Digital Equipment InfoServer 150 Bedienungsanleitung

InfoServer150

InstallationandOwner’sGuide

Order Number: EK–INFSV–OM–001

This manual describes how to install, test, operate, and maintain the

InfoServer 150 system.

Digital Equipment Corporation

Maynard, Massachussets

October 1991

The information in this document is subject to change without notice and should not be

construed as a commitment by Digital Equipment Corporation. Digital Equipment Corporation

assumes no responsibility for any errors that may appear in this document.

The software described in this document is furnished under a license and may be used or copied

only in accordance with the terms of such license.

No responsibility is assumed for the use or reliability of software on equipment that is not

supplied by Digital Equipment Corporation or its afﬁliated companies.

The following are trademarks of Digital Equipment Corporation: DEC, DECnet, DECconnect,

DIGITAL, ULTRIX, VAX, VAXserver, VAXstation, VMS, VT, and the Digital logo.

The following are third-party trademarks:

Intel is a registered trademark of Intel Corporation.

MS–DOS is a registered trademark of Microsoft Corporation.

PostScript is a registered trademark of Adobe Systems Incorporated.

Xerox is a registered trademark of Xerox Corporation.

ZK5900

This document is available on CDROM.

This document was prepared using VAX DOCUMENT, Version 2.0.

Contents

Preface ..................................................... vii

1 InfoServer 150 System Overview

1.1 System Highlights . ................................... 1–2

1.2 Storage Devices . . . ................................... 1–3

1.2.1 Internal RZ Hard Disk . . . ........................... 1–3

1.2.2 RRD42 Compact Disc Drive .......................... 1–3

1.3 Console Terminal . . ................................... 1–4

2 Installing Your System

2.1 Choosing the Right Location for the System ................ 2–1

2.2 Unpacking and Inspecting System Components .............. 2–2

2.3 Connecting System Components ......................... 2–4

2.3.1 Identify the System Unit Ports and Connectors . .......... 2–4

2.3.2 Install the SCSI Terminators ......................... 2–5

2.3.3 Install the Connector Covers ......................... 2–5

2.3.4 Attach the Ethernet Terminators . . . ................... 2–6

2.3.5 Connect the System Unit Power Cord .................. 2–9

2.3.6 Connect a Console Terminal .......................... 2–10

2.3.7 Connect External Expansion Boxes . ................... 2–11

2.4 Starting the System ................................... 2–11

2.5 Loading a Compact Disc................................ 2–12

2.6 Unoading a Compact Disc . . . ........................... 2–16

2.7 Connecting the System to a Network . . . ................... 2–17

2.8 Turning Off the System ................................ 2–18

2.9 Bootstrapping the System . . . ........................... 2–18

2.9.1 Bootstrapping the System Automatically Without a

Console ......................................... 2–18

2.9.2 Starting the System with a Console, Only If Necessary . . . . . 2–18

2.9.3 Recovering from Bootstrap Failures . ................... 2–19

iii

3 Expanding Your System

3.1 Guidelines for Connecting Expansion Boxes ................ 3–1

3.2 Preparing Your System for an Expansion Box ............... 3–2

3.3 Unpacking an Expansion Box . . . ........................ 3–3

3.4 Connecting One Expansion Box . . ........................ 3–3

3.5 Connecting Two Expansion Boxes ........................ 3–5

3.6 RRD42 Compact Disc Expansion Box...................... 3–6

3.6.1 Verifying the SCSI ID Number on the RRD42 Expansion

Box............................................. 3–7

3.6.2 Resetting the SCSI ID on the Second RRD42 Expansion

Box............................................. 3–7

3.7 Preventive Maintenance................................ 3–8

4 Connecting to a Network

4.1 Connecting to a ThinWire Ethernet Network ................ 4–1

4.1.1 Check the Network Select Button ..................... 4–1

4.1.2 Verify Your ThinWire Ethernet Network Installation....... 4–2

4.1.3 Connect Your System to ThinWire Ethernet Cable . ....... 4–3

4.2 Creating a ThinWire Ethernet Work Group . ................ 4–4

4.2.1 Connecting Your System to a DECconnect Faceplate ....... 4–5

4.2.2 Troubleshooting the ThinWire Segment . ................ 4–6

4.3 Connecting to a Standard Ethernet Network ................ 4–9

4.3.1 Check the Network Select Button ..................... 4–9

4.3.2 Verify Your Standard Ethernet Network Installation ....... 4–9

4.3.3 Connect a Transceiver Cable to Your System ............. 4–10

4.3.4 Troubleshooting the Standard Ethernet Connection. ....... 4–10

5 Solving Problems

5.1 Checking Cable Connections ............................ 5–1

5.2 Using the Troubleshooting Table . ........................ 5–2

5.3 Interpreting Power-Up Error Messages .................... 5–5

5.4 Running Self-Tests .................................... 5–7

5.5 Displaying System Conﬁguration Information ............... 5–8

5.6 Displaying Device Information . . . ........................ 5–9

5.7 Using the System Exerciser ............................. 5–10

5.8 Running Test Utilities for Expansion Boxes . ................ 5–12

5.9 Restarting the System after Running Tests . ................ 5–12

5.10 Reestablishing Console Parameters ....................... 5–12

5.11 Service Information . . . ................................ 5–13

5.12 Command Summary . . ................................ 5–13

A SCSI ID Numbers

A.1 SCSI ID Default Settings ............................... A–1

A.2 Determining SCSI ID Numbers .......................... A–2

A.3 Setting RRD42 ID Numbers. . ........................... A–3

B System Speciﬁcations

Glossary

Index

Figures

1–1 InfoServer 150 System Enclosure. . . ................... 1–1

1–2 Front Panel of Embedded RRD42 Drive ................. 1–2

2–1 InfoServer 150 System Components . ................... 2–3

2–2 Ports and Connectors ............................... 2–4

2–3 Rear Panel with SCSI Terminators Installed . . . .......... 2–5

2–4 Connector Covers .................................. 2–6

2–5 Attaching T-connectors . . . ........................... 2–7

2–6 Connecting the Power Cord .......................... 2–9

2–7 Connecting the Console Terminal Cable ................. 2–10

2–8 Opening the Caddy ................................ 2–13

2–9 Loading the Disc .................................. 2–14

2–10 Loading the Caddy in the Drive ....................... 2–15

2–11 Ejecting the Caddy from the Drive. . ................... 2–16

2–12 Front Panel of RRD42 Drive ......................... 2–17

3–1 Removing SCSI Terminator .......................... 3–2

3–2 Connecting One RRD42 Expansion Box ................. 3–4

3–3 Connecting Two RRD42 Expansion Boxes ............... 3–6

3–4 RRD42 Real Panel ................................. 3–7

4–1 Position of Network Select Button and Ethernet Lights . . . . 4–2

4–2 Position of Halt Button . . ........................... 4–3

4–3 Attaching T-Connector with Cable Segment to BNC

Connector ........................................ 4–4

4–4 Connecting to DECconnect Faceplate................... 4–6

4–5 Disconnecting T-connector ........................... 4–8

4–6 Securing Standard Ethernet Connector . ................ 4–10

Tables

1Related Documents ................................ viii

3–1 SCSI Devices Self-Test Status Codes . . . ................ 3–8

5–1 Troubleshooting Basic System Problems ................ 5–3

5–2 Power-Up and Self-Test Display Identiﬁers .............. 5–6

5–3 Deﬁnition of Mnemonics ............................ 5–9

5–4 SET Command Summary............................ 5–13

5–5 TEST Command Summary . . ........................ 5–14

5–6 SHOW Command Summary. . ........................ 5–15

A–1 SCSI ID numbers for InfoServer 150 System ............. A–2

Preface

Document Purpose

This document describes how to install, test, operate, and maintain the

InfoServer 150 system. This system is a general-purpose disk storage server

that quickly and efﬁciently transfers data between disks connected to the

server and remote network client systems.

For information on session management and software commands, see the

InfoServer System Operations Guide.

Intended Audience

This document addresses persons responsible for installing, operating, or

maintaining the InfoServer 150 system.

Document Structure

This document is organized as follows:

• Chapter 1 provides an overview of the InfoServer 150 system.

• Chapter 2 provides instructions for installing new InfoServer 150 systems.

• Chapter 3 provides information on installing and using add-on storage

devices and software-loading devices such as compact disc drives.

• Chapter 4 explains how to connect your system to a ThinWire Ethernet

or standard Ethernet network. The chapter also explains how to connect

systems into a simple ThinWire work group.

• Chapter 5 provides troubleshooting information.

Appendixes provide information on the following topics:

• Setting SCSI ID numbers on drives for custom conﬁgurations

• System speciﬁcations

The glossary explains technical terms used in the document.

vii

Beliebte Netzwerkspeicherserver Handbücher anderer Marken

HP NetStorage 6000 Bedienungsanleitung

Synology

Synology RackStation RS816 Handbuch

D-Link

D-Link ShareCenter Pro DNS-1200-05 Bedienungsanleitung

Avid Technology

Avid Technology VideoRAID ST Sicherheitsleitfaden

Western Digital

Western Digital My Cloud Home Duo Bedienungsanleitung

PrimeArray

PrimeArray 4xxx Bedienungsanleitung

Buffalo

Buffalo TeraStation WSS WSH5010N6 Bedienungsanleitung

Planex

Planex MZK-NAS01SG Bedienungsanleitung

Intel

Intel SS4000-E - Entry Storage System NAS Server Bedienungsanleitung

Synology

Synology RS2212+ Bedienungsanleitung

Allnet

Allnet ALL69000 Bedienungsanleitung

Adaptec

Adaptec 5325301580 Bedienungsanleitung

Motorola

Motorola EXORdisk II Bedienungsanleitung

Sony

Sony XDAAI1PK Bedienungsanleitung

Cisco

Cisco Linksys NAS200 Original Betriebsanleitung

Sans Digital

Sans Digital MR4UT6G Bedienungsanleitung

AIC

AIC FB128-LX Bedienungsanleitung

Dell

Dell PowerVault NX3500 Gebrauchsanweisung