Dimplex DWF120330B Bedienungsanleitung

Owner’s Manual

Model

DWF120330B

7213550100R04

IMPORTANT SAFETY INFORMATION: Always read this manual rst

before attempting to install or use this replace. For your safety, always

comply with all warnings and safety instructions contained in this manual

to prevent personal injury or property damage.

To view the full line of Dimplex products, please visit

www.dimplex.com

2 www.dimplex.com

Table of Contents

Always use a qualied technician

or service agency to repair

this replace.

!NOTE: Procedures and

techniques that are considered

important enough to

emphasize.

CAUTION: Procedures and

techniques which, if not

carefully followed, will result in

damage to the equipment.

WARNING: Procedures

and techniques which, if not

carefully followed, will expose

the user to the risk of re,

serious injury, or death.

Welcome & Congratulations .................3

IMPORTANT INSTRUCTIONS ............... 4

Quick Reference Guide .....................6

Fireplace Installation ......................7

Operation ...............................11

Maintenance ............................14

Warranty ...............................15

Replacement Parts .......................17

Welcome & Congratulations

Thank you and congratulations for choosing to purchase an electric

replace from Dimplex, the world leader in electric replaces.

Please carefully read and save these instructions.

CAUTION: Read all instructions and warnings carefully before

starting installation. Failure to follow these instructions may result in

a possible electric shock, re hazard and will void the warranty.

Please record your model and serial numbers below for future

reference: model and serial numbers can be found on the Model and

Serial Number Label of your replace.

NO NEED TO RETURN TO THE STORE

Questions with operation or assembly? Require Parts Information?

Product Under Manufacturer’s Warranty?

For Troubleshooting and Technical Support

OR Toll-Free 1-888-DIMPLEX (1-888-346-7539)

Monday to Friday 8:00 a.m. to 4:30 p.m. EST

Please have your model number and product serial

number ready. (See above)

Serial Number Label

Model Number

4 www.dimplex.com

When using electrical appliances,

basic precautions should always

be followed to reduce the risk of

fire, electric shock, and injury to

persons, including the following:

① Read all instructions before us-

ing the electric replace.

② This replace is hot when in

use. To avoid burns, do not let

bare skin touch hot surfaces.

The trim around the heater outlet

becomes hot during heater opera-

tion.

③ Extreme caution is neces-

sary when any heater is used by

or near children or invalids and

whenever the unit is left operating

and unattended.

④ Always unplug the fireplace

when not in use.

⑤ Young children should be

supervised to ensure that they do

not play with the appliance.

⑥ The appliance is not intended

for use by young children or

inrmed persons without supervi-

sion.

⑦ If the supply cord is damaged,

it must be replaced by the manu-

facturer, or its service agent, or a

qualied person in order to avoid

a hazard.

⑧ Do not operate any unit with

a damaged cord or plug, or if the

heater has malfunctioned, or if

IMPORTANT INSTRUCTIONS

the electric replace has been

dropped or damaged in any man-

ner, contact Dimplex Technical

Service at

1-888-346-7539.

⑨Do not use outdoors.

⑩ This fireplace is not intended

for use in bathrooms, laundry ar-

eas and similar indoor locations.

Never locate heater where it may

fall into a bathtub or other water

container.

⑪ High temperature, keep electri-

cal cords, drapery, and other

furnishings at least 3 feet (0.9m)

from the front of the heater and

away from the side and rear.

⑫ Do not run the cord under

carpeting. Do not cover cord with

throw rugs, runners, or the like.

Arrange cord away from traf-

c area and where it will not be

tripped over.

⑬ Do not locate the unit directly

below a xed electrical conve-

nience outlet.

⑭ To disconnect the replace,

turn the controls off, then remove

the plug from the outlet.

⑮ Do not insert or allow foreign

objects to enter any ventilation

or exhaust opening as this may

cause an electric shock or re, or

damage to the heater.

⑯ Do not block air intake or

SAVE THESE INSTRUCTIONS

exhaust in any manner. Do not

use on soft surfaces, like a bed,

where openings may become

blocked.

⑰ All electrical heaters have

hot and arcing or sparking parts

inside. Do not use in areas where

gasoline, paint, or ammable liq-

uids are used or stored or where

the unit will be exposed to am-

mable vapors.

⑱ Do not modify the electric

replace. Use it only as described

in this manual. Any other use not

recommended by the manufactur-

er may cause re, electric shock

or injury to persons.

⑲ Avoid the use of an extension

cord. Extension cords may over-

heat and cause a risk of re. This

heater is not intended for use with

an extension cord. Plug the cord

directly into an appropriate wall

receptacle.

⑳ Do not burn wood or other ma-

terials in the electric replace.

Do not strike the replace

glass.

Always use a certied electri-

cian should new circuits or outlets

be required.

Always use properly grounded,

fused and polarized outlets.

Disconnect all power supply

before performing any cleaning,

maintenance or relocation of the

unit.

When transporting or stor-

ing the unit and cord, keep in a

dry place, free from excessive

vibration and store so as to avoid

damage.

WARNING: Remote control

contains a small battery. Keep

away from children. If swallowed,

seek medical attention immedi-

ately.

WARNING: Do not install bat-

tery backwards, charge, put in re

or mix with used or other battery

types - may explode or leak caus-

ing injury.

!NOTE: Changes or modica-

tions not expressly approved by

the party responsible for compli-

ance could void user's authority to

operate the equipment.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

NO USER-SERVICABLE PARTS INSIDE

IMPORTANT INSTRUCTIONS

6 www.dimplex.com

Quick Reference Guide

Figure 1

1. Before using the fireplace

verify the circuit breakers for

the unit on?

2. If you have any technical

questions or concerns

regarding the operation of

your electric fireplace, or

require service, contact

customer service.

3. The heater may emit a slight,

harmless odor when first

used. This odor is a normal

condition caused by the initial

heating of internal heater

parts.

4. For dimensions of your

replace, refer to Figure 1.

459mm

[18.0"]

144mm

[5.7"]

1092mm

[43"]

500mm

[19.7"]

50mm

[5.9"]

914mm (36")

Site Selection

!NOTE: A 15 Amp, 120

Volt circuit is required. A

dedicated circuit is preferred

but not essential in all cases.

A dedicated circuit will be

required if, after installation,

the circuit breaker trips or the

fuse blows on a regular basis

when the heater is operating.

Additional appliances on the

same circuit may exceed the

current rating of the circuit

breaker.

WARNING: Ensure the power

cord is not installed so that

it is pinched or against a

sharp edge and ensure that

the power cord is stored or

secured to avoid tripping or

snagging to reduce the risk of

re, electric shock or injury to

persons.

Construction and electrical

outlet wiring must comply

with local building codes and

other applicable regulations to

reduce the risk of re, electric

shock and injury to persons.

Do not attempt to wire your

own new outlets or circuits. To

reduce the risk of re, electric

shock or injury to persons,

Fireplace Installation

always use a licensed

electrician.

WARNING: The supplied

mounting bracket is designed

for use with Dimplex wall

mounted replaces only.

Improper use, or use for

purposes other than intended,

may cause damage or injury.

Installation

WARNING: Failure to install

the replace as instructed

below may result in damage

to the equipment and or may

expose the user to the risk of

re, serious injury, illness or

death.

WARNING: The replace

requires the wall mounting

bracket screws to be installed

into a minimum of two wall

studs (Figure 2).

Tools Required

• #2 Phillips screwdriver

• Pencil

• Slot screwdriver

• Bubble level (supplied)

• Drill, and drill bits as required

Approximate time: 30 minutes

for installation

1. Select an appropriate location

to mount the unit on a wall,

above an electrical outlet.

8 www.dimplex.com

Fireplace Installation

Access to the electrical outlet

must be maintained. Ensure

the installation meets the

national and state/provincial

electrical codes.

!NOTE: It is recommended

that the bottom of the unit

not be mounted higher than

1020mm (40") from the

Fireplace Installation ground

to maintain an optimized

viewing angle of the ame.

CAUTION: Ensure that the

top of the unit is at least

610mm (24") from the ceiling

or any object (i.e. Electrical

receptacles) that may obstruct

or be susceptible the ow or

temperature of air out of the

unit.

CAUTION: High temperature,

keep electrical cords, drapery,

and other furnishings at least

3 feet (0.9m) from the front of

the heater and away from the

side and rear.

2. The wall-mounting bracket

must be mounted to at

least two (2) wall studs.

Studs should be accessed

through two (2) wall-bracket

holes in one of the following

combinations: A&F, B&D, or

C&E (Figure 2).

!NOTE: Wall anchors must

be installed in the appropriate

wall locations to fasten the wall

bracket through the remaining

holes (Figure 3). For example, if

you plan to secure the bracket to

studs through holes A&D, install

anchors centered on holes B and

3. Hold the wall-mounting

bracket on the wall and mark

Figure 2

Figure 3

610 mm (24")

MINIMUM

1020 mm (40")

RECOMMENDED

9. Insert the wall anchor screws

through the wall bracket and

thread into the wall anchors.

Tighten the screw (Figure 4).

10. Install the remaining screws

through the bracket and into

the wall studs as required.

!NOTE: At least two of

the mounting screws must be

installed into a wall stud.

11. Mount the unit on the wall,

so that the tabs on the wall

bracket have been inserted

into the slots on the back of

the rebox, as shown. (Figure

12. Carefully pour and evenly

distribute the supplied glass

rock media in the Media tray

of the rebox (Figure 6).

13. Hang the front glass as-

sembly on the mounts of the

the location of ONE (1) of the

mounting holes.

4. Place the bubble level onto

the top of the wall-mounting

bracket.

5. Adjust the wall-mounting

bracket so the bubble on the

level is centered between the

two black lines.

6. Mark three (3) other mounting

screw locations, on the wall,

ensuring that the wall bracket

stays level.

7. Install the supplied wall

anchors on the drywall

marked locations by placing

a #2 Phillips screwdriver into

the recess of the anchor.

8. Press the anchor into the wall

in the desired marked position

while turning the anchor

clockwise until it is ush with

the wall.

Fireplace Installation

Figure 5

Wall anchor

Screw

Wall

bracket

Figure 4

10 www.dimplex.com

Fireplace Installation

Media Tray

Front Glass

Assembly

Figure 7

Figure 6

rebox and secure the glass

onto the unit by installing the

retaining screws (Figure 7)

14. Excess electrical cord can be

inserted back into the bottom

of the unit, into the cord

storage area.

Glass Retaining

Screw

Andere Handbücher für DWF120330B

Inhaltsverzeichnis

Andere Dimplex Kamin im Innenbereich Handbücher

Dimplex

Dimplex CFP49449BW Bedienungsanleitung

Dimplex

Dimplex Revillusion OSB20C-AU Bedienungsanleitung

Dimplex

Dimplex Sierra 48 Bedienungsanleitung

Dimplex

Dimplex EMP-075-W Bedienungsanleitung

Dimplex

Dimplex TFA36E Bedienungsanleitung

Dimplex

Dimplex BOF4056 Bedienungsanleitung

Dimplex

Dimplex Optimyst DFI400LH Bedienungsanleitung

Dimplex

Dimplex BFSL33 Bedienungsanleitung

Dimplex

Dimplex COVELO Bedienungsanleitung

Dimplex

Dimplex Revillusion RBF24DLX Bedienungsanleitung

Dimplex

Dimplex Wesley Side Control Bedienungsanleitung

Dimplex

Dimplex GDS23L8-1904GB Bedienungsanleitung

Dimplex

Dimplex CAS500R Bedienungsanleitung

Dimplex

Dimplex DF2624L Bedienungsanleitung

Dimplex

Dimplex Ignite 50 Bedienungsanleitung

Dimplex

Dimplex YEO20 Bedienungsanleitung

Dimplex

Dimplex OPTIMYST CAS400L Bedienungsanleitung

Dimplex

Dimplex CAS500R Bedienungsanleitung

Dimplex

Dimplex NAVARRA NAV15P PEBBLE Betriebsanleitung

Dimplex

Dimplex Elda Fire ELD20 Bedienungsanleitung

Dimplex

Dimplex DF2608 Bedienungsanleitung

Dimplex

Dimplex RLG25 Bedienungsanleitung

Dimplex

Dimplex LVA231 Bedienungsanleitung

Dimplex

Dimplex CAMBRIDGE STANDARD Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch