Digitus DS-55303 Bedienungsanleitung

HDMI EXTENDER SPLITTER SET, 1X4

Manual

DS-55303

The Digitus HDMI Extender Splitter Set, 1x4 offers an extender and

splitter solution of up to 40 m for the highest demands. It is used to

transmit digital video and audio signals to a maximum length of up to

40 m and to distribute them to up to four monitors/screens. The highest

supported video resolution is 1080p / 60Hz. The transmitter unit

features an EDID switch, which can be used to regulate resolution and

audio format of the output signal. The transmitter also has an HDMI

Loop Out Port, which allows you to connect a local monitor. Thanks to

PoC (Power over Cable) support, it is only the transmitter unit that needs

to be powered. The package includes four infrared units (1x transmitter,

4x receivers), which can be used for the remote control of the connected

input source.

Important Safety Instructions

1. Do not mix up the Transmitter and Receiver, and the IR blaster and

IR receiver.

2. Do not plug-in/out the cables, when it is in using.

3. Use DC 5V power supply only. Make sure the specification matched

if using 3rd party DC adapters.

4. Support power from transmitter to receiver unit over the CAT6 cable.

Package Contents

Transmitter unit ×1pcs Receiver unit ×4pcs DC5V/3A ×1pcs

User Manual ×1pcs IR blaster extension

cable x1pcs

IR receiver extension

cable ×4pcs

Features

1. Distribute 1 HDMI source to 4 HDMI displays over network cable

simultaneously.

2. Support one HDMI Loop-out.

3. Compatible with CAT6/6a/7 network cables.

4. The transmission distance is up to 40m/131ft.

5. The highest resolution supported is 1920x1080@60Hz.

6. Support 20~60KHz IR pass back.

7. Support EDID setting function.

8. Support power from transmitter to receiver unit over the CAT6 cable.

9. Plug and Play.

10. Wall-mounted function, easy installation.

Specification

Part No. DS-55303

Technical

Input HDMI×1 (Type A, 19 pin, female)

Output RJ45×4

Transmission distance 40 meters via CAT6

Video support

480i@60Hz, 480p@60Hz, 576i@50Hz,

576p@50Hz, 720p@50/60Hz,

1080i@50/60Hz, 1080p@50/60Hz

Audio format PCM DTS AC3

TMDS signal 0.5~1.5Vp-p (TMDS)

DDC signal 5Vp-p (TTL)

IR pass-back function Support

IR frequency Range (KHz) Support 20~60KHz IR frequency devices

HDCP HDCP1.4

Mechanical

Housing Metal enclosure

Dimensions (L×W×H mm) TX: 190(L) x 95.9(W) x 23.9(H) mm

RX: 71.6×66.6×22.6mm

Weight TX: 0.48kg RX: 0.08kg x 4pcs

Fixedness wall-mounting case with screws

Power supply 5V/3A

Power consumption <15W

Operation temperature 0~60°

Storage temperature -20~70°

Relative humidity 20-90% (no condensation)

Installation Requirements

1. HDMI source device (computer graphics card, DVD, PS3, HD

monitoring equipment etc).

2. HDMI display device like SDTV, HDTV, and projector with HDMI port.

3. UTP/STP CAT6/6A/7 cable, follow standard IEEE-568B.

Panel Description

1. Transmitter unit (TX)

①Power input (DC5V)

②EDID dip switch

③IR signal output to connect with blaster extension cable

④HDMI input

⑤HDMI output

⑥RJ45 signal output

⑦Power/signal indicator

⑧Reset button

Receiver unit (RX)

①LENGTH: for adjusting to the length of network cable

②RJ45 signal input

③RJ45 indicator led it lights on all the time with HDMI signal

transmission, flashes with no signal transmission

④DC5V power input (OPTIONAL)

⑤HDMI signal output

⑥IR signal input to connect with IR receiver extension cable

Remarks: The LENGTH key is designed for switching between automatic

and manual setting to adjust cable length. Powered on without any

operation, extender works with parameter set and memorized before.

Powered on and then press LENGTH key, the first two press, it will enter

automatic mode to adapt cable length. The following 12 times of

pressing, it will enter manual mode in 12 levels to meet different cable

length. After all 12 levels of press, it will entering auto mode again and

into next loop.

Installation Procedures

1. How to make a CAT5/5E/6 network cable

Follow the standard of IEEE-568B:

1- Orange/white 2- Orange

3- Green/white 4- Blue

5- Blue/white 6- Green

7- Brown/white 8- Bro

2. Connection

Remarks: Please do not remote control two or RX units' IR cable at the

same time, which to avoid interference.

3. Connection instruction:

1) Connect the HDMI signal source device to the Transmitter HDMI

input port with HDMI cable.

2) Connect IR blaster to EXTENDER IR OUT

3) Connect the Transmitter RJ45 port to HDMI EXTENDER RX's Rj45

input port by network cable.

HDMI input

HDMI extender splitter

power

HDMI Out

Cable

Receiver

DVD

4) Connect HDMI EXTENDER RX's HDMI output port to HDMI

display's HDMI input port by HDMI cable and set the HDMI

display's signal source to be HDMI port.

5) Supply the power (Power's signal light is red, when there are

signal input then the power light is blue), the product will work.

4. EDID Setting

1) HDMI source device reads the EDID information of the transmitter

(TX) and then output the relative HDMI signal format.

2) There are 8 build-in EDID status, and others could be selected by the

EDID switch in the HDMI extender splitter (transmitter), the detail

Setting Information shown as below:

Switch UP: Use the Arabic numeral “1” to represent

Switch DOWN: Use the Arabic numeral “0” to represent

Switch

Status

SW1 SW2 SW3 EDID Mode

0 0 0 720P@50Hz 2.1CH

1 0 0 720P@50Hz 7.1CH

0 1 0 1080i@60Hz 2.1CH

1 1 0 1080i@60Hz 7.1CH

0 0 1 1080P@60 2.1CH

1 0 1 1080p@60Hz 7.1CH

0 1 1

Read Loop-out (if not connect

the loop-out show default)

1 1 1 Default 720P@50Hz 2.1CH

FAQ

Q: No image or audio output on display?

1) Please check whether display on standby mode;

2) Please check whether display HDMI signal channel in accord

with HDMI input port

3) Please check whether “LINK” LED on RX side keeps on, LED flash

means RX does not receive signal from TX.

4) Please check whether signal indicator LED on TX turns blue, LED

on red means no input signal

5) Please check whether input resolution is supported by this

product.

Q: Image unstable?

A: 1. Press the “LENGTH” or “RESET” button on the transmitter to

re-identify the signal;

2. Please pull & plug CAT cable on corresponding port to

reconnect.

Q: Only partial ports have output?

1. Please check whether CAT cable or HDMI cable connected

correctly

2. Press the “LENGTH” or “RESET” button on the transmitter to

re-identify the signal;

3. Please pull & plug CAT cable on corresponding port to

reconnect.

Disclaimer

The product name and brand name may be registered trademark of related

manufacturers.TM and ® may be omitted on the user manual. The pictures on the

user manual are just for reference, and there may be some slight difference with the

real products.

We reserve the rights to make changes without further notice to a product or system

described herein to improve reliability, function or design.

Hereby Assmann Electronic GmbH, declares that the Declaration of Conformity is

part of the shipping content. If the Declaration of Conformity is missing, you can

request it by post under the below mentioned manufacturer address.

www.assmann.com

Assmann Electronic GmbH

Auf dem Schüffel 3

58513 Lüdenscheid

Germany

Inhaltsverzeichnis

Andere Digitus Medienkonverter Handbücher

Digitus

Digitus DS-45340 Bedienungsanleitung

Digitus

Digitus DN-82110-1 Bedienungsanleitung

Digitus

Digitus DC-33151 Bedienungsanleitung

Digitus

Digitus DC-40100 Bedienungsanleitung

Digitus

Digitus DN-95204 Bedienungsanleitung

Digitus

Digitus DA-70848 Bedienungsanleitung

Digitus

Digitus DS-43200 Bedienungsanleitung

Digitus

Digitus DA-70460 Bedienungsanleitung

Digitus

Digitus DisplayPort DA-70472 Bedienungsanleitung

Digitus

Digitus DS-40130 Bedienungsanleitung

Digitus

Digitus DA-70157 Bedienungsanleitung

Digitus

Digitus DA-70820 Bedienungsanleitung

Digitus

Digitus DA-70159 Bedienungsanleitung

Digitus

Digitus DC-KVS-12 Bedienungsanleitung

Digitus

Digitus DS-41200 Bedienungsanleitung

Digitus

Digitus DA-70465 Bedienungsanleitung

Digitus

Digitus DN-652101-1 Bedienungsanleitung

Digitus

Digitus DN-82020-1 Bedienungsanleitung

Digitus

Digitus DS-45322 Bedienungsanleitung

Digitus

Digitus DA-70464 Bedienungsanleitung

Digitus

Digitus DA-70158 Bedienungsanleitung

Digitus

Digitus DN-82030 Bedienungsanleitung

Digitus

Digitus DS-40101 Bedienungsanleitung

Digitus

Digitus DS-40137 Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung