Digitus DN-16069 Bedienungsanleitung

ADVANCED HD NETWORK

FIXED DOME CAMERA

INSTALLATION GUIDE

Please read instructions thoroughly before operation and retain it for future reference.

IMPORTANT SAFEGUARD

All lead-free products offered by the company comply with the requirements of the

European law on the Restriction of Hazardous Substances (RoHS) directive, which means

our manufacture processes and products are strictly “lead-free” and without the hazardous

substances cited in the directive.

The crossed-out wheeled bin mark symbolizes that within the European Union the product

must be collected separately at the product end-of-life. This applies to your product and

any peripherals marked with this symbol. Do not dispose of these products as unsorted

municipal waste. Contact your local dealer for procedures for recycling this equipment.

This is a class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

Federal Communications Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to correct the interference at

his own expense.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device mat not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired

operation.

Trademark Acknowledgements

iPad

& iPhone

are the registered trademarks of Apple Inc.

Android™ is a trademark of Google Inc. Use of this trademark is subject to Google Permissions.

Microsoft

, Windows

& Internet Explorer

are registered trademarks of Microsoft Corporation in the United

States and/or other countries.

Disclaimer

We reserve the right to revise or remove any content in this manual at any time. We do not warrant or assume

any legal liability or responsibility for the accuracy, completeness, or usefulness of this manual. The content of

this manual is subject to change without notice.

This product doesn’t have a standby / shutdown mode.

MPEG4 Licensing

THIS PRODUCT IS LICENSED UNDER THE MPEG4 VISUAL PATENT PORTFOLIO LICENSE FOR THE

PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER FOR (i) ENCODING VIDEO IN

COMPLIANCE WITH THE MPEG4 VISUAL STANDARD (“MPEG-4 VIDEO”) AND/OR (ii) DECODING

MPEG4 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND

NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED BY

MPEG LA TO PROVIDE MPEG4 VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY

OTHER USE. ADDITIONAL INFORMATION INCLUDING THAT RELATING TO PROMOTIONAL INTERNAL

AND COMMERCIAL USES AND LICENSING MAY BE OBTAINED FROM MPEG LA, LLC. SEE

HTTP://WWW.MPEGLA.COM.

GPL Licensing

This product contains codes which are developed by Third-Party-Companies and which

are subject to the GNU General Public License (“GPL”) or the GNU Lesser Public

License (“LGPL”).

The GPL Code used in this product is released without warranty and is subject to the

Further source codes which are subject to the GPL-licenses are available upon request.

We are pleased to provide our modifications to the Linux Kernel, as well as a few new

commands, and some tools to get you into the code. The codes are provided on the FTP

site, and please download them from the following site or you can refer to your distributor:

TABLE OF CONTENTS

1. CAMERA NETWORK CONFIGURATIONS ........................................................................................ 1

1.1 Camera Overview ..................................................................................................................................... 1

1.2 Assemble & Install Camera ....................................................................................................................... 1

1.3 Understand How Your Laptop / Computer Connect to Internet ................................................................. 2

1.4 Wireless Router + Modem......................................................................................................................... 2

1.4.1 Configure on Laptop / PC.................................................................................................................................2

1.4.2 Configure on iPhone / iPad ..............................................................................................................................4

1.5 Router + Modem ....................................................................................................................................... 6

1.6 Modem / Hub + Modem............................................................................................................................. 9

1.7 Change Default Account ......................................................................................................................... 12

1.7.1 From Web Browser ........................................................................................................................................12

1.7.2 From iPhone / iPad ........................................................................................................................................12

2. BEFORE YOU START TO USE ........................................................................................................ 13

APPENDIX 1 CHANGE IP ADDRESS OF YOUR LAPTOP / PC .......................................................... 14

APPENDIX 2 MOBILE SURVEILLANCE VIA EAGLEEYES ................................................................. 17

A2.1 Prerequisites......................................................................................................................................... 17

A2.2 Where to download............................................................................................................................... 17

APPENDIX 3 POE CONNECTION ....................................................................................................... 18

APPENDIX 4 CONFIGURE PORT FORWARDING.............................................................................. 19

APPENDIX 5 Q&A ................................................................................................................................ 20

1. CAMERA NETWORK CONFIGURATIONS

Please follow the instructions below to finish camera installation and network configurations.

You may configure the network connection of this network camera with your laptop / computer, or with your iPhone

or iPad

based on your network environment.

1.1 Camera Overview

1.2 Assemble & Install Camera

Step1: Loosen the three screws on the camera to remove the dome cover.

Step2: Make sure the screw holes on the plate are aligned with the holes on the camera base.

Note: If not, slightly loosen the two screws on the plate and rotate it.

Step3: Mark the locations of the two screw holes on the ceiling, and drill a hole for each on the ceiling.

Note: The distance between your camera and the location you want to monitor should be 3 ~ 4 meters.

Step4: Fix the camera to the ceiling with the supplied screws.

Step5: Adjust the position and viewing angle of the camera, and fasten the two screws on the plate to fix.

Note: Do not tilt the camera lens too up or down. Part of the IR LEDs might be covered or the dome

cover might not be able to be replaced back.

Step6: Replace the dome cover back to the camera.

Note: Before replacing the cover, make sure the cover is clean and so the camera view is clear.

Step7: Connect your camera to power.

Note: This camera also supports POE connection. For connection details, please refer to “APPENDIX 3

POE CONNECTION” at page 18.

1.3 Understand How Your Laptop / Computer Connect to Internet

Then, connect your network camera directly to your wireless router / router / hub / modem with a network cable,

and power it on.

Note: Check (LAN) status indicator is always on, not blinking. If it’s blinking, check your RJ45

network cable and ensure it’s not disconnected or defect.

If you’re using:

Wireless router + modem, please refer to “1.4 Wireless Router + Modem”.

Router + modem, please refer to “1.5 Router + Modem”.

Modem or modem + hub, please refer to “1.6 Modem / Hub + Modem”.

For your account safety, it’s recommended to change the default account setting. For details, please refer to “1.7

Change Default Account” at page 12.

1.4 Wireless Router + Modem

You may use your laptop / PC, or your iPhone / iPad to complete the network configuration of the camera.

1.4.1 Configure on Laptop / PC

Before configuring this camera on your laptop / PC, make sure:

Your Windows operating system is Windows 7, Vista or XP.

(Recommended) Your wireless router supports UPnP, and this function is enabled.

Note: If your wireless router doesn’t support UPnP, you need to additionally access your router for port

forwarding. For details, please refer to “APPENDIX 4 CONFIGURE PORT FORWARDING” at page

19.

You have noted down the IP address of your router, and the assigned IP address(es) and port(s) of other

devices connected to the same router.

Note: For details, please refer to the user manual of your wireless router, or check with your installer.

You have downloaded “IPScan.exe” in your laptop / PC.

Note: Please download “IPScan.exe” from www.surveillance-download.com/user/m328a.swf.

Step1: Connect your laptop / PC to the wireless network with the camera connected.

Step2: Open “IPScan.exe” ( ) to search your camera. The default IP address of the camera is 192.168.1.10.

If you connect two or more cameras to the wireless router, “IPScan” will list many cameras with different

IP addresses after searching. To know which camera you’re configuring, you may identify each with its

unique MAC address.

Note: The MAC address can be found on the sticker at the bottom side of the camera.

Step3: Select the IP address you want to configure, and click “Configure” to show the IP setting page, and

change the IP address, gateway and port number.

For example, the IP address of your router is 192.168.2.1. Then in this step, you need to change the IP

address to 192.168.2.xx (“xx” means any value from 2 ~ 50), and change the gateway to “192.168.2.1

(the same as the IP address of your router). Then, change the port number to any value other than 88 if

needed.

Note: Make sure the IP address you change is not used by other devices connected to the same router.

Step4: Enter the user name and password of this camera to confirm the change, and exit “IPScan”. The default

user name and password are both “admin”.

Step5: Open the web browser, such as Internet Explorer, on your laptop / PC, and enter the IP address you just

set on the URL column to access this camera. The format is “http://ipaddress:portnum”.

In the login page, enter the user name, password, and security code to access.

Note: Please skip the wizard.

Step6: Go to “Config.” “DDNS”, and enable the DDNS service.

If your router supports UPnP, please proceed Step7.

If your router doesn’t support UPnP, note down the host name, such as MAC000E5320E73E.ddns.eagleeyes.tw,

and click “Save”. Then, access your wireless router for port forwarding as instructed in “APPENDIX 4 CONFIGURE PORT

FORWARDING” at page 19.

Step7: Go to “UPnP”, and enable the UPnP service.

Then, enable “Port Mapping”, and click “Save” to start port mapping automatically.

When the configurations are saved successfully, you’ll see a message indicating the IP address and port

number assigned to your camera.

Note down the IP address and port number, and log out the camera.

Check your connection

Step1: Connect your laptop / PC to Internet with the wireless network other than the one camera is connected.

Step2: Enter the IP address or host name you just noted down and the port number in the URL address box of

the web browser, and see if you can enter the login page of the camera successfully.

The format is “http://ipaddress:portnum” or “http://hostname:portnum”.

1.4.2 Configure on iPhone / iPad

Before configuring this camera on iPhone / iPad, make sure:

You have installed our mobile program, EagleEyes-Lite or EagleEyes-Plus, on your iPhone or iPad. For

details, please refer to “APPENDIX 2 MOBILE SURVEILLANCE VIA EAGLEEYES” at page 17.

Note: EagleEyes HD for iPad doesn’t support network configuration. Please install EagleEyes-Lite or

EagleEyes-Plus on your iPad instead.

(Recommended) Your wireless router supports UPnP, and this function is enabled.

Note: If your wireless router doesn’t support UPnP, you need to additionally access your router for port

forwarding. For details, please refer to “APPENDIX 4 CONFIGURE PORT FORWARDING” at page

19.

Your camera is connected to your wireless router with a RJ45 network cable, and it’s powered on.

Note: Check (LAN) status indicator is always on, not blinking. If it’s blinking, check your RJ45

network cable and ensure it’s not disconnected or defect.

You have checked the IP address used by your wireless router with the camera connected as instructed

below, and written it down. You’ll need it later.

Connect your iPhone / iPad to the wireless router with cameras connected, and go to “Settings” “Wi-Fi”.

Select “>” near the selected wireless network to enter the details.

The IP address shown in “Router” is the IP address used by your wireless router. In the following example,

the IP address of your router is 192.168.2.1.

Note: This address will be needed when you want to access your router for port forwarding later.

Step1: Connect your iPhone to the wireless router which has the camera connected.

Step2: Open “EagleEyes” on your iPhone or iPad.

In the address book, click “+” to add new device. Then, select “Local Network Search” to search your

network camera. You’ll see an IP address assigned by your router.

Note: If you can’t find the camera, make sure your LAN status indicator ( ) is always on, and search

again after 3 minutes.

If you connect two or more cameras to the wireless router, you’ll see many cameras with different IP

addresses after searching. To know which camera you’re configuring, you may identify each with its

unique MAC address.

Note: The MAC address can be found on the sticker at the bottom side of the camera.

Step3: Select the IP address you want to configure

to show the IP address setting page.

The default port number is 88. You may

change it to any value (such as 8080) if

the port number of 88 is blocked.

Step4: Select “Apply” to confirm all your changes.

Then, wait till you see “Done” or “Fail” in

“Status”.

Regardless which message you see,

proceed as instructed below:

For Done, you’ll return to the new

device page.

For Fail, select “ ” on the top right side.

You’ll later be prompted to select “DDNS”

or “Local IP”. Select “DDNS” and return to

the new device page.

Step5: In the new device page, give a meaningful

name for this connection in “Title”, and click

“Save”.

Please continue with configuring port

forwarding as instructed in “APPENDIX 4

CONFIGURE PORT FORWARDING” at

page 19.

Check your connection

Step1: Switch the network mode to 3G mode on iPhone or iPad.

Step2: Start EagleEyes, and select the connection you just added to see if you can access the camera

successfully.

If yes, your network setup is successfully.

If no, go to Step3.

Step3: Switch your network mode to wireless mode on iPhone or iPad.

Step4: Start EagleEyes, and add a new connection with the IP address (e.g. 192.168.2.25) and the port number

(e.g. 88). Then, try this connection and see if you can access the camera successfully.

If yes, go for port forwarding setting as instructed in “APPENDIX 4 CONFIGURE PORT FORWARDING” at page 19.

If no, return to Step1 in “1.2.2 Configuring on iPhone / iPad” and re-configure the network again.

1.5 Router + Modem

You may use your laptop / PC to complete the network configuration of the camera.

Inhaltsverzeichnis

Andere Digitus Sicherheitskamera Handbücher

Digitus

Digitus DN-16050 Bedienungsanleitung

Digitus

Digitus DN-16027 Bedienungsanleitung

Digitus

Digitus Plug&View OptiView DN-16028 Bedienungsanleitung

Digitus

Digitus DN-18603 Bedienungsanleitung

Digitus

Digitus DN 16058 Bedienungsanleitung

Digitus

Digitus DN-16054 Bedienungsanleitung

Digitus

Digitus DN-16027 Bedienungsanleitung

Digitus

Digitus ADVANCED HD NETWORKFIXED DOME CAMER Bedienungsanleitung

Digitus

Digitus DN-16050 Bedienungsanleitung

Digitus

Digitus DN-16027 Bedienungsanleitung

Digitus

Digitus NETWORK CAMERA Bedienungsanleitung

Digitus

Digitus ADVANCED NETWORK SURVEILLANCE CAMERA Bedienungsanleitung

Digitus

Digitus HD NETWORK SURVEILLANCE CAMERA Bedienungsanleitung

Digitus

Digitus Plug&View DN-16038 Bedienungsanleitung

Digitus

Digitus DN-16036 Kurzanleitung

Digitus

Digitus DN-16059-1 Bedienungsanleitung

Digitus

Digitus DN-16084 Bedienungsanleitung

Digitus

Digitus DN-16062 Bedienungsanleitung

Digitus

Digitus DN-16026 Bedienungsanleitung

Digitus

Digitus DN-16083 Bedienungsanleitung

Digitus

Digitus network bullet camera Bedienungsanleitung

Digitus

Digitus DN-18600 Bedienungsanleitung

Digitus

Digitus IP Network Camera None Bedienungsanleitung

Digitus

Digitus DN-16052 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung