Digitus DN-82010-1 Bedienungsanleitung

10/100Base-TX to 100Base-FX

Media Converter

User’s Manual

1. Overview

IEEE802.3u Ethernet supports two types media for network connection

such as 10/100Base-TX and 100Base-FX. The bridge media converter

is designed with a switch controller and buffer memory that connects

two types segments operation smoothly. This converter can be used as

standalone unit or as slide-in module to the 483mm (19”) converter rack

Chassis for use at a central wiring closet.

2. Check List

Before you start installing the Converter, verify that the package

contains the following:

- The TP-Fiber Converter

- AC-DC Power Adapter (for external models) or Power Cord

(for internal models)

- The User’s Manual

Please notify your local sales distributor immediately if any of

the mentioned items is missing or damaged.

3. Technical Specifications

Standards IEEE802.3, IEEE802.3U, 10/100Base-TX,

100Base-FX

Media Supported

10Base-T: Cat. 3, 4, 5 UTP/STP, max 100m

100Base-TX: Cat5 UTP/STP, max 100m

Multimode fiber model: (50/125µm, 62.5/125µm)

Singlemode fiber model: (9/125µm)

TP Connector SC/ST/FC

Referenced

Transmission

Distance

Dual-fiber multimode: 2km

Dual-fiber singlemode: 20/40/60/80/l 00/120km

Single-fiber singlemode: WDM 20/40/60/80km

Data Forward Rate 10Mbps / 100Mbps

Flow Control IEEE802.3x flow control for full-duplex model

Back-pressure flow control for half-duplex mode

Power Supply 5VDC or 110~260VAC or 48VDC

Power

consumption 2.5W

Operation Temperature 0℃to 55℃

Relative Humidity 5% to 80% (non-condensation)

Feature

1. Built in 2-port switch:

-Supports modified cut-through frame forwarding for low latency

-Supports pure converter mode data forwarding for extreme low latency

-Supports flow control for full and halt duplex operation

-Bandwidth control

-Forward 1600 bytes packet for management

2. Supports 100Base-FX standard

3. Built in 128KB RAM for data buffer

4. Supports Auto MDI-MDIX function

5. Supports link fault pass through function (LFP)

6. LED display for link/activity, full/half, 10/100M

4. Installing the Converter

Standalone unit:

→Verify the AC-DC adapter conforms to your country AC power

requirement and insert the power plug

→Connect the media cable for network connection

Slide-in unit:

→The slide-in Media Converter and Converter Rack Chassis should

supplied only from the same source, both Media Converter Rack

Chassis are built to match each other at dimension, DC jack, DC

receptacle and power safety.

→Turn off the 483mm (19”) converter rack power

→Ensure that there is no activity in the network

→Locate +5V DC power jack on converter back, carefully slide in

and plug to 483mm (19”) rack +5V DC power receptacle

→Connect the media cable for network connection

→Turn on the converter rack power, the Power LED will light up

Fiber Port Attach the fiber cable, the TX, RX fiber cable must be paired at both ends.

Default: Full duplex mode

TP Port Attach TP Cat.5 cable to TP Port

Wire connection, Front and Side panel

Fig. 1 Basic Network Connection

Fig. 2 Converter Front Panel for external power

Fig. 3 Rear Panel

5. LED Description

LED indicator lamp Status Description

FX Link/Act

On Connection status display for Fiber Link.

“ON” indicates that Fiber link is in correct connection.

Blink Active status display of fiber link.

“Blink” indicates packet goes through FX end.

TX Link/Act

On Connection status display for electric link.

“ON” indicates that electric link is in correct.

Blink Active Status display of fiber link

“Blink” indicates packet goes through TX end.

FDX

On Transceiver works in the full duplex mode.

Off Transceiver works in the half duplex mode.

PWR On Power is on and normal.

SD On Fiber signal is detected.

100M

On Transfer rate of electric interface is 100Mbps.

Off Rate of electric interface is 10Mbps

6. Connecting to TP, Fiber Device

Converter TP Port

10/100TX

Default: 10/100Mbps Nway

a. Auto-Negotiation for Nway TP partner

b. Half-Duplex for non-Nway TP partner, Class II hub,

or 10Base-T device

Converter Fiber Port

100FX

100Mbps with duplex mode selectable:

a. Full-duplex for 100Fdx fiber link partner

b. Half-duplex for 100Hdx fiber link partner

FX duplex mode slide switch locates on the rear panel.

7. Troubleshooting

If the media converter fails, isolate and correct the failure by determining

the answers to the following questions and then taking the indicated

action:

1. Is the power LED on the media converter illuminated?

Is the power adapter the proper type of voltage and cycle frequency

for the AC outlet?

Is the power adapter properly installed in the media converter and in

the outlet?

Contact your local sales distributor for technical Support.

YES

Proceed to step 2.

2. Is the “Duplex/Link” LED illuminated on a port with twisted-pair

cable installed?

Check the copper cables for proper connection.

YES

OFF = The media converter has selected half-duplex mode.

ON = The media converter has selected full-duplex mode.

If the mode is not correct, disconnect and reconnect the twisted pair

cable to restart the initialization process.

Proceed to step 3.

3. Is the ”Link action” LED illuminated on the fiber cable port?

Check the fiber cables for proper connection.

Verify that the TX and RX cables are connected to the RX and TX

ports, respectively, on the 100Base-FX device.

YES

Proceed to step 4.

4. Is the “Speed” LED illuminated on a port with twisted-pair cable

installed?

Check the copper cables for proper connection.

YES

OFF = The media converter has selected 10Mbps operation.

ON = The media converter has selected 100Mbps operation.

If the speed is not correct, disconnect and reconnect the twisted pair

cable to restart the initialization process.

Note: Connecting to Router, Bridge or Switch, please refer to the

device’s Technical Manual.

Hereby ASSMANN Electronic GmbH, declares that this device is in compliance with the

requirements of Directive 2014/30/EU (EMC), Directive 2014/35/EU (LVD) and the Directive

2011/65/EU for RoHS compliance. The complete declaration of conformity can be requested

by post under the below mentioned manufacturer address.

Warning:

This device is a class B product. This equipment may cause some radio interference in living

environment. In this case, the user can be requested to undertake appropriate measures to

prevent interference.

www.assmann.com

Assmann Electronic GmbH

Auf dem Schüffel 3

58513 Lüdenscheid

Germany

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Digitus Medienkonverter Handbücher

Digitus

Digitus DN-95208 Bedienungsanleitung

Digitus

Digitus DS-55303 Bedienungsanleitung

Digitus

Digitus DS-40310-1 Bedienungsanleitung

Digitus

Digitus DS-40137 Bedienungsanleitung

Digitus

Digitus DC-40100 Bedienungsanleitung

Digitus

Digitus DS-40131 Bedienungsanleitung

Digitus

Digitus DN-82212 Bedienungsanleitung

Digitus

Digitus DA-70460 Bedienungsanleitung

Digitus

Digitus DS-40201 Bedienungsanleitung

Digitus

Digitus DS-33150 Bedienungsanleitung

Digitus

Digitus DS-40138 Bedienungsanleitung

Digitus

Digitus DA-70464 Bedienungsanleitung

Digitus

Digitus DN-651140 Bedienungsanleitung

Digitus

Digitus DA-70473 Bedienungsanleitung

Digitus

Digitus DS-42140 Bedienungsanleitung

Digitus

Digitus DS-45324 Bedienungsanleitung

Digitus

Digitus DS-43305 Bedienungsanleitung

Digitus

Digitus DA-70460 Bedienungsanleitung

Digitus

Digitus DS-45322 Bedienungsanleitung

Digitus

Digitus DC-33151 Bedienungsanleitung

Digitus

Digitus DA-70156 Bedienungsanleitung

Digitus

Digitus DS-55515 Bedienungsanleitung

Digitus

Digitus DA-70465 Bedienungsanleitung

Digitus

Digitus DA-70471 Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung