Dimplex IL095 Bedienungsanleitung

IMPORTANT:

This booklet should be left with the user after

installation and demonstration.

It should be kept in a safe place, as you mayneed

to refer to it for general instructions

or future maintenance

DIMPLEX IL095

INSTANT INLINE UNVENTED

WATER HEATER

Installation and User Guide

CONTENTS

If you experience any difficulty with the installation or operation of your new

water heater, then please refer to the “What to do if things go wrong” section

in this manual before contacting us.

INTRODUCTION

THIS APPLIANCE IS NOT INTENDED FOR USE BY PERSONS (INCLUDING CHILDREN) WITH

REDUCED PHYSICAL, SENSORY OR MENTAL CAPABILITIES,

OR LACK OF EXPERIENCE AND KNOWLEDGE, UNLESS THEY HAVE BEENGIVEN SUPERVISION

OR INSTRUCTION CONCERNING USE OF THE APPLIANCE

BY A PERSON RESPONSIBLE FOR THEIR SAFETY.

CHILDREN SHOULD BE SUPERVISED TO ENSURE THAT THEY

DO NOT PLAY WITH THE APPLIANCE.

Thank you for purchasing a quality Dimplex IL095 manufactured in England.

To enjoy your new unit at its best, please take time to read this manual thoroughly to

familiarise yourself with all instructions, BEFORE beginning installation.

•Your IL095 has been designed for convenience, economy and safetyof use, provided that it is

installed, used and maintained in good working order and in accordance with our instructions and

recommendations.

•All wiring and installation must be supervised by a suitably qualified person.

•THIS APPLIANCE MUST BE EARTHED.

•The installation must be in accordance with the current edition of BS.7671 (the “IEE Wiring

Regulations”) and “Part P” of the “Building Regulations” in force at the time of installation.

Installations outside England and Wales must also conform to any local regulations in effect.

•This appliance is intended to be permanently connected to the fixed electrical wiring of the mains

supply with its own dedicated supply.

•This appliance must NOT be fitted where it may be subjected to freezing conditions

DO NOT switch the appliance on if you suspect it of being frozen.

Wait until you are sure it has thawed out.

•Isolate the mains electrical and water supply before removing the front cover of the appliance.

Section

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Important Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

How to install your IL095 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Commissioning your IL095 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

How to use your IL095 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

What to do if things go wrong (1) Self Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Dimplex After Sales Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Additional Accessories and Common Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . .

What to do if things go wrong (2) Professional Service . . . . . . . . . . . . . . . . . . . . . . .

How your IL095 Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Guarantee and Contact Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Page

IMPORTANT SAFETY INFORMATION

WARNING: ALL WIRING AND INSTALLATION MUST BE SUPERVISED BY A SUITABLY

QUALIFIED PERSON.

WARNING: DO NOT INSTALL THIS UNIT WHERE IT MAY BE SUBJECTED TO FREEZING

CONDITIONS.

BEFORE YOU START

Check that the mains electric is capable of supplying the required current.

See the rating plate forcurrent requirements.

Check the pressure of the main water supply.

To operate correctly, the unit requires the following running pressures.

Check the rating plate to see which applies:-

Dynamic Water Pressure

Basin Shower

Model

Minimum Maximum Minimum Maximum

Up to

9.5kW 10 psi (0.7 bar)

(69 kPa) 150 psi (10.3 bar)

(1035 kPa) 15 psi (1.1 bar)

(103 kPa) 150 psi (10.3 bar)

(1035 kPa)

Up to

10.8kW 15 psi (1.1 bar)

(103 kPa) 150 psi (10.3 bar)

(1035 kPa) 20 psi (1.4 bar)

(138 kPa) 150 psi (10.3 bar)

(1035 kPa)

Up to

12.0kW 20 psi (1.4 bar)

(138 kPa) 150 psi (10.3 bar)

(1035 kPa) 25 psi (1.8 bar)

(172 kPa) 150 psi (10.3 bar)

(1035 kPa)

FIXING THE UNIT TO THE WALL

Deciding the position

•If being used in a public place, position the unit out of reach to discourage vandalism.

•Fit the unit onto a flat piece of wall, well away from any potential splashes of water or spray.

•Position the unit either upright orlengthways (diagram 1), whichever is most convenient for

plumbing and wiring.

Remember to keep the lengths of hot water pipe to a minimum in order to save energy.

•If the unit is to supply a basin, you can fit it either above or below the basin.

HOW TO INSTALL YOUR IL095

Deciding the wiringroute

•You have a choice of whether to feed the electric cable

through the side or through the back of the unit.

•If it going through the side of the unit, cut out the

plastic lug to expose the grommet (diagram 2).

•If is going through the back of the unit, cut through the

grommet on the backplate with a sharp knife (Take Care!).

Make sure you do not remove the grommet from the backplate (diagram 3).

Feed the cable through the grommet before you fix the unit to the wall.

Fixing to the wall

•Undo the retaining nuts and take the front cover

off the unit. Hold the backplate in position against

the wall whilst you mark the four fixing holes.

•Drill the holes and fix the unit to the wall using the

four No.8 x 38mm wood screws supplied.

Plumbing the unit

WARNING: IF A NON RETURN VALVE IS FITTED IN THE INLET FEED TO THE UNIT,

THEN THE INSTALLATION SHOULD ALSO INCLUDE A 3.5 BAR PRESSURE

REDUCING VALVE AND A 6 BAR PRESSURE RELIEF (EXPANSION) VALVE

WARNING: ENSURE THAT THE MAINS WATER SUPPLY MEETS THE REQUIREMENTS

LISTED ON PAGE 3 BEFORE CONTINUING WITH INSTALLATION.

WARNING: BEFORE CONNECTING THE PIPE WORK TO THE IL095,

ENSURE THAT THE PIPE WORK IS FULLY FLUSHED OUT.

Fitting the pipes

•The unit should be connected directly to the main cold water supply.

•We recommend that you use Ø15mm copperor stainless steel pipe for the inlet and outlet

connections.

•Use PTFE tape formaking screw joints. Do not use a jointing compound.

•Remember to keep the hot water pipe runs as short as possible.

In some cases, it may be worth fitting a second unit.

•If the unit is to supply more than one basin outlet, the head should be the same at each outlet if

they are to be used at the same time.

If not, one outlet will take all the water.

•When the pipework has been plumbed in, flush it through with water before you connect the

unit, to remove any swarf or loose particles.

Connecting the unit to the pipes

•The inlet and outlet are clearly marked on the unit.

They each have a Ø15mm straight shank connections.

•The unit comes with a service valve (diagram 5) which should be fitted on the inlet of the unit.

The valve can be used to turn off the water supply to the unit if it needs servicing, or to reduce

the main supply flow if it is too high.

Fitting the attachments

•If the unit is to supply a shower, you will also need a “Dimplex Mixer Unit”.

Available in chrome/white finish and suitable for surface or concealed pipe entry (see page 9).

•If the unit is to supply a shower, and the shower handset can reachwater in a bath or basin, you

must fit a vacuum breaker to comply with Water By-laws.

Vacuum breakers are available from our salesoffice (see page 9).

Alternatively, use the hose-retaining feature built into the soapdish.

Because water can sometimes seep through, you should position the vacuum breaker where

dripping will not do any damage.

•If the unit is to supply a basin, we recommend that you use spray taps, which you can get from

your local stockist (not Dimplex supplied).

MAKING THE ELECTRICAL CONNECTIONS

WARNING: THIS WATER HEATER MUST BE EARTHED.

The electrical installation must be in accordance with the current BS.7671 (IEE Wiring Regulations)

and “Part P” of the Building Regulations and/or local regulations

Wiring to the mains (Check the unit rating to see which applies)

•A 40 amp 240V supply is required for the 9.5kW unit

•A 45 amp 240V supply is required for the 10.8kW unit

•A 50 amp 240V supply is required for the 12.0kW unit

9.5kW IL095 Wiring Conditions:

If the cable run is less than 10 metres and is surface run, 6mm² cable can be used.

A means for disconnection in all poles must be incorporated in the fixed wiring in accordance with

the wiring rules.

The isolating switch should be rated at: 40 amps or greater for the 9.5kW unit.

Wire the unit using a suitable Fuse/MCB: 40 amps Fuse/MCB for the 9.5kW unit.

12.0kW and 10.8kW IL095 Wiring Conditions:

This unit has been designed to accept 10mm² supply cable. Therefore, this is the size of cable that

should be used between the isolator switch and the unit, even if you decide to use 16mm² between

the fuse box and isolating switch. 10mm² supply cable is recommended for the 12.0kW, and for long

cable runs (greater than 10 metres) also for the 10.8kW unit.

The isolating switch should be rated at: 45 amps for the 10.8kW unit / 50 amps forthe 12.0kW unit.

Wire the unit using 10mm² cable and a suitable Fuse/MCB:

45 amps Fuse/MCB for the 10.8kW unit / 50 amps Fuse/MCB for the 12.0kW unit.

If the unit is fitted in a bathroom:

9.5kW and 10.8kW IL095: A standard 45 amp cord operated isolatorswitch is recommended.

12.0kW IL095: A pull cord isolator switch is not available for this model. A double pole 50 amp

isolator switchis required. This must be mounted out of reach ofthe shower cubicle or bath.

Connecting the unit to the mains

•Strip back the insulation on the LIVE (brown or red) and NEUTRAL (Blue or black) mains wires

about 8mm. Strip backany insulation on the EARTH (green/yellow or green) about 20mm.

•Feed the cable through the side or rear entry grommets, as appropriate.

The outer sheath of the cable must project through the grommet (diagram 6).

If the side entry is used, this will stop water getting into the unit.

•Connect the cables to the terminal block and earth stud (diagram 6).

•Make sure that the live and neutral terminal block screws are tightened securely (1Nm minimum)

•Make sure that the earth wire is wrapped around its terminal stud and into the saddle washer.

The nut should be tightened securely (2 Nm minimum).

WARNING: FAILURE TO COMPLY WITH THESE INSTRUCTIONS COULD RESULT IN

FAILURE OF THE TERMINAL BLOCK

•Check that the Power Selector Screw) on theflow switch is set to “HI” (diagram 7).

If it is set to “LO” only one heater element will operate.

•Fit the front cover and tighten the retaining nuts.

Ensuring the earth continuity

•If the unit is fitted in a bathroom, to conformwith the current BS.7671 (formally IEE regulations),

the units earth continuity conductor must be effectively connected to ALL exposed metal parts of

ALL other appliances in the room.

CHECKING FOR LEAKS

•Let the water run through the unit for a few seconds. Check that no pipe joints leak.

ADJUSTING THE SERVICE VALVE

Turn the service valve on, then:-

•If the unit is to supply a basin,

- turn on the hot watertap fully at the basin.

- adjust the service valve until the water comes out of the tap at the required temperature.

- check that the unit works correctly when the basin tap is closed and then opened again:

if not, adjust the service valve slightly.

•If the unit is to supply a shower,

- turn the hot water tap on the mixer unit fully on.

- turn the service valve anti-clockwise until the neon light goes out, then turn it back until the

neon just comes on.

-check the water temperature at the handset and, if necessary, turn the cold tap on and adjust

to get the desired shower temperature.

WARNING: IN ORDER TO MAINTAINTHE PERFORMANCE OF YOUR SHOWER,

YOU MUST CLEANTHE SHOWER HANDSET REGULARLY.

All water contains particles of lime-scale, which build up in the shower handset and unit reducing the

performance.

It is therefore important to clean the shower handset by regularly dipping it in a suitable descaling

solution. The frequency of this will depend on water hardness and experience.

Explain to the user that when the unit is used, the hot water tap should be turned fully

on so that the unit will operate correctly.

COMMISSIONING YOUR IL095

WARNING: DO NOT USE THE UNIT IF YOU THINK IT MAY BE FROZEN, AS THIS COULD

RESULT IN SERIOUS DAMAGE TO THE UNIT. WAIT UNTIL YOU ARE SURE

THAT IT HAS COMPLETELY THAWED OUT BEFORE YOU SWITCH ON.

Basin

•Check that the power is switched on at the mains isolator switch.

•Turn on the hot water tap FULLY. If you do not turn the tap on, you will find that the

temperature of the water will vary. The hot water temperature willhave been set using the

service valve (diagram 5).

•If the unit has been used recently, run the water through for a few seconds to let the

temperature settle down, we advise you DO NOT enter the water flow during this time.

WARNING: YOU MAY INITIALLY GET A SHORT BURST OF VERY HOT WATER

FROM THE UNIT.

•If a second tap connected to the unit is also turned on, the hot water will be shared between the

two and so the flow will drop.

•When you have finished do not switch off thepower if you are going to use the unit again

shortly.

Shower

•Check that the power is switched on at the mains local isolator switch.

•Turn on the hot (or “flow”) tap FULLY (diagram 9).

•If the unit has been used recently, run the water through for a few seconds to let the

temperature settle down, we advise you DO NOT enter the water flow during this time.

WARNING: YOU MAY INITIALLY GET A SHORT BURST OF VERY HOT WATER

FROM THE UNIT.

•Turn on the cold (or “temperature”) tap, if necessary, to adjust the temperature of the water.

•Make sure that no other outlets connected to the unit are used whilst you are in the shower, or

the water flow will drop suddenly.

•When you have finished, do not switch off the power if you are going to use the unit again

shortly.

•It is important to cleanthe shower spray plate regularly (see page 7).

•In order for the IL095 to function correctly, the “Dimplex Mixer Kit” must be used.

The kit comes complete with full accessories including a 3 position multi-function shower

handset.

HOW TO USE YOUR IL095

DIMPLEX AFTER SALES SERVICE

SELF HELP

If the unit is not working satisfactorily, make the following checks before calling out the installer.

Any one of these adjustments could restore the performance.

Symptom Cause What to do

Little or no water flow The main water supply is turned

off Turn on the main supply fully at the

stop valve

Cold water only

- neon light off The main water supply is not

turned on enough Turn on the main supply fully at the

stop valve

Water too cold

- neon light on The water flow rate is too high

The inlet water temperature has

dropped

Adjust the service valve (see page 7)

For a shower, adjust the spray pattern

available on the multi-mode handset

Water flow too low, or

temperature too high The main water supply is too low

The hot tap is not fully open

Increase the supply water flow.

Make sure that the service valve is

correctly adjusted.

Adjust the service valve so that the

water is at the right temperature with

the tap fully open (see page 7)

Always turn the hot tap fully on.

Water goes from hot

to cold The water flow or pressure is too

low, and the thermal cut-out is

operating

A second outlet has been turned

Increase the supply water flow

Make sure that the service valve is

correctly adjusted

Do not use the basin whilst using the

shower

Shower spray pattern

deteriorates The shower handset is clogged Clean the handset using a descaling

solution if required (see page 9)

We offer a technical advisory service on the telephone to installers and other customers with

problems in the field.

RING 0845 600 5111

Remember to quote the exact type of unit, aswritten on the front ofthe shower and on this leaflet.

The model and serial number are located on the bottomface of the shower.

Make a note of those numbers here, and be sure to quote them if you call for advice.

Model Number: _ _ _ _ _ _ _ _ _ _ _ _ _ Serial Number: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

Note: You may be charged for aservice call if you do not have the serial number.

Please Note:- The fitting of Spare Parts must be supervised by a suitably qualified person.

Chrome and White Shower Mixer Unit Complete with full accessories

Including 3 position multi-function handset

For further details, including a comprehensive list off accessories and spare parts,

contact Dimplex Customer Services 0845 6000 5111

WHAT TO DO IF THINGS GO WRONG (1)

ADDITIONAL ACCESSORIES AND COMMON SPARE PARTS

WHAT TO DO IF THINGS GO WRONG (2)

PROFESSIONAL SERVICE

If the previous “Self Help” checks fail to restore the performance, you should seek professional help.

The person who installed the shower is probably the best one to investigate and correct it and is

certainly the person to contact if you have had a problem in the guarantee period.

The following additional checklist is provided for the benefit of the qualified service person.

WARNING:

SWITCH OFF THE ELECTRICITY AT THE LOCAL ISOLATOR

BEFORE REMOVING THE COVER TO MAKE CHECKS

Symptom Cause What to do

Little or no water flows

- neon light off The water pressure is very low Use a pump to boost the supply from

a storage tank

Cold water only

- neon light off The main water is connected to

the OUTLET of the unit

The water pressure is too low

The thermal cut-out has

triggered

The flow switch is not working

Reconnect the main supply to the

INLET (marked in blue)

Use a pump to boost the supply from

a storage tank.

Reset it by opening the unit and

pushing the button on the cut-out

(diagram 11). Before you do this you

must remove the cause of the

problem

Contact Dimplex

Water too cold

- neon light on The power select screw is set to

“LO”

One element is not working

The Power Supply Voltage has

dropped.

Change the power select screw to

"HI” (diagram 7).

Switch off the electricity supply and

check the resistance of the elements.

You should get the following readings.

Loading (kW) Resistance (Ohms)

9.5

12.0

10.8 10.6

12.0 9.6

The heater should only draw the

following currents:

40 amps for the 9.5kW model

45 amps for the 10.8kW model

50 amps for the 12.0kW model

Water flow too low or

temperature too high The service valve is fitted to the

OUTLET

There are constrictionsin the

plumbing

Fit the service valve to the INLET of

the unit

Check the plumbing. Only use PTFE

tape formaking pipe joints

Water goes from hot to

cold The service valve is fitted to the

OUTLET Fit the service valve to the INLET of

the unit

Inhaltsverzeichnis

Andere Dimplex Boiler Handbücher

Dimplex

Dimplex ECSd125-580 Leitfaden

Dimplex

Dimplex SUTP Mid Range Bedienungsanleitung

Dimplex

Dimplex AWP 30 HLW Bedienungsanleitung

Dimplex

Dimplex WWSP 335 Beilage

Dimplex

Dimplex LBW 300 Bedienungsanleitung

Dimplex

Dimplex IHW 35 Bedienungsanleitung

Dimplex

Dimplex AWP 300 LW Bedienungsanleitung

Dimplex

Dimplex Unvented Water Heater Bedienungsanleitung

Dimplex

Dimplex DEE 1802 Bedienungsanleitung

Dimplex

Dimplex FWS 27 Bedienungsanleitung

Dimplex

Dimplex 200 AIR D/2 Bedienungsanleitung

Dimplex

Dimplex FWS 27 Bedienungsanleitung

Dimplex

Dimplex Handyman Bedienungsanleitung

Dimplex

Dimplex SCx175sd Bedienungsanleitung

Dimplex

Dimplex PSW 1000 Bedienungsanleitung

Dimplex

Dimplex Edel 200 WATER/3 Bedienungsanleitung

Dimplex

Dimplex Edel EDL200UK-630 Leitfaden

Dimplex

Dimplex DEE 1802 Bedienungsanleitung

Dimplex

Dimplex Handyman Bedienungsanleitung

Dimplex

Dimplex DEE 1521 Bedienungsanleitung

Dimplex

Dimplex 500001099 Leitfaden

Dimplex

Dimplex DEE 1803 Bedienungsanleitung

Dimplex

Dimplex HWK 332 Econ Bedienungsanleitung

Dimplex

Dimplex PSP 1000K Benutzerhandbuch

Beliebte Boiler Handbücher anderer Marken

Kenmore

Kenmore 153.582400 Bedienungsanleitung

Applimo

Applimo Edel AIR Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Bedienungsanleitung

clage

clage E-Mini Series Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-180 Bedienungsanleitung

Bradford White

Bradford White EF Series Bedienungsanleitung

Eccotemp

Eccotemp 40-H Bedienungsanleitung

Dux

Dux 32FCR6N Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Fehlerbehebungshandbuch

Noritz

Noritz N-132M Gebrauchsanweisung

TESY

TESY GCV7/4S 10047 Technisches Datenblatt

A.O. Smith

A.O. Smith Gphe 50 Bedienungsanleitung

Koryo

Koryo KWHZF15Y Bedienungsanleitung

Pentair

Pentair PSC-14-4-02 Bedienungsanleitung

GE 40M06AAG Montageanleitung

Thermor

Thermor AEROMAX SPLIT 2 Bedienungsanleitung

American Hometec

American Hometec AHQ-B03X Bedienungsanleitung

PVI

PVI MAXIM Bedienungsanleitung