Directed Electronics Valet 561T Bedienungsanleitung

MMooddeell556611TT

IInnssttaallllaattiioonnGGuuiiddee

ttaabblleeooffccoonntteennttss

Code Hopping™, Doubleguard®, ESP™, FailSafe®, Ghost Switch™, Learn Routine™, Nite-Lite®,

Nuisance Prevention® Circuitry, Revenger®, Silent Mode™, Soft Chirp®, Stinger®, Valet®, Vehicle

Recovery System®, VRS®, and Warn Away® are all Trademarks or Registered Trademarks of

Directed Electronics.

wwhhaattiissiinncclluuddeedd................................................33

wwaarrnniinngg!!ssaaffeettyyffiirrsstt.............

.............................44

iinnssttaallllaattiioonnppooiinnttssttoorreemmeemmbbeerr..........................55

ffiinnddiinnggtth

heewwiirreessyyoouunneeeedd..................................66

finding the starter wire . . . . . . . . . . . . . . . . 6

obtaining constant 12V . . . . . . . . . . . . . . . . 6

finding the accessory wire. . . . . . . . . . . . . . . 7

finding the 12V switched ignition wire . . . . . . 7

finding the tachometer wire . . . . . . . . . . . . . 8

finding a (+) parking light wire . . . . . . . . . . . 8

finding the wait-to-start bulb wire for diesels . 9

pprriimmaarryyhhaarrnneessss((HH11))wwiirriinnggddiiaaggrraamm...........

.......1100

44--ppiinnssaatteelllliitteehhaarrnneessssddiiaaggrraamm..........................1100

hheeaavvyyggaauuggeerreellaayywwiirriinnggddiiaaggr

raamm......................1111

ddoooorrlloocckkhhaarrnneessss,,33--ppiinnccoonnnneeccttoorr....................1111

rreemmootteessttaarrtthhaar

rnneessss((HH22))wwiirriinnggddiiaaggrraamm............1111

pprriimmaarryyhhaarrnneessss((HH11)),,99--ppiinnccoonnnneeccttoorr................1122

hheeaavvy

yggaauuggeerreellaayyiinntteerrffaaccee..............................1166

rreemmootteessttaarrtthhaarrnneessss((HH22)),,55--ppiinnccoonnnneeccttoorr...

.......1177

nneeuuttrraallssaaffeettyysswwiittcchhiinntteerrffaaccee..........................1188

pre-1996 dodge dakota pickups with . . . . . . .

2.5 liter motors . . . . . . . . . . . . . . . . . . . . . 20

general motors trucks, SUVs, and column . . . .

shifting passenger cars . . . . . . . . . . . . . . . . 20

bbyyppaassssiinnggGGMMvveehhiicclleeaannttii--tth

heeffttssyysstteemmss((VVAATTSS))....2211

11999955aannddnneewweerrvveehhiicclleeaannttii--tthheeffttssyysstteemmss..........

((iimmmmoobbiilliizzeerrss))..................................................2222

passlock I and passlock II (PL-1 and PL-2) . . 22

passkey III (PK-3), transponder-based systems22

ooppttiioonnaallaannttii--ggrriinnddrreellaayy............................

......2233

iinntteerrnnaallpprrooggrraammmmiinnggjjuummppeerr............................2244

light flash (+)/(-) . . . . . . . . . . . . . . . . . . . 24

tach threshold on/off . . . . . . . . . . . . . . . . . 24

pplluugg--iinnpprrooggrraammsswwiittcchh....................................2255

ttaacchhlleeaarrnniinngg..................................................2255

to learn the tach signal . . . . . . . . . . . . . . . 25

ooppe

erraattiinnggsseettttiinnggsslleeaarrnnrroouuttiinnee........................2266

ffeeaattuurreessmmeennuu...............................

...................2277

ffeeaattuurreeddeessccrriippttiioonnss..........................................2288

rreeaarrddeeffooggggeer

rccoonnttrrooll........................................3311

ttiimmeerrmmooddee.......................................

...............3311

ssaaffeettyycchheecckk....................................................3322

ttrroouubblleesshhoooottiinng

g................................................3333

wwiirriinnggqquuiicckkrreeffeerreenncceegguuiiddee.....................

.........3355

wwhhaattiissiinncclluuddeedd

■TThheeccoonnttrroollmmoodduullee((sseeeeddiiaaggrraamm))

■TThheepplluugg--iinnpprrooggrraammsswwiittcchh

■AAhhooooddppiinnsswwiittcchh

■AAttoogggglleeoovveerrrriiddees

swwiittcchh

6-pin relay output

4-pin satellite/

harness

9-pin main harness

5-pin remote start

harness

not used

2-pin BLUE

program plug

status LED

not used

wwaarrnniinngg!!ssaaffeettyyffiirrsstt

The following safety warnings must be observed at all times:

■Due to the complexity of this system, installation of this product must only be performed by an authorized

Directed Electronics dealer.

■When properly installed, this system can start the vehicle via a command signal from the remote control

transmitter. Therefore, never operate the system in an area that does not have adequate ventilation. The fol-

lowing precautions are the sole responsibility of the user; however, authorized Directed Electronics dealers

should make the following recommendations to all users of this system:

1. Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage).

2. When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote

start system must be disabled using the installed toggle switch.

3. It is the user's sole responsibility to properly handle and keep out of reach from children all remote

control transmitters to assure that the system does not unintentionally remote start the vehicle.

4. TTHHEEUUSSEERRMMUUSSTTIINNSSTTAALLLLAACCAARRBBOONNMMOONNOOXXIIDDEEDDEETTEECCTTOORRIINNOORRAABBOOUUTTTTHHEELLIIVVIINNGGAARREEAAAADDJJAACCEENNTTTTOO

THHEEVVEEHHIICCLLEE..AALLLLDDOOOORRSSLLEEAADDIINNGGFFRROOMMAADDJJAACCEENNTTLLIIVVIINNGGAARREEAASSTTOOTTHHEEEENNCCLLOOSSEEDDOORRPPAARRTTIIAALLLLYY

EENNCCLLOOSSEEDDVVEEHHIIC

CLLEESSTTOORRAAGGEEAARREEAAMMUUSSTTAATTAALLLLTTIIMMEESSRREEMMAAIINNCCLLOOSSEEDD..

■Use of this product in a manner contrary to its intended mode of operation may result in property damage,

personal injury, or death. Except when performing the Safety Check outlined in this installation guide, (1)

Never remotely start the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the

keys in the ignition. The user will be responsible for having the neutral safety feature of the vehicle period-

ically checked, wherein the vehicle must not remotely start while the car is in gear. This testing should be

performed by an authorized Directed Electronics dealer in accordance with the Safety Check outlined in this

product installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult

with the user to fix the problem immediately.

■After the remote start module has been installed, test the remote start module in accordance with the Safety

Check outlined in this installation guide. If the vehicle starts when performing the Neutral Safety Shutdown

Circuit test, the remote start unit has not been properly installed. The remote start module must be removed

or properly reinstalled so that the vehicle does not start in gear. All installations must be performed by an

authorized Directed Electronics dealer. OOPPEERRAATTIIOONNOOFFTTHHEERREEMMOOTTEESSTTAARRTTMMOODDUULLEEIIFFTTHHEEV

VEEHHIICCLLEESSTTAARRTTSSIINN

GGEEAARRIISSCCOONNTTRRAARRYYTTOOIITTSSIINNTTEENNDDEEDDMMOODDEEOOFFOOPPEERRAATTIIOONN..OOPPEERRAATTIINNGGTTHHEERREEMMOOTTEESSTTAARRTTSSYYSST

TEEMMUUNNDDEERR

TTHHEESSEECCOONNDDIITTIIOONNSSMMAAYYRREESSUULLTTIINNPPRROOPPEERRTTYYDDAAMMAAGGEEOORRPPEERRSSOONNAALLIINNJJUURRYY..IIMMMMEEDDIIAATTEELLYYCCEEAASSEETTHHEEUUS

SEE

OOFFTTHHEEUUNNIITTAANNDDRREEPPAAIIRROORRDDIISSCCOONNNNEECCTTTTHHEEIINNSSTTAALLLLEEDDRREEMMOOTTEESSTTAARRTTMMOODDUULLEE..DDIIRREECCTTEEDDEELLEECCTTRROONNIICCSS

WWIILLLL

NNOOTTBBEEHHEELLDDRREESSPPOONNSSIIBBLLEEOORRPPAAYYFFOORRIINNSSTTAALLLLAATTIIOONNOORRRREEIINNSSTTAALLLLAATTIIOONNCCOOSSTTSS..

iinnssttaallllaattiioonnppooiinnttssttoorreemmeemmbbeerr

IIMMPPOORRTTAANNTT!!This product is designed for fuel-injected, automatic transmission vehicles only.

Installing it in a standard transmission vehicle is dangerous and is contrary to its intended use.

BBeeffoorreebbeeggiinnnniinnggtthheeiinnssttaallllaattiioonn::

■Please read this entire installation guide before beginning the installation. The installation of this remote

start system requires interfacing with many of the vehicle’s systems. Many new vehicles use low-voltage or

multiplexed systems that can be damaged by low resistance testing devices, such as test lights and logic

probes (computer safe test lights). Test all circuits with a high quality digital multi-meter before making con-

nections.

■Do not disconnect the battery if the vehicle has an anti-theft-coded radio. If equipped with an air bag, avoid

disconnecting the battery if possible. Many airbag systems will display a diagnostic code through their

warning lights after they lose power. Disconnecting the battery requires this code to be erased, which can

require a trip to the dealer.

■Remove the dome light fuse. This prevents accidentally draining the battery.

■Roll down a window to avoid being locked out of the vehicle.

AAfftteerrtthheeiinnssttaallllaattiioonn::

■Test all functions. The "Using Your System" section of the Owner's Guide is very helpful when testing.

■Complete the vehicle

Safety Check

outlined in this manual prior to the vehicle reassembly.

ffiinnddiinnggtthheewwiirreessyyoouunneeeedd

IIMMPPOORRTTAANNTT!!Do not use a 12V test light or logic probe (computer safe test light) to locate these

wires! All testing described in this manual assumes the use of a digital multimeter.

We recommend two possible sources for 12V constant: The (+) terminal of the battery, or the constant 12V supply

to the ignition switch. Always install a fuse within 12 inches of this connection. If the fuse will also be power-

ing other circuits, such as door locks, a power window module, or a Nite-Lite® headlight control system, fuse

accordingly.

IIMMPPOORRTTAANNTT!!Do not remove the fuse holder on the red wire. It ensures that the control module

has its own fuse, of the proper value, regardless of how many accessories are added to the main

power feed.

The starter wire provides 12V directly to the starter or to a relay controlling starter. In some vehicles, it is

necessary to power a cold start circuit. A cold start circuit will test exactly like a starter circuit, but it does not

control the starter. Instead, the cold start circuit is used to prime the fuel injection system for starting when the

vehicle is cold.

HHoowwttooffiinnddtthheessttaarrtteerrwwiirreewwiitthhyyoouurrmmuullttiimmeetteerr::

1. Set to DCV or DC voltage (12V or 20V is fine).

2. Attach the (-) probe of the meter to chassis ground.

3. Probe the wire you suspect of being the starter wire. The steering

column is an excellent place to find this wire. Remember you do not

need to interrupt the starter at the same point you test it. Hiding

your starter kill relay and connections is always recommended.

4. Turn the ignition key switch to the start position. Make sure the car

ffiinnddiinnggtthheessttaarrtteerrwwiirree

oobbttaaiinniinnggccoonnssttaanntt1122VV

is not in gear! If your meter reads (+)12V, go to the next step. If it doesn’t, probe another wire.

5. Cut the wire you suspect of being the starter wire.

6. Attempt to start the car. If the starter engages, reconnect it and go back to Step 3. If the starter does not

turn over, you have the right wire.

The ignition wire is powered when the key is in the run or start position. This is because the ignition wire powers

the ignition system (spark plugs, coil) as well as the fuel delivery system (fuel pump, fuel injection computer).

Accessory wires lose power when the key is in the start position to make more current available to the starter motor.

HHoowwttooffiinndd((++))1122VViiggnniittiioonnwwiitthhyyoouurrmmuullttiimmeetteerr::

1. Set to DCV or DC voltage (12V or 20V is fine).

2. Attach the (-) probe of the meter to chassis ground.

3. Probe the wire you suspect of being the ignition wire. The steering

column harness or ignition switch harness is an excellent place to find

this wire.

4. Turn the ignition key switch to the run position. If your meter reads

(+)12V, go to the next step. If it does not read (+)12V, probe another wire.

5. Now turn the key to the start position. The meter display should stay

steady, not dropping by more than a few tenths of a volt. If it drops close

to or all the way to zero, go back to Step 3. If it stays steady at (+)12V, you have found an ignition wire.

An accessory wire will show (+)12V when the key is in the accessory and run positions. It will not show (+)12V

during the cranking cycle. There will often be more than one accessory wire in the ignition harness. The correct

accessory wire will power the vehicle's climate control system. Some vehicles may have separate wires for the

blower motor and the air conditioning compressor. In such cases, it will be necessary to add a relay to power the

second accessory wire.

ffiinnddiinnggtthheeaacccceessssoorryywwiirree

ffiinnddiinnggtthhee1122VVsswwiittcchheeddiiggnniittiioonnwwiirree

Most vehicles use a (+) parking light circuit. The (+) parking light wire is often found near the light switch. In

many vehicles the light switch is built into the turn signal lever; in these vehicles the parking light wire can be

found in the steering column. The same wire can often be accessed in the kick panel or running board.

NNOOTTEE::Many Toyotas and other Asian vehicles, send a (-) signal from the switch to a relay. The

relay then sends (+)12V to the bulbs. Whenever you have difficulty finding a (+) parking light

wire near the switch, simply test the wires at any switch or control panel that is lit by the instru-

ment panel lighting. Remember, you need a (+) parking light wire that does not vary with the

dimmer setting.

HHoowwttooffiinnddaa((++))ppaarrkkiinngglliigghhttffllaasshhwwiirreewwiitthhyyoouurrmmuullttiimmeetteerr::

1. Set to DCV or DC voltage (12V or 20V is fine).

2. Attach the (-) probe of the meter to chassis ground.

3. Probe the wire you suspect of being the parking light wire. Usually, the area near the headlight/parking light

switch is an excellent area to start, as is the kick panel.

4. Turn on the parking lights. If your meter shows (+)12V, turn off the parking lights and make sure it goes back

to zero.

5. If it does return to zero, turn the parking lights back on and, using the dash light dimmer control, turn the

brightness of the dash lights up and down. If the meter changes more than a volt when using the dimmer,

look for another wire. If it stays relatively close to (+)12V, you have found your parking light wire.

NNOOTTEE::Vehicles that use a (-) signal from the switch to the factory relay may be interfaced

directly. (See H1/5 WHITE wire of Primary Harness (H1) Wire Connection Guide section.)

To test for a tachometer wire, a multimeter capable of testing AC voltage must be used. The tachometer wire will

show between 1V and 6V AC. In multi-coil ignition systems, the system can learn individual coil wires. Individual

coil wires in a multi-coil ignition system will register lower amounts of AC voltage. Also, if necessary, the system

ffiinnddiinnggtthheettaacchhoommeetteerrwwiirree

ffiinnddiinnggaa((++))ppaarrkkiinngglliigghhttwwiirree

can use a fuel injector control wire for engine speed sensing. Common locations for a tachometer wire are the

ignition coil itself, the back of the gauges, engine computers, and automatic transmission computers.

IIMMPPOORRTTAANNTT!!Do not test tachometer wires using a test light or logic probe. The vehicle will be

damaged.

HHoowwttooffiinnddaattaacchhoommeetteerrwwiirreewwiitthhyyoouurrmmuullttiimmeetteerr::

1. Set to ACV or AC voltage (12V or 20V is fine).

2. Attach the (-) probe of the meter to chassis ground.

3. Start and run the vehicle.

4. Probe the wire you suspect of being the tachometer wire with the red probe of the meter.

5. If this is the correct wire the meter will read between 1V and 6V.

In diesel vehicles it is necessary to interface with the wire that turns on the WAIT-TO-START light in the dash-

board. This wire illuminates the bulb until the vehicle’s glow plugs are properly heated. When the light goes out

the vehicle can be started. This wire is always available at the connector leading to the bulb in the dashboard.

It can also be found at the Engine Control Module (ECM) in many vehicles.

TTootteessttaannddddeetteerrmmiinneetthheeppoollaarriittyyoofftthhiissw

wiirree::

1. Set your multimeter to DCV or DC voltage (12 or 20V is fine).

2. Attach the (+) probe of the meter to (+)12V.

3. Probe the wire that you suspect leads to the bulb with the (-) probe of the meter.

4. Turn the ignition switch to the ON position.

5. If the meter indicates 12 volts until the light goes out you have isolated the correct wire and the wire's polar-

ity is negative (ground while the bulb is on).

6. If the meter reads zero volts until the light goes out and then reads 12 volts, you have isolated the correct

wire and the wire's polarity is positive.

ffiinnddiinnggtthheewwaaiitt--ttoo--ssttaarrttbbuullbbwwiirreeffoorrddiieesseellss

pprriimmaarryyhhaarrnneessss((HH11))wwiirriinnggddiiaaggrraamm

______

44--ppiinnssaatteelllliitteehhaarrnneessssddiiaaggrraamm

______

______ PPIINNKKIIGGNNIITTIIOONNTTRRIIGGGGEERR

PPUURRPPLLEESSTTAARRTTEERRTTRRIIGGGGEERR

OORRAANNGGEEAACCCCEESSSSOORRYYTTRRIIGGGGEERR

BBLLUUEESSTTAATTUUSSOOUUTTPPUUTT

WWHHIITTEE((++//--))LLIIGGHHTTFFLLAASSHH

BBLLAACCKKGGRROOUUNNDD

RREEDD//WWHHIITTEENNOOTTUUSSEEDD

WWHHIITTEE//RREEDD((++))AACCTTIIVVAATTIIOONNIINNPPUUTT

GGRRAAYY//BBLLAACCKK((--))WWAAIITTTTOOSSTTAARRTTIINNPPUUTT

WWHHIITTEE//BBLLUUEE((--))AACCTTIIVVAATTIIOONNIINNPPUUTT

YYEELLLLOOWW((++))IIGGNNIITTIIOONNOOUUTT((TTOOAALLAARRMM))

GGRREEEENN//WWHHIITTEEFFAACCTTOORRYYRREEAARRMM

LLIIGGHHTTGGRREEEENN//BBLLAACCKKFFAACCTTOORRYYDDIISSAARRMM

HH11//11

HH11//22

HH11//33

HH11//44

HH11//55

HH11//66

HH11//77

HH11//88

HH11//99

Andere Handbücher für Valet 561T

Inhaltsverzeichnis

Andere Directed Electronics Fernstartsystem Handbücher

Directed Electronics

Directed Electronics AS-1775 Bedienungsanleitung

Directed Electronics

Directed Electronics Smart start Bedienungsanleitung

Directed Electronics

Directed Electronics Python G4203P Bedienungsanleitung

Directed Electronics

Directed Electronics ProStart CT-5472TW Bedienungsanleitung

Directed Electronics

Directed Electronics AS-6870TW-FM Bedienungsanleitung

Directed Electronics

Directed Electronics Python 1401 Bedienungsanleitung

Directed Electronics

Directed Electronics 3200HS Bedienungsanleitung

Directed Electronics

Directed Electronics XK811 Bedienungsanleitung

Directed Electronics

Directed Electronics Viper 5501 Bedienungsanleitung

Directed Electronics

Directed Electronics CLIFFORD 1.3X Bedienungsanleitung

Directed Electronics

Directed Electronics Xpresskit CANMAX400 Bedienungsanleitung

Directed Electronics

Directed Electronics Valet 561T Bedienungsanleitung

Directed Electronics

Directed Electronics 3000 Bedienungsanleitung

Directed Electronics

Directed Electronics Failsafe 103T Bedienungsanleitung

Directed Electronics

Directed Electronics 435 Bedienungsanleitung

Directed Electronics

Directed Electronics Valet 561R Bedienungsanleitung

Directed Electronics

Directed Electronics AS-1271 Bedienungsanleitung

Directed Electronics

Directed Electronics READY REMOTE 24927 Kurzanleitung

Directed Electronics

Directed Electronics 991 Bedienungsanleitung

Directed Electronics

Directed Electronics 410 Bedienungsanleitung

Directed Electronics

Directed Electronics 4400 Bedienungsanleitung

Directed Electronics

Directed Electronics CLIFFORD 1.3X Bedienungsanleitung

Directed Electronics

Directed Electronics 560T Bedienungsanleitung

Directed Electronics

Directed Electronics ONE-WAY FM AUTOMATIC/MANUAL TRANSMISSION Bedienungsanleitung

Beliebte Fernstartsystem Handbücher anderer Marken

AstroStart

AstroStart 803U Bedienungsanleitung

Durite

Durite 0-649-20 Handbuch

EINHELL

EINHELL BT-PS 1000 Handbuch

Linear

Linear ACCESS AK-21 Technische Daten

Soundstream

Soundstream TARANTULA RS.2 Bedienungsanleitung

Jaycar Electronics

Jaycar Electronics MB3752 Bedienungsanleitung

Ultra Start

Ultra Start 72 Series Bedienungsanleitung

ADS

ADS FLASHLOGIC FLRSVW1 Bedienungsanleitung

Selecta

Selecta JS012 Bedienungsanleitung

Black Widow Security

Black Widow Security BW RAS 400 Bedienungsanleitung

Vector

Vector Power City DK080706 Beilage

Code Alarm

Code Alarm CA-535 Bedienungsanleitung

Ozito

Ozito OJS-800 Bedienungsanleitung

Profi-Partner

Profi-Partner 46387 Bedienungsanleitung

EZ STARTER

EZ STARTER EZ-45 Bedienungsanleitung

Viper

Viper 4204 Bedienungsanleitung

Essex Electronics

Essex Electronics KE-1701 Bedienungsanleitung

EINHELL

EINHELL EGS 3600 Handbuch