch will change

back to the default

configuration and all changes will be lost.

Products Introduction

Front Panel

8 Port 10/100/1000Base-TX with 2 Gigabit SFP and 8 PoE L2+ Managed Switch

Rear Panel

Warning: The SFP ports should use UL listed Optical

Transceiver product, Rated Laser Class I. 3.3Vdc.

Product Features

Conforms to IEEE802.3, IEEE 802.3u, IEEE 802.3ab

Provides 8 10/100/1000 Base-TX ports and 2 1000Base-X SFP ports

High back-plane bandwidth 20Gbps

Support standard IP/ Extend IP / MAC IP / ARP ACL

IGMP snooping and IGMP Query mode for Multimedia application

Port mirror and bandwidth control

IEEE802.3x Full-Duplex Flow control

Support Port Based VLAN / 802.1Q Tag VLAN

IEEE802.3ab Link aggregation

Support IEEE802.3ad Port trunk with LACP

Support Spanning tree protocol IEEE 802.1d

Supports IEEE 802.1p class of service

Support IEEE 802.1x user authentication

Support Broadcast storm filter

Support System event log

Management by Web/SNMP/Telnet

Support IEEE802.3af and 802.3at

This chapter provides unpacking and installation information for the

Managed PoE switch.

Open the shipping carton and carefully unpack its contents. Please consult

the packing list located in the User Manual to make sure all items are present

and undamaged. If any item is missing or damaged, please contact the local

re-seller for replacement.

- Switch 1pcs

- AC power cord 1pcs

- Rubber feet 4pcs

- Screws 6pcs

- Mounting brackets 2pcs

- CD

If any item is found missing or damaged, please contact the local re-seller

for replacement.

Hardware Installation

First step: Open a seal

For safe switch installation and operation, it is recommended that you:

- Visually inspect the power cord to see that it is fully secured to the AC

power connector.

- Make sure that there is proper heat dissipation and adequate ventilation

around the switch.

- Do not place heavy objects on the switch.

attach the mounting brackets in to the switch's side panels (one on each

side) and secure them with the screws provided (please note that these

brackets are not designed for palm size switches).

Second step: Switch installation

Rack installation

When installing the switch on a desktop or shelf, the rubber feet included

with the device must be attached on the bottom at each corner of the

device's base. Allow enough ventilation space between the device and the

objects around it.

Desktop or Shelf Installation

Using the AC power cord to connect to the power adapter, and then plug in

output terminal of the adapter into the DC IN socket on the back of the

switch. (The AC power outlet should be grounded)

Third step: Connecting power supply

Warning: Do not turn on the power switch before

power cables are connected. Power surge may

cause damage to the Switch.

Warning: The installation instructions clearly

state that the ITE is to be connected only to PoE

networks without routing to the outside plant.

As a precaution, the switch should be unplugged in case of power failure.

When power is resumed, plug back the switch again.

Power failure

This chapter introduces the management interface of Managed PoE switch.

Management Option

The Managed PoE switch can be managed through any port on the device

by using the Web-based management.

Each switch must be assigned its own IP address, which is used for

communication with Web-Based Management or a SNMP network manager.

The PC should have an IP address in the same range as the switch.

Please refer to the following installation instructions for the Web-based

Management .

After a successful physical installation, you can configure the Switch,

monitor the network status, and display statistics using a web browser.

The embedded Web-based Management currently supports the following

web browsers:

Internet Explorer 6 or higher version

Netscape 8 or higher version

Mozilla

Firefox 1.5/2.0 or higher version

You will need the following equipment to begin the web configuration of your

device:

A PC with a RJ-45 Ethernet connection

A standard Ethernet cable

Connect the Ethernet cable to any of the ports on the front panel of the

switch and to the Ethernet port on the PC.

3. Getting Started

Using Web-based Management

Supported Web Browsers

Connecting to the Switch

Network connection

In order to login and configure the switch via an Ethernet connection, the PC

must have an IP address in the same subnet as the switch. For example, if

the switch has an IP address of 192.168.0.1, the PC should have an IP

address of 192.168.0.x (where x is a number between 1 ~ 254), and a

subnet mask of 255.255.255.0 Open the web browser and enter

192.168.0.1 (the factory-default IP address) in the address bar.

Then press <Enter>.

To log in to the switch, the IP address of your PC should be set in the same

subnet as that of the switch. The IP address is 192.168.0.x (”x” is any

number from 2 to 254). Subnet Mask is 255.255.255.0.

NOTE: The switch's factory default IP address is

192.168.0.1 with a subnet mask of 255.255.255.0

Enter the IP address in the web browser

1. Logon Dialog Box

When the following logon dialog box appears, enter the password then

click OK.

By default, the username is admin and the password is admin.

After a successful login, the main page will appear as follows, and you can

click the menu on the left side to configure the corresponding functions.

4. WEB page Introduction

Configuration window

Andere Handbücher für DG-GS1510PL

Inhaltsverzeichnis

Andere Digisol Schalten Handbücher

Digisol

Digisol DG-GS4824F Bedienungsanleitung

Digisol

Digisol DG-GS4600 SERIES Bedienungsanleitung

Digisol

Digisol DG-GS4900 SERIES Bedienungsanleitung

Digisol

Digisol DG-GS1528 Bedienungsanleitung

Digisol

Digisol DG-GS1016D-A Bedienungsanleitung

Digisol

Digisol MUSTANG 4000 DG-FS4528 Bedienungsanleitung

Digisol

Digisol DG-GS1510HPEV2 Handbuch

Digisol

Digisol DG-FS1526HP Bedienungsanleitung

Digisol

Digisol DG-GS4528SE Programmierhandbuch

Digisol

Digisol DG-GS4110 Bedienungsanleitung

Digisol

Digisol DG-FS1526 Bedienungsanleitung

Digisol

Digisol DG-CS4616F Bedienungsanleitung

Digisol

Digisol DG-GO4300 Series Bedienungsanleitung

Digisol

Digisol DG-GS1010PF-B Bedienungsanleitung

Digisol

Digisol DG-GS4600SE2 Series Bedienungsanleitung

Digisol

Digisol DG-GS1526 Bedienungsanleitung

Digisol

Digisol DG-GS1528HP/C Bedienungsanleitung

Digisol

Digisol DG-GS1510PL Bedienungsanleitung

Digisol

Digisol DG-GS1510HPEV2 Bedienungsanleitung

Digisol

Digisol DG-GS4526P Bedienungsanleitung

Digisol

Digisol DG-GS1550 Programmierhandbuch

Digisol

Digisol DG-FS1510HPE Bedienungsanleitung

Digisol

Digisol DG-FS4526 Programmierhandbuch

Digisol

Digisol DG-GS1528HP Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung