Directed Directechs DB3 Bedienungsanleitung

INSTALLATION GUIDE

DB3

2015 Subaru Forester - 403.SUBARU2 1.25

This product is intended for installation by a professional installer only! Attempts to install this

product by a person other than a trained professional may result in severe damage to a vehicle’s

electrical system and components.

Introduction 4

Pre-installation and application warnings 5

Wiring diagram 6

Key release connection 20

Vehicle connections 7

Key2GO 9

Connecting the module 10

Module programming 11

LED diagnostics and troubleshooting 12

Soft reset 14

Hard reset 15

Feature programming 16

Feature and option list 17

Limited one year consumer warranty 18

Quick reference guide 19

Contents

3403.SUBARU2 1.25 2015 Subaru Forester

Warning! Safety ﬁrst

The following safety warnings must be observed at all times:

• Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer.

• When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never

operate the system in an area that does not have adequate ventilation.

The following precautions are the sole responsibility of the user; however, authorized Directed dealers should:

• Never use a test light or logic probe when installing this unit. Always use a multimeter.

• Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage).

• When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote start system must

be disabled using the installed toggle switch. It is the user’s sole responsibility to properly handle and keep out of reach from

children all remote controls to assure that the system does not unintentionally remote start the vehicle.

• USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE.

ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE

STORAGE AREA MUST REMAIN CLOSED AT ALL TIMES.

Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or

death. Except when performing the Safety Check outlined in this installation guide, (1) Never remotely start the vehicle with

the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user is responsible for having the

neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear.

This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in this product

installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the user to ﬁx the problem

immediately.

OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF

OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE

OR PERSONAL INJURY. IMMEDIATELY CEASE THE USE OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTE

START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS.

Remote starters for manual transmission pose signiﬁcant risks if not properly installed and operated. When testing to ensure the

installation is working properly, only remote start the vehicle in neutral gear, on a ﬂat surface and with a functional, fully engaged

parking brake. Do not allow anyone to stand in front of or behind the vehicle.

This product should not be installed in any convertible vehicles, soft or hard top with a manual transmission. Installation in such

vehicles may pose certain risk.

4403.SUBARU2 1.25 2015 Subaru Forester

Introduction

DB3 is an all-in-one door lock and override module.

Warning!

This solution is compatible with the 2015 Subaru Forester and offers the following features:

• DL-Arm Factory Security

• DL-Disarm Factory Security

• DL-Door Lock Control

• DL-Door Unlock

• DL-Driver Priority Unlock

• DL-Trunk / Hatch Release

• FOB-Control of aftermarket alarm with OEM remote

• Key2GO

• PK-Immobilizer Bypass-Data No Key Req'd

• RS-3x LOCK START (Start control using OEM Remote)

• RS-3x LOCK STOP (Stop control using OEM Remote)

• RS-SmartStart

• RS-Tach / RPM Output

• SS-Entry Monitoring ALL Door Pins

• SS-Entry Monitoring Trunk/Hatch Pin

• ST-Brake Status (foot brake)

• ST-E-Brake Status

• ST-Ignition Status

This module can only be flashed and configured using DirectLink at www.directechs.com or using the Directechs

Mobile application for smartphones. Refer to “Connecting the module” for more information.

5403.SUBARU2 1.25 2015 Subaru Forester

Pre-installation and application warnings

Firmware notes: This section highlights important information for this speciﬁc ﬁrmware and will assist in

pricing accordingly, as well as bringing awareness to any operational or vehicle limitations.

T-Harness

compatible

Keys required for

programming 1Keys required for

operation 0

Key2GO is mandatory to control the immobilizer override in this ﬁrmware.

Unless speciﬁed otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic

connector.

For clutch information, refer to Directwire vehicle information and to tech tip #10000.

Refer to "Vehicle connections" following the wiring diagram.

General notes: This section highlights important information for this speciﬁc ﬁrmware.

[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.

[2] Keysense input connection ONLY needed if Keysense is not recognized through data at the time of programming. Refer to

"LED Diagnostics & Troubleshooting" for more information.

Additional parts required (maximum required):

Diode 6A

0 x 1A Diodes 86 85

87a

1 x Relay

Resistor 100Ω

0 x Resistor

Fuse 7.5A

0 x Fuse

6403.SUBARU2 1.25 2015 Subaru Forester

(+) Brake Status Input

[1] (AC) Tach Input

(-) Trunk Status Input

(-) Door Status Input

(-) E-Brake Status Input

Remote

Starter

(-) GWR (Status)

(-) Lock Output

(-) Unlock Output

(-) Trunk Output

(-) Parking Light

(-) Ground(-) Ground

1: Green: (-) Lock Input

2: Blue: (-) Unlock Input

7: Pink/White: (+) Keysense Input [2]

3: Red/White: (-) Trunk Input

10: Blue/White: (-) GWR (Status) Input

[1] (AC) Tach Output: Violet/White: 5

Immo. Data (veh. side): Orange/Black: 11

(-) Door Status Output: Green/White: 3

(-) Trunk Status Output: Red/Black: 4

(-) E-Brake Status Output: Black/White: 1

(-) Security Light Output: Green/Black: 2

(+) 12V

(+) 12V: Red: 13

(-) Ground (-) Ground: Black: 14

Keyless Data (veh. side): Yellow: 8

Keyless Data (conn. side): Orange/Yellow: 9

HS CAN High: Tan/Black: 3

HS CAN Low: Tan: 4

Keyless Data:

pin 11

(-) Security Light: pin 26

(-) Parking Light: pin 17

(+) Brake Status: Gray: 6

Keyless Data (conn. side): Yellow/Black: 10

i171, 31-pin white conn. (D)

(behind fusebox)

B281, 35-pin white conn. (B)

(behind fusebox)

86 85

87a

(+) 12V

(+) Starter 2

(+) Accessory

(+) Ignition 1

(+) Ignition 2

(+) Starter 1

(+) Starter 2: pin 7

(+) Starter 1:

pin 3

(+) Ignition 1: pin 1

(+) Ignition 2: pin 6

(+) Accessory:

pin 2

(+) 12V: pin 4

B72, 8-pin

Ignition conn.

(at ignition switch)

(+) 12V

4 3

Not required in D2D mode.

Immo Data (veh. side): Orange/Red: 10

Immo Data (conn. side): Yellow/Red: 11

BCM

(behind the fuse box)

HS CAN High:

pin 20

HS CAN Low:

pin 28

76543 2 1

1716 1415 1213 1011 89

27 26 2425 2223 2021 1819

34 33 32 3031 2829

Immo. Data: pin 31

7 6 5 4 3 2 1

1716 1415 1213 1011 89

25 24 2223 2021 1819

31 30 28 262729

765 4 3 2

1918 1617 1415 1213 1011

27 26 2425 2223

35 34 32 3031

(+) Keysense: pin 4

B280, 34-pin

White conn. (A)

(behind fusebox)

Wiring diagram

P#: XKD2D65

(-) Ground

(+)12V

7403.SUBARU2 1.25 2015 Subaru Forester

7 6 5 4 3 2 1

1718

16 12

13 9

B281, 35-pin white conn. (B)

(right of steering column)

Only required for Pit Stop Mode or Manual Transmission vehicles.

ABC D

BCM (behind the fuse box)

(+) Key Release 1: pin 4

(-) Key Release 2: pin 3

86 85

87a

(+) 12V

86 85

87a

(+) 12V

(-) Ground

(-) Key Release Output: Blue/Red: 12

Connector location

Key release connection

8403.SUBARU2 1.25 2015 Subaru Forester

Vehicle connections

The connection information listed below is specific to the 2015 Subaru Forester. Refer to “Pre-installation and application warnings” for a list of important notes.

Data 14-pin blue connector (H1)

Module Connects To

Conn./Pin Color Description Wire Location (+/-) Wire Color Ref.

H1/1 Light Green (DATA) No Connection

H1/2 Violet/Yellow (DATA) No Connection

H1/3 Tan/Black (DATA) HS CAN High BIU behind dash fuse box, white 35 pin plug (B), pin 20 data red

H1/4 Tan (DATA) HS CAN Low BIU behind dash fuse box, white 35 pin plug (B), pin 28 data blue

H1/5 Orange/Green (DATA) No Connection

H1/6 Orange/Brown (DATA) No Connection

H1/7 Brown Relay N.O. No Connection

H1/8 Yellow Relay COM Keyless Data BIU behind dash fuse box, white 31 pin plug (D), pin 11 data green (keyless data)

H1/9 Orange or Orange/Yellow Relay N.C. Keyless Data BIU behind dash fuse box, white 31 pin plug (D), pin 11 data green (keyless data)

H1/10 Orange/Red Relay N.C. Immo Data BIU behind dash fuse box, white 34 pin plug (A), pin 31 data red/yellow

H1/11 Yellow/Red Relay COM Immo Data BIU behind dash fuse box, white 34 pin plug (A), pin 31 data red/yellow

H1/12 Brown/Red Relay N.O. No Connection

H1/13 Red (+) W2W Only - 12 Volt ignition switch, white 8 pin plug, pin 4 + yellow (40A) (common)

H1/14 Black (-) W2W Only - Ground

Output 12-pin red connector (H2)

Module Connects To

Conn./Pin Color Description Wire Location (+/-) Wire Color Ref.

H2/1 Black/White (-) W2W Only - E-Brake Output

H2/2 Green/Black (-) Security Light BIU behind dash fuse box, white 31 pin plug (D), pin 26 - brown/red

H2/3 Green/White (-) W2W Only - Door Output

H2/4 Red/Black (-) W2W Only - Trunk Output

H2/5 Violet/White (AC) W2W Only - Tach Output

H2/6 Gray (+) W2W Only - Brake Output

H2/7 Gray/Black (+) No Connection

H2/8 Violet/Green (MUX) No Connection

H2/9 Violet/Brown (MUX) No Connection

H2/10 Yellow/Black (Data) Keyless Data BIU behind dash fuse box, white 31 pin plug (D), pin 11 data green (keyless data)

H2/11 Orange/Black (Data) Immo Data BIU behind dash fuse box, white 34 pin plug (A), pin 31 data red/yellow

H2/12 Blue/Red (-) W2W Only - Key Release Output Must use a relay.

9403.SUBARU2 1.25 2015 Subaru Forester

Input 10-pin black connector (H3)

Module Connects To

Conn./Pin Color Description Wire Location (+/-) Wire Color Ref.

H3/1 Green (-) W2W Only - Lock Input

H3/2 Blue (-) W2W Only - Unlock Input

H3/3 Red/White (-) W2W Only - Trunk Input

H3/4 White/Violet (-) No Connection

H3/5 Violet/Black (-) No Connection

H3/6 White/Black (-) No Connection

H3/7 Pink/White (+) Keysense Input BIU behind dash fuse box, white 34 pin plug (A), pin 4 + black/white

H3/8 Violet (+) No Connection

H3/9 Pink (+) No Connection

H3/10 Blue/White (-) W2W Only - Ground When Running (Status) Input

D2D 4-pin white connector (H4)

Module

Conn./Pin Color Description

H4/1 Green (Data) TX

H4/2 Black (-) Ground

H4/3 Blue (Data) RX

H4/4 Red (+) 12 Volt

RF 2-pin white connector (H5)

Module

Conn./Pin Color Description

H5/1 N/A

H5/2 N/A

10 403.SUBARU2 1.25 2015 Subaru Forester

Key2GO

This feature is mandatory to control the immobilizer override in this ﬁrmware.

Key2GO has been designed and developed to bypass the advanced encryption layers found in modern vehicles. It uses an array

of servers to generate a duplicate of the original key, allowing the installation of a remote starter without having to give up a key.

The advantage is that this feature allows you to use one original key and the server to conﬁgure the bypass in the vehicle.

All Key2GO-compatible ﬁrmware are clearly indicated in the function list of each vehicle search result page and will also appear

on the ﬂash page. Any ﬁrst-time user must re-register to gain access to Key2GO, and some additional information will be required

to complete the registration process, such as your Directed account number and store name.

Key2GO is compatible with XKLoader2 and the online web tool, as well as XKLoader3 and the Directechs Mobile application.

Refer to “Module programming” of this guide for instructions on how to program features using Key2GO.

Andere Handbücher für Directechs DB3

Inhaltsverzeichnis

Andere Directed Autozubehör Handbücher

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed 403.SUBARU11 Bedienungsanleitung

Directed

Directed 403.NISS4HT 2.39 RSR Bedienungsanleitung

Directed

Directed 5305 Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed DS3+ Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed DS4+ Bedienungsanleitung

Directed

Directed Xpresskit DBALL2 Bedienungsanleitung

Directed

Directed FORD6 Gebrauchs- und Pflegehandbuch

Directed

Directed Directechs DS3 Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed DS4+ Bedienungsanleitung

Directed

Directed DBALL Bedienungsanleitung

Directed

Directed Directechs DB3 Bedienungsanleitung

Directed

Directed DIRECTECHS CHRYSLER8 Bedienungsanleitung

Directed

Directed 403.SUBARU2 Bedienungsanleitung

Directed

Directed Xpresskit dball 2 Bedienungsanleitung

Directed

Directed VOXX DEI 933.VW14 v2.11.198.12 Bedienungsanleitung

Directed

Directed CHRYSLER9 Bedienungsanleitung

Directed

Directed 403.TL10 Bedienungsanleitung

Directed

Directed DS3+ Bedienungsanleitung

Directed

Directed DS4+ Bedienungsanleitung

Directed

Directed DBALL Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Renault

Renault 77 11 423 180 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung