Digitus DN-16054 Bedienungsanleitung

OUTDOOR IR

NETWORK CAMERA Series

INSTALLATION GUIDE

Please read instructions thoroughly before operation and retain it for future reference.

1. OVERVIEW

1.1 Package Content

□Network camera □Installation Sticker

□Installation Guide □RJ45 cable extender adapter

□Ground Wire

□CD-ROM disc (including user manuals & CMS software “Video Viewer”)

1.2 Dimensions

246.87

282.4

236.03

212.63

117.89

1.2 Cable Overview

CABLE DESCRIPTION

RJ45 network cable Connect it to the supplied RJ45 cable extender adapter for cable extension, and

prepare another RJ45 network cable with suitable length for your connection.

Reset wires Remove the insulating coating of these two wires, and twist them together to reset

default. This will reset all parameters, including the IP address to factory default settings.

Note: Disconnect power before twisting these two wires together, and connect to power

again for reset default. When the reset is done, disconnect these two wires.

Power wires Connect to AC power supply. For details, please refer to “2.2 Connect to power” at page

2. INSTALLATION & CONNECTION

2.1 Install the Camera

Note: The illustration below is for installation only, and the actual product may look

different from the illustration below.

2.2 Connect to power

Get a power cord and cut off its female connector side. Then, remove the insulating coating

to reveal positive, negative and ground wires.

Find the two wires labeled “AC+” (red) & “AC-” (black) on your camera, and remove a small

piece of their insulating coating to reveal the naked wires.

Twist the camera’s and power cord’s wires together according to the corresponding

electrodes (positive to positive, negative to negative, disregarding the ground wire). Then,

use the insulation tape to cover the connected wires.

3. ETHERNET CONNECTION

Before using this network camera, please follow the instructions below to finish the

network connection settings based on your installation environment:

To configure the network settings, you must connect the camera to your PC by LAN.

For details, please refer to “3.1 Network Connection via LAN” at page 5.

To configure the network settings via Wizard, please refer to “3.2 Network

Configurations via Wizard” at page 9.

To configure the network settings via our supplied CMS software, Video Viewer,

please refer to “3.3 Network Configurations via Video Viewer” at page 13.

3.1 Network Connection via LAN

Step1:Connect this network camera and your PC via a RJ45 network cable, and make

sure the camera is powered on.

Step2:Set the PC’s IP address as “192.168.1.XXX” (1~255, except 10).

For Windows 2000 users:

a) Select “Start” “Settings” “Network and Dial-up Connections”.

b) Right-click on “Local Area Connection”, and select “Properties”.

c) In the “General” tab, select “Internet Protocol (TCP/IP)”, and select “Properties”.

d) In the “General” tab, select “Use the following IP address”, and set the IP address as

described below.

Note: It’s recommended to note down the current settings first and then change

as instructed. It’s helpful when you need to restore the PC network settings

for connecting to Internet later.

e) Click “OK” to close the “Internet Protocol (TCP/IP) Properties” dialog box. Then, click “Close”

to close the “Local Area Connection Properties” dialog box.

For Windows XP users:

a) Select “start” “All Programs” “Control Panel” “Network and Internet Connections” 

“Network Connections” (If you’re in “Category View”).

b) In “LAN or High-Speed Internet”, right-click on “Local Area Connection”, and select

“Properties”.

c) In the “General” tab, select “Internet Protocol (TCP/IP)”, and select “Properties”.

d) In the “General” tab, select “Use the following IP address”, and set the IP address to

“192.168.1.XXX” (XXX can be any value from 1~255 except 10).

Note: It’s recommended to note down the current settings first and then change

as instructed. It’s helpful when you need to restore the PC network settings

for connecting to Internet later.

e) Click “OK” to close the “Internet Protocol (TCP/IP) Properties” dialog box. Then, click “Close”

to close the “Local Area Connection Properties” dialog box.

For Windows Vista users:

a) Select “ ” (start) “Control Panel” “Network and Internet” to enter the “Network and

Sharing Center”. Then, click “Manage network connections” (If you’re in “Category View”).

b) Right-click on “Local Area Connection”, and select “Properties”.

c) In the “General” tab, select “Internet Protocol Version 4 (TCP/IPv4)”, and select “Properties”.

d) In the “General” tab, select “Use the following IP address”, and set the IP address as

described below.

Note: It’s recommended to note down the current settings first and then change

as instructed. It’s helpful when you need to restore the PC network settings

for connecting to Internet later.

e) Click “OK” to close the “Internet Protocol Version 4 (TCP/IPv4) Properties” dialog box. Then,

click “Close” to close the “Local Area Connection Properties” dialog box.

3.2 Network Configurations via Wizard

A quick installation wizard is available via your web browser for password change, date &

time settings, and network configurations.

For details about the wizard, please refer to “3.2.1 Setting in Wizard” at page 9.

For details about DDNS setting for PPPoE and DHCP, please refer to “3.2.2 DDNS

Setting” at page 11.

Note: You can also change the settings in the system configuration page via your

web browser later. For details, please refer to “5. ACCESSING THE CAMERA

VIA WEB BROWSER” in the user manual.

3.2.1 Setting in Wizard

Step1:Open your web browser, for example, Microsoft Internet Explorer, and enter

“http://192.168.1.10” in the URL address box.

Step2:In the login page, key in the default user name (admin) and password (admin),

and enter the security code from the image below. Then, click “LOGIN”.

Step3:The wizard is then starting analyzing your network environment, and shows your

network environment. Select “Next” to continue.

Step4:In “Account”, change the access password if needed.

If not, leave all the columns blank, and select “Next”.

Inhaltsverzeichnis

Andere Digitus Sicherheitskamera Handbücher

Digitus

Digitus HD NETWORK SURVEILLANCE CAMERA Bedienungsanleitung

Digitus

Digitus DN-16084 Bedienungsanleitung

Digitus

Digitus IP Network Camera None Bedienungsanleitung

Digitus

Digitus DN-6032 Bedienungsanleitung

Digitus

Digitus DN-16065-1 Bedienungsanleitung

Digitus

Digitus network bullet camera Bedienungsanleitung

Digitus

Digitus DN-16026 Bedienungsanleitung

Digitus

Digitus Plug&View DN-16038 Bedienungsanleitung

Digitus

Digitus NETWORK CAMERA Bedienungsanleitung

Digitus

Digitus DN-16050 Bedienungsanleitung

Digitus

Digitus DN-16062 Bedienungsanleitung

Digitus

Digitus DN-18600 Bedienungsanleitung

Digitus

Digitus DN-16069 Bedienungsanleitung

Digitus

Digitus DN-16059-1 Bedienungsanleitung

Digitus

Digitus DN 16058 Bedienungsanleitung

Digitus

Digitus DN-16085 Bedienungsanleitung

Digitus

Digitus DN-16027 Bedienungsanleitung

Digitus

Digitus DN-16059 Bedienungsanleitung

Digitus

Digitus DN-16026 Bedienungsanleitung

Digitus

Digitus DN-16083 Bedienungsanleitung

Digitus

Digitus DN-16050 Bedienungsanleitung

Digitus

Digitus Plug&View OptiView DN-16028 Bedienungsanleitung

Digitus

Digitus DN-16027 Bedienungsanleitung

Digitus

Digitus DN-18604 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung

Lumens

Lumens VC-A50PNW Bedienungsanleitung